-
Since the product has very strict requirements on the position of the glue inlet, and the product surface cannot have glue inlet marks or thimble marks, this set of mold has quoted the structure of the flip chip mold. According to the structure of the product, this set of mold has also quoted the secondary ejection structure. I hope that we can improve our colleagues to provide help, learn together and make progress together
-
The secondary ejection mechanism ZZ1695 can be divided into the following three categories: first, the secondary ejection mechanism of single ejector plate combination, second, the secondary ejection mechanism of double ejector plate combination, and third, the pneumatic/hydraulic secondary ejection mechanism
-
The drawing is a 3D and 2D drawing of the screw tooth products in the common beverage cover. The classic part of the drawing is that the screw tooth is forced off rather than twisted. There are ribs inside the cover, which cannot be forced off directly. The ribs need to be demoulded first and then the screw tooth is removed. This is a secondary ejection structure. I hope this drawing can provide some inspiration for peers to solve the problem of this kind of mold. Thank you
-
This is a set of commonly used secondary ejection mold structure. There is a small undercut inside the product. Secondary ejection has requirements for materials. Generally, the materials should be soft and have deformation space, so that the undercut of the mold can be removed. This belongs to this kind of product. Let's have a look! Thank you
-
Cad drawings for electrical primary and secondary principle design of switching station
Design drawings of switching station, including: secondary schematic diagram of outgoing cabinet, secondary schematic diagram of PT and arrester cabinet, secondary schematic diagram of bus lift cabinet, secondary schematic diagram of incoming cabinet of transformer power supply, secondary schematic diagram of bus coupler cabinet, DC system panel diagram, central signal schematic diagram, DC system schematic diagram, etc.
-
A set of primary and secondary system diagram of the switching station of the Trade City
This drawing is the primary and secondary diagram design of a trading city switching station. The contents of the drawing include: high voltage primary system diagram, measurement and control protection device and switch cabinet intelligent control device configuration diagram, DC panel schematic diagram, flash alarm device wiring diagram, feeder cabinet control protection signal circuit schematic diagram, etc.
-
-
-
-
The gripper is provided with a screw hole for installing the gripper. As long as the gripper is properly replaced according to the shape of the captured part, various parts can be captured. In addition, since the gripper is opened and closed in parallel, parts with the same shape and slightly different size can also be grasped by the same manipulator
-
This set of mold is a very typical design drawing of secondary ejection mold. There is a circle of undercut inside the product, and the demoulding mechanism is not in enough position. In order to make this product, the mold design adopts the structural design of secondary ejection, so that the product can meet the customer's requirements
-
This is a set of injection mold design drawings for the upper and lower lids of the laser lamp. The mold needs secondary ejection. The rear mold has an inclined roof, the seat lengthens and shortens the length of the inclined roof, and the buckle chicken controls the secondary ejection. The four sides have side lock positioning, a single nozzle hot runner, and the front mold opens and vents. The drawing file is UG8.5, which can be edited without parameters. It is only for reference and learning. Welcome to download
-
Canon printer key injection mold, cavity 1 * 4, this product is made of ABS, shrinkage rate 1.004. The front and rear molds are inlaid with mold core, and the cold runner is used to build the bottom gate for glue injection.. The mould is mechanically ejected and spring is reset. The secondary ejection structure is used to force off the internal buckle
-
#Board 1 and board # 2 first move down together for a distance to make room for the round pin to move to the right. Board # 1 and board # 2 are separated, and the small sliding piece in the buckle box moves to the left to counter the upper buckle lever. During mold closing, because the small sliding piece in the buckle box is against the upper buckle lever, the # 1 and # 2 plates are closed first, then the lower buckle lever is used to push the small sliding piece to the right, and the # 1 and # 2 plates are closed together. This type of mechanical buckle machine uses a small mold. In a large mold, too heavy a mold will crack the half round buckle of the lower buckle machine rod
-
The mold design of small lid products for daily necessities has comprehensively applied the professional foundation and professional course knowledge to design. The design surface is smooth and complete. The file includes the STP format, which is the general format of 3D software. It can be edited and does not contain parameters. You are welcome to download the design technology for discussion, but it cannot be used for commercial purposes
-
Because injection mold and die-casting mold need secondary ejection in the special demoulding process, at this time, a secondary ejection mechanism is required to complete its function. The second ejection can smooth the ejection process and avoid product defects during ejection
-
This set of mold is the mold for rearview mirror base, with mold cavity 1 * 1, and two plates of cold runner submerged gate for glue injection. The front mold cylinder is inclined to core pulling in the tunnel, and the lateral cylinder is used for locking. 3 lifter structures for rear formwork. The front and rear moulds are inserted with mould core, the product is mechanically ejected, and the spring is reset. Second ejection and first reset structure are adopted
-
The data is that there are two undercuts on both sides of the product of the twice ejecting mechanism of the injection mold, and the inclined ejecting block is required to eject. Two push tubes are added in the middle to prevent the product from deformation and displacement when the inclined ejecting blocks on both sides eject. The top block is driven by the iron pull hook to realize two times of ejection, download if necessary
-
In plastic molds, we often encounter molds that have strict requirements on the mold opening sequence, so we must use a mechanical shutter (mechanical locking, safe and reliable), which is often used in export molds. This mechanical shutter belongs to the secondary ejection type, and can also be used as a buckle machine, with different installation and different functions
-
This is the design of a secondary ejection injection mold with a pipe structure. The mold has a secondary ejection structure, and the first plate pushes the product to move a certain distance. The structural design of using the ejector pin to eject again is very classic and practical, and has reference and learning value
-
-
-
Secondary principle design and construction drawing of 10kV switching station
For the secondary part design of a 10kV switching station in Beijing, Nanzi protection PSL600UK series dual network communication and VS1 circuit breaker are selected. It mainly includes the secondary principle design of incoming and outgoing line cabinet, bus coupler cabinet, isolation cabinet and PT cabinet. I hope you like it
-
A complete set of secondary drawings of K385 box type switching post
This project is the electrification reconstruction project of Hengfeng Nanping South Section of Fengfu Line, and the secondary drawing design of K385 box switching post. There are many drawings, mainly including the secondary schematic diagram and terminal wiring diagram of the switchgear cabinet. I hope you like it.
