multistagecentrifugal pumpIt is the combination of more than two centrifugal pumps with the same function, and the fluid channel structure is shown in the first stage mediumPressure relief portIt is connected with the inlet of the second stage, and the medium pressure relief port of the second stage is connected with the inlet of the third stage. Such a mechanism in series forms a multistage centrifugal pump.
The significance of multistage centrifugal pump is to increase the set pressure.
1. The multi-stage centrifugal pump is a vertical structure with a small floor area. The center of gravity of the pump coincides with the center of the pump foot, so it runs stably, has small vibration and long service life.
2. The multi-stage centrifugal pump has the same caliber and is on the same horizontal centerline. It can be directly installed at any part of the pipeline without changing the pipeline structure, which is very convenient for installation.
3. Motor externalRain coverIt can be directly placed outdoors for use without the need to build a pump room, greatly savingInfrastructure investment。
Structural drawing of multistage centrifugal pump
4. The lift of multistage centrifugal pump can meet different requirements by changing the pump stages (number of impellers), so it has a wide range of applications. 5、Shaft sealuseHard alloyMechanical seal, reliable sealing, no leakage,Mechanical lossSmall.
6. High efficiency, energy saving and beautiful appearance.
7. Note: Internal casting with diameter above 50 is formed.
Scope of application
Announce
edit
Multistage centrifugal pump, which adopts the high efficiency and energy saving recommended by the statehydraulic modelWith high efficiency and energy saving, wide performance rangeOperation safetyStable, low noise, long life, easy installation and maintenance, etc;By changing the material and sealing form of the pump and adding a cooling system, hot water, oil, corrosive and abrasive media can be transported.
Type D pump is used to transport clean water or physical materials that do not contain solid particles and whose temperature is not higher than 80 ℃chemical propertyLiquid similar to clean water, suitable for mines and citiesWater supply and drainage engineeringuse.
DG type pump is used to transport clean water without solid particles and with a temperature not higher than 105 ℃ or liquid with physical and chemical properties similar to clean waterBoiler feed waterOr medium for transporting hot water or similar hot water.
MD pump is used to transport neutral materials with solid particle content no more than 1.5%Mineral water(particle size is less than 0.5millimeter)And other similar sewage, the temperature of the conveyed medium is not higher than 80 ℃, suitable for steel plantsMine drainage, sewage transportation, etc.
The delivery temperature of DF pump is - 20 ℃~105 ℃, without solid particles and corrosive liquid.
1. Pre startup inspection of multistage centrifugal pump
Whether the name, model, main performance and filling quantity of lubricating oil meet the requirementsTechnical documentsRequirements;Bearinglubrication system, sealing system andCooling systemWhether it is in good condition, and whether the oil and water paths of the bearing are unblocked;
Turn the rotor of the pump for 1-2 revolutions, and check whether there is friction or seizure of the rotor;
The valve or accessory device of the pump working system shall be at the position with the minimum load when the pump is running, and the outlet shall be closedRegulating valve;
Start the multistage centrifugal pump and check whether the impeller rotation is consistent with the design rotation. If not, the impeller must be completely stopped and the motor wiring must be adjusted before starting again.
2. Multi stage centrifugal pump water filling
Before starting the pump, the pump casing and suction pipe must be filled with water, because the vacuum of multistage centrifugal pump suction cannot be formed and maintained in the presence of air.
3. Multi stage centrifugal pump warming
Pumps for delivering high-temperature liquids, such as those in power plantsBoiler feed pumpWarm up the pump before starting the multistage centrifugal pump.that is becauseFeed pumpDuring startup, high temperature feed water flows through the pump, making the temperature of the pump body rise quickly from normal temperature to 100~200 ℃, which will cause the temperature difference between the inside and outside of the pump and between various components. Without sufficient heat transfer time and appropriate measures to control the temperature rise, uneven expansion of the pump will occur everywhere, causing deformation, wear, vibration and bearing axle seizure accidents of various parts of the pump body.
maintain
Announce
edit
Cleaning items
1、 Scrape off the inner and outer surfaces of the impeller andSealing ringThe scale and rust accumulated in the bearing and other places shall be cleaned and blown with water or compressed air.
2、 Clean the deposits on the joint surfaces of the shellOil stainAnd rust.
3、 Clean the water seal pipe and check whether the pipe is unblocked.
5、 Parts and components not to be assembled temporarily shall be protected with oil after cleaning.
Basic cleaning principles
1. Ensure that the requirements for cleanliness of parts are met. During repair, different parts have different requirements for cleanliness.In assembly, the cleaning requirements of mating parts are higher than those of non mating parts, and that of moving mating parts are higher thanStatic fitPrecision parts are higher than non precision parts.For the surfaces of sprayed, plated and bonded workpieces, the cleaning requirements are very high.Different cleaning agents and cleaning methods must be adopted according to different requirements
Methods to ensure the required cleaning quality.
2. Prevent corrosion of parts, and do not allow any degree of corrosion of precision parts.When the parts need to be parked for a period of time after cleaning, the antirust ability of the cleaning solution or other antirust measures should be considered.
3. Ensure operation safety, and prevent fire or poisoning to human body and environmental pollution.