synonymRaymond Mill(Raymond mill) generally refers to Raymond mill
This machine adopts the advanced structure of similar products at home and abroad, and is updated and improved on the basis of Raymond mill in the same industryBall millHigh efficiency, low power consumption, small floor area and small one-time investment.Grinding rollstaycentrifugal forceUnder the action ofGrinding ringTherefore, when the grinding roll and ring wear to a certain thickness, the output and fineness of finished products will not be affected.The replacement cycle of grinding roller and grinding ring is long, thus eliminatingCentrifugal millShorter replacement cycle of vulnerable parts.The air flow of this machine isFan—Grinding shell—cyclone separator - There is less dust than that of high-speed centrifugal mill due to circulating flow in the fan, and the operation workshop is clean and the environment is free of pollution.
Chinese name
raymond mill
Foreign name
Raymond mill
Structure
By host, analyzer, fan, etc
Features
The whole machine is of vertical structure, with small floor area
Raymond mill is widely applicable toBarite、calcite、Potash feldspar, talc, marble, limestone, dolomite, fluorspar, limeActivated clay, activated carbon, bentonite, kaolin, cement, phosphate rock, gypsum, glass, thermal insulation materials, etcMohs hardnessHigh fine milling and processing of more than 280 kinds of non flammable and explosive materials in mineral, chemical, construction and other industries with humidity below 6% and no more than 9.3,R Raymond millThe particle size of the finished product can be adjusted freely within the range of 80-325 meshes, and some materials can reach up to 600 meshes.
Main structure
Announce
edit
The machine structure is mainly composed of host, analyzer, fan and finished productcyclone separator , fine powder cyclone separator and air duct.The host is composed of frame, air inlet volute, blade, grinding roller, grinding ring and housing.
During operation, the materials to be crushed are fed into the machine from the feed hopper at the side of the housing. The grinding roller device suspended on the plum blossom rack of the main machine rotates around the vertical axis and rotates itself at the same time. Due to the centrifugal force during rotation, the grinding roller swings outward and presses against the grinding ring, enabling the blade to scoop up the materials and send them between the grinding roller and the grinding ring,The purpose of crushing materials is achieved due to the rolling compaction of the grinding roller.
Raymond mill air separation process
Announce
edit
After material grinding, the fan blows the air into the main machine shell to lift the powder, which is sorted by the analyzer placed above the grinding room. The fine and coarse materials fall into the grinding room for regrinding. The fine and coarse materials that meet the specifications enter the cyclone collector with the wind flow, and are collected and discharged through the powder outlet, which is the finished product.The air flow returns to the fan from the return air pipe at the upper end of the large cyclone collector. The air path is circular and flows under negative pressure. The increased air volume of the circulation air path is discharged through the exhaust pipe between the fan and the host, and enters the small cyclone collector for purification.
Model parameters
Announce
edit
The model parameters of Raymond mill are as follows:
model
6R4525
5R4119
4R3216
3R90
3R85
3R75
3R65
3R60
parameter
4R90
4R85
Feed particle size (mm)
≤30
≤25
≤25
≤25
≤20
≤20
≤15
≤15
Grain size of finished product (mm)
0.125-
zero point zero four four
0.125-
zero point zero four four
0.125-
zero point zero four four
0.125-
zero point zero four four
0.125-
zero point zero four four
0.125-
zero point zero four four
0.125-
zero point zero four four
0.125-
zero point zero four four
Shift production of different material fineness (t)
16-120
8-60
4-45
3-35
2-28
1.5-20
1-18
0.5-8
Central shaft speed (r/min)
eighty-two
one hundred and five
one hundred and thirty
one hundred and sixty
one hundred and sixty
one hundred and sixty
one hundred and eighty
two hundred and eighty
Grinding ring diameter (mm)
one thousand seven hundred and seventy
one thousand and four hundred
one thousand and seventy-three
nine hundred and seventy-three
eight hundred and eighty-five
eight hundred and sixty-five
seven hundred and twenty-five
four hundred and ninety-five
Grinding roll diameter (mm)
four hundred and fifty
four hundred and ten
three hundred and twenty
three hundred
two hundred and seventy
two hundred and sixty
two hundred and ten
one hundred and forty
Grinding roller height (mm)
two hundred and fifty
one hundred and ninety
one hundred and sixty
one hundred and sixty
one hundred and fifty
one hundred and fifty
one hundred and fifty
one hundred
Main engine motor
y315m-
4-132
y280s-
4-75
y225s-
4-37
y225m-
8-30
y225m-
8-22
y225s-
8-18.5
y200L-
8-15
y160m-
6-7.5
Fan motor
y315m-
4-132
y250m-
4-75
y200L-
4-37
y180m-
4-22
y160L-
4-15
y160L-
4-15
y160m-
4-11
y132s-
2-5.5
Analyzer motor
y160m-
4-11
yc200-
4B-7.5
yc120-
4a-5.5
y112m-
6-2.2
y112m-
6-2.2
y112m-
6-202
y112m-
6-2.2
y90L-
6-1.1
Use and maintenance
Announce
edit
1、raymond mill Before installation, operators must receive necessary technical training to make them understand the principle and performance of Raymond mill and be familiar with the operating procedures of Raymond mill.During the use of Raymond mill, there should be fixed personnel to take care of it, and the operators must have a certain level of technology.
2. In order to make Raymond mill normal, the "equipment maintenance safety operation system" shall be formulated to ensure long-term safe operation of the mill, and necessary maintenance tools, grease and corresponding accessories shall be provided.
3. After Raymond mill has been used for a period of time, it shall be overhauled, and wear parts such as grinding roll, grinding ring, blade, etc. shall be overhauled and replaced. The connecting bolts and nuts of the grinding roll device shall be carefully checked before and after use to see whether there is looseness and whether the lubricating grease is sufficient.
4. When the grinding roll device of Raymond mill has been used for more than 500 hoursRolling bearingIt must be cleaned, and the damaged parts shall be replaced in time. Manual refueling pump and grease gun can be used as refueling tools.
5. When the machine is stopped, stop feeding first, and the main machine continues to rotate, so that the residual materials can continue to be ground. After about one minute, the main machine motor can be turned off to stop the grinding work, and then the fan motor and analyzer motor can be stopped.
Performance characteristics
Announce
edit
1. The whole machine is a vertical structure, which occupies a small area and is highly systematic. It can form an independent production system from rough processing of raw materials to transportation to milling and final packaging.
2. Compared with other milling equipment, the screening rate is up to 99%.
3. The transmission device of the main engine adopts sealed gear box and pulley, which ensures stable transmission and reliable operation.
4. The important parts of Raymond Mill are made of high-quality castings and profiles, and the process is fine, ensuring the durability of the whole equipment.
5. The electrical system of Raymond Mill adopts centralized control, and the model selection is advanced, reasonable and highly automated.