-
Tesla seat backrest steel wire injection refers to the use of steel wire injection technology in the seat backrest part of Tesla Motors. This technology combines steel wire with plastic injection molding to enhance the stability and comfort of the backrest. The specific production process is as follows: Steel wire pretreatment: the steel wire used shall be pretreated first. This includes cleaning, removing surface grease, coating rust inhibitor and other steps to ensure good surface quality of steel wire and improve adhesion to plastic. Plastic melting:
-
hello everyone! The attachment is the concealed outer handle of Tesla car door. The handle is also keyless. Suitable for front and rear door handle selection and layout. At present, the electric car of Confidence basically adopts the structure of hidden external handle, and the accessories contain the detailed structure. I hope it can be helpful to students or friends in need. Thank you! If you have any questions, please contact
-
Structure of wheel drive unit of Tesla electric vehicle: specifically, three-phase AC induction motor includes stator and rotor. The stator is composed of a stack of steel laminations, and the rotor is also composed of a stack of steel laminations. Copper conductor bars are evenly distributed on the circumference. The rotor is installed on the central shaft, and both ends of the central shaft are supported by bearings.
-
The 21700 cylindrical power battery used by Tesla New Energy Vehicles is currently the battery with the highest energy density and the lowest cost among the batteries that can be mass produced. In the future, a large number of domestic production will be carried out with an energy density of 300Wh/kg. The 21700 battery is composed of shell, lug, positive sheet aluminum foil, positive material, negative sheet copper foil, graphite, diaphragm, electrolyte and other parts. Each model in the figure is introduced. The 21700 Tesla power cylinder power battery can be used for battery production reference and related article illustration, demonstration and application in various new energy vehicles, battery materials, power battery recycling and other fields. Include ST
-
Thermo magneto is a new type of power equipment invented by Nikola Tesla according to the magneto thermal effect. The model version is solidworks2012, and the general format step is backed up. Any 3D software can be opened. Welcome to download and collect
-
This device is a kind of bladeless turbine driven by fluid shear force, which is called bladeless turbine because it applies boundary layer effect instead of using fluid to directly impact turbine blades; When the liquid flows in and out, the fluid is affected by the viscous force, which will form a very thin boundary layer at the edge of the pipe wall or other objects. In the boundary layer, the velocity of the fixed surface is 0, and the farther away from the surface, the greater the velocity. Using this effect, a group of disks can be driven by a high-speed liquid; The model is displayed for inventor2015 3D software, and the inventor parts, igs models are uploaded
-
-
-
-
-
The drive system of electric vehicle is composed of lithium battery, motor controller, permanent magnet synchronous motor, etc. The battery, drive motor and controller generally need cooling. TESLA adopts a closed forced cooling cycle system
-
-
-
-
-
-
This scheme uses the Tesla M3 control arm camera to detect welds, and Schneider camera is selected as the camera. The above scheme is to detect the welds of welded products. The 3D camera can be used for 360 degree all-round detection to ensure that there is no missing detection position of the product. The product is an automobile product, and the product quality needs to be strictly controlled. If the detection is unqualified, the code on the product can be identified by the production equipment and traced to the welding station of the previous process, so as to control the product quality from the previous process, To prevent quality accidents of products in batches, the camera is installed on the robot, and the product is clamped on the rotating station. The robot and product rotation are the same during detection
-
-
-
-
-
-
-
-
-
-
-
-
The brake is a device that can slow down, stop or keep the moving parts (or moving machinery) in a stopped state. It is a mechanical part that stops or decelerates moving parts in machinery. It is commonly known as brake. The brake is mainly composed of brake frame, brake parts and control devices. Some brakes are also equipped with automatic adjustment devices for brake clearance. In order to reduce the braking torque and structural size, the brake is usually installed on the high-speed shaft of the equipment, but large equipment with high safety requirements (such as mine hoist, elevator, etc.) should be installed on the low-speed shaft near the working part of the equipment
-
-
-
-
-
-
-
-
-
-
BlockWerx is a professional, full-featured, picture management based management program for block/DWG graphics designed for AUTOCAD users, supporting network drivers
-
S_Prefabricated I-Saddle roof with opening
