Technical disclosure of foundation safety construction

Uploaded on: 2021-12-12 16:28:12 come from: Landscape / Landscape construction management / Construction technical disclosure

zero

5 points

1. Before starting excavation, the safety officer must conduct technical disclosure, and the operator can only operate after correctly using safety protection articles. 2. Operators shall understand the classification of soil quality and adopt different construction methods according to different categories. 3. The excavated earthwork shall be sloped or supported according to the requirements of regulations according to the soil quality, groundwater level, excavation depth and the foundation where the excavation is located, so as to ensure that no collapse accident occurs during excavation.

Technical disclosure for safe construction of foundation - Figure 1

Technical disclosure for safe construction of foundation - Figure 2

Technical disclosure for safe construction of foundation - Figure 3

Technical disclosure for safe construction of foundation - Figure 4

Technical disclosure for safe construction of foundation - Figure 5

Click to download the source file now

Special statement: This material belongs to the sharing uploaded by users Downloaded content, only for learning, not for commercial use. If there is any copyright problem, please timely contact Station delete!

Collection

WeChat code scanning and sharing

Click to share

Related recommendations

Technical disclosure of foundation and foundation works
Before pipe laying, the sundries in the pipe pit shall be cleaned, and the concrete flat foundation shall be cleaned. Then snap the pipeline centerline on the flat foundation and recheck the elevation of the flat foundation surface.

Topic: Technical disclosure of foundation waterproof Technical disclosure of foundation concrete Technical disclosure of concrete foundation
Earthwork safety technical disclosure of foundation and foundation works
Manual excavation shall be carried out layer by layer from top to bottom. The distance between the front and rear operators shall not be less than 2~3m. The soil stacking shall be 1m away and the height shall not exceed 1.5m. Rock climbing or digging under boulders is strictly prohibited. Sufficient lighting shall be provided at night

Topic: Technical engineering contract Technical disclosure of exterior wall decoration engineering Technical code for high fill foundation
Safety technical disclosure of a foundation and foundation earthwork
This document is the safety technical disclosure of the foundation and foundation earthwork of a certain company. The contents are complete and can be downloaded

Topic: Construction scheme of earthwork disclosure Technical engineering contract Technical disclosure of exterior wall decoration engineering
Safety technical disclosure of a foundation and foundation vibration pile driver and extractor
This document is the safety technical disclosure of a foundation and foundation vibration pile driver and extractor. The contents are complete and can be downloaded

Topic: What technical safety disclosure Safety disclosure of foundation construction Foundation treatment technology
Safety technical disclosure of manual dug pile in foundation and foundation works
This document is the safety technical disclosure of manual hole digging piles for foundation and foundation works. The contents are complete and can be downloaded

Topic: Safety technical disclosure of manual hole digging Manual hole digging pile Technical disclosure of manual hole digging pile concrete pouring
Safety technical disclosure of bored piles for foundation and foundation works
This document is the safety technical disclosure of bored cast-in-place pile of foundation and foundation engineering. The contents are complete and can be downloaded

Topic: Safety technical disclosure of bored pile concrete Bored cast-in-place pile and foundation construction Safety technical disclosure of rotary excavation cast-in-place pile
Open cut foundation engineering foundation treatment safety technical disclosure. doc

Topic: Safety technical disclosure of derrick foundation Basis for safety technical disclosure Basis for safety technical disclosure
How to improve Foundation Construction technology of engineering in modern housing construction
In recent years, the scale of construction projects in China has been constantly expanding, and the construction quality of construction projects has also been constantly improving. However, in the actual construction process, especially in the construction of foundation works of construction projects, there are still some areas that need to be improved, so the relevant departments should strengthen the improvement of their construction technology and technology.

Topic: Building construction foundation Housing construction Soft soil foundation treatment technology for building construction
Construction technology pile and Foundation engineering design
Precast reinforced concrete piles, cast-in-place concrete piles, other piles, foundation and slope treatment

Topic: Technical disclosure of brickwork foundation of construction engineering Paper on Foundation and Foundation Accidents of Construction Engineering Construction Engineering Technology and Design
Analysis on technical disclosure of foundation concrete construction
The foundation of the office building is a cushion cap, ground beam, raft, and the basement is a full shear structure. The foundation raft is 0.55M thick, of which the foundation concrete is about 750m ³, the design strength is C35, the impermeability grade is S6, and it is required to pour it to the post cast strip at one time. The horizontal construction joint of the shear wall should be left until the raft surface turns up 300mm (that is, half of the water stop steel plate), and no construction joint should be left.

Topic: Technical disclosure of external wall insulation Analysis on technical disclosure of building construction Technical disclosure of concrete construction
Technical disclosure of open cut foundation concrete construction
The concrete shall be designed with multiple groups of mix proportion according to the design requirements such as strength grade, durability, raw material quality, construction technology, changes in environmental conditions, etc. The mix proportion selection experiment should be carried out in advance, leaving enough time for mix proportion adjustment

Topic: Technical disclosure of open cut tunnel construction Technical disclosure of concrete foundation construction Technical disclosure of foundation concrete construction
Technical disclosure of independent foundation construction of a project
（1） After the cleaning and foundation trench inspection of cushion pouring, the surface soil and disturbed soil shall be removed, and no ponding shall be left. The cushion concrete construction shall be carried out immediately. The cushion concrete must be vibrated and compacted, and the surface shall be flat. It is strictly prohibited to dry the foundation soil. （2） After the reinforcement binding cushion is poured and the concrete reaches 1.2MPa, the surface snap line is used to bind the reinforcement. The reinforcement binding is not allowed to be missed. The hook part of the column joint bar must be bound at 45 ° with the bottom plate reinforcement. The connection points must be all bound. The first stirrup must be bound at 5cm from the bottom plate, and the last stirrup must be bound at 5cm from the top of the foundation as the elevation control reinforcement and positioning reinforcement, Another locating bar shall be bound at the top of the column joint bar. After the upper and lower stirrups and locating stirrups are bound, the column joint bar shall be adjusted in place and temporarily fixed with a cross shaped wooden frame, and then the remaining stirrups shall be bound to ensure that the column joint bar is not deformed or out of shape. The two locating bars must be replaced after the foundation concrete is poured. After the reinforcement is bound, plastic cushion blocks of the protective layer shall be placed at the bottom and side. The thickness is the design thickness of the protective layer, and the spacing between the cushion blocks shall not be more than 100mm (determined according to the design reinforcement diameter) to prevent the common quality problems of exposed reinforcement. Pay attention to the protection of finished steel bars, and do not collide with the steel bars at will, causing displacement of the steel bars. （3） Formwork installation shall be carried out immediately after the completion of formwork reinforcement binding and relevant professional construction. Small steel formwork or wood formwork shall be used for the formwork, and the scaffold pipe or timber shall be used for reinforcement. When the slope of conical foundation is less than 30 °, inclined formwork shall be used for support, and bolts shall be used to tighten the bottom plate reinforcement to prevent it from floating up. Ventilation and vibration holes shall be set at the upper part of the formwork. When the slope is less than or equal to 30 °, steel wire mesh (spacing of 30cm) shall be used to prevent the concrete from falling down, and cross logs shall be set at the upper opening to control the position of reinforcement. It is not allowed to impact the formwork with heavy objects, and it is not allowed to erect scaffolding on the formwork of hanging wall to ensure that the formwork is firm and tight.

Topic: Technical disclosure of independent foundation formwork construction Technical disclosure of independent foundation concrete Technical disclosure of building independent foundation
Technical disclosure of foundation construction of construction elevator
XX Huafu Residential Community Phase II is located in the Jin'an Huafu Residential Community Phase II plot on the west side of Dongfangyi Building, Yanjiangbei Road, Chenghudi, Wuhua Shuizhai Town, Meizhou City, Guangdong Province. This project is a high-rise building, consisting of three connected buildings A, B and C, which form 3 # building, with 31 floors and a building height of 98.3m; Building C has 25 floors, with a building height of 80.3m, a total land area of about 5696.89 ㎡, and a building base area of 3942.20 ㎡. The plan of the basement building is roughly rectangular, with a plan size of 33m × 126.25m. The standard floors of the tower are connected in three criss cross shapes, which is the highest building under construction in Meizhou. According to the actual situation on site, this project can only install construction elevators on the south side of the site. According to the construction volume of the secondary structure of this project, it is planned to install two construction elevators, the model of SC200/200, which are respectively arranged on the south side of buildings A and B.

Topic: Technical disclosure of elevator construction Construction elevator foundation Technical disclosure of foundation cushion cap construction
Technical disclosure record of foundation reinforcement construction
The steel bar calipers are used to limit the binding of the plate reinforcement. The negative bending moment reinforcement on the upper layer of the plate is not bent leg erection, but is supported by the steel bar stirrups.

Topic: Rebar construction disclosure Steel bar safety technical disclosure record Technical disclosure record of foundation concrete
Technical disclosure data of tower crane foundation construction
This disclosure is applicable to the tower crane foundation construction of Shunyi Pinggezhuang Limited Price Commercial Housing Lot 4 Project.

Topic: Technical disclosure of tower crane foundation construction Construction technical disclosure data Data Handrail Construction Technical Disclosure
Technical disclosure of tower crane foundation construction - 002
Technical disclosure of tower crane foundation construction - 002 Technical disclosure of tower crane foundation construction - 002 Technical disclosure of tower crane foundation construction - 002 Technical disclosure of tower crane foundation construction - 002 Technical disclosure of tower crane foundation construction - 002 Technical disclosure of tower crane foundation construction - 002 Technical disclosure of tower crane foundation construction - 002 Technical disclosure of tower crane foundation construction - 002

Topic: Technical disclosure of tower crane foundation construction Technical disclosure of tower crane foundation concrete pouring Safety technical disclosure of tower crane foundation concrete
Technical disclosure of foundation formwork construction 1.doc

Topic: Technical disclosure of foundation cushion cap formwork construction Safety technical disclosure of foundation formwork installation Safety technical disclosure of large formwork
Technical disclosure of cushion cap construction (foundation part)
The cushion cap was constructed in October to November, and the flood season of Qingyi River has passed, so the construction is still difficult. The bottom elevations of 10 # and 11 # cushion caps are 1.5m and -4.0m respectively. The excavation depth of foundation pit is 6.7m for 10 # pier and 13.3m for 11 # pier. Among them, 10 # pier is close to the river embankment on the north bank, and 11 # pier is a deep foundation pit. During construction, the expected water level elevation is about 5m, and steel sheet pile cofferdam excavation is adopted through scheme comparison.

Topic: Technical disclosure of foundation cushion cap construction Technical disclosure of cushion cap construction of first-class highway Technical disclosure of cushion cap concrete pouring construction
Technical disclosure for foundation construction of masonry works
Masonry should be built by the "four one one" bricklaying method (i.e. one shovel of ash, one brick, one extrusion, kneading, and adding -- knife head joint mortar). When laying mortar, it must be squeezed; The paving length shall not exceed 5 OOmm. The vertical mortar joint shall be poured first, then the water mortar joint shall be paved, and the first joint shall be plastered before masonry.

Topic: Technical disclosure of masonry structure construction Masonry construction technical disclosure ppt Technical disclosure of aerated concrete masonry construction
Technical disclosure of open excavation foundation reinforcement construction
Operation condition 1. Before masonry, the wall base shall pass the acceptance