-
-
-
-
-
This is a set of injection mold drawings for the right middle guard board framework. The mold cavity is 1+1, shrink 1.0055, the mold embryo is left intact, the second ejection is pulled with the cock control cylinder to pull the ejector pin plate, there are inclined jacks and sliding sliders, and the hot runner needle valve is used to inject glue. The drawing file is incomplete, and you can refer to the structure. The version is UG8.5, editable, without parameters, welcome to download
-
The structure of the multi hole secondary ejection mold for the full circumference slider of the car keys is relatively simple. It should be noted that the surrounding guide bars and the window of the wall should not have rough edges. Since the guide bars of the wall of the product cannot be drawn, the similar car keys need to use the secondary ejection structure. Ensure smooth ejection of products
-
A mold is a tool that uses its specific shape to form products with a certain shape and size. Various moulds are widely used in various material processing industries. For example, sand molds or die-casting molds used for metal casting, forging molds used for metal pressure processing, cold pressing molds and other molds. The overall requirement for the mold is that it can produce public owned products that meet the use requirements in terms of dimensional accuracy, appearance, physical properties, etc. From the perspective of mold use, it requires high efficiency and simple automatic operation; From the perspective of mold manufacturing, it requires reasonable structure, easy manufacturing and low cost. Mold affects the quality of products
-
-
Schematic diagram of 10KV switching post secondary electrical cad of a company
This drawing is the schematic diagram of the secondary electrical cad of a company's 10KV switching post, including various electrical schematic diagrams, electrical design instructions, layout drawings and material lists, wiring diagrams of each unit, layout drawings of each unit, etc., which can be downloaded for reference.
-
The switching station is also called the outer box, with the appearance of 3700x1050x2300 assembly structure, the base is painted after welding, and the top cover is painted after welding; The parts are assembled into a frame and then assembled together with the base and top cover. Material: 304 stainless steel, painted,
-
The utility model discloses a manipulator with replaceable gripper parallel opening and closing, which relates to the technical field of mechanical production automation, including a gripper, a gripper movable mounting block, an upper gripper body, a lower gripper body, a drive disk shaft, a drive disk shaft positioning attachment, a coupling, a low-speed motor and a mechanical gripper mounting bracket, wherein the drive disk shaft positioning attachment includes a bearing, a cup, a shaft sleeve Round nut, special stop washer for round nut and sealing end cap. The extension shaft of the low-speed motor is connected with the shaft end of the drive disk shaft through a coupling. The shaft section of the drive disk shaft is installed in the inner hole of the lower clamping jaw through a bearing and its positioning accessories. The disk end of the drive disk shaft, the upper clamping jaw body, the lower clamping jaw body and the clamping jaw
-
The hand claw method enables it to complete the corresponding work. The manipulator shown in the figure is a structure that can meet this requirement. Its gripper moves in parallel. In addition, when the cylinder piston extends, the gripper opens, and when the piston returns, it grabs the parts
-
The 3D mold structure of the car knee airbag cover plate inclined jacking and the push block secondary ejection is slightly complicated, and a little care has been taken in the design. For example, an inclined jacking is added at the bottom of the push block, and a push block is added at the position where the slider is broken. Because the slope of the A side of this product is increased, Since the inclined jack needs to be forced into the air at the bottom of the pushing block, so that the pushing block and the inclined jack are easy to move during the forming process, we added a shovel foundation on the male die insert to avoid the displacement of the inclined jacking pushing block during the production process
-
Because injection mold and die-casting mold need secondary ejection in the special demoulding process, at this time, a secondary ejection mechanism is required to complete its function. The second ejection can smooth the ejection process and avoid product defects during ejection
-
The mold drawing is a plastic part of a car logo accessory, 2+2. The product uses the hot runner to turn to the big water port to inject glue on the inclined top. The buckle of the rear mold part of the product is used to make the rear mold line position and the rear mold inclined top. The mold action: the parting surface is opened, the ejector rod is ejected, and two sets of ejector plates go up at the same time. The buckle machine controls the ejection, and when the set stroke is reached, the first ejection is not moved, and the second ejection continues to be ejected, The ejector plate is reset by a forced pull back mechanism, and the drawing file structure is clear, which can be used for reference
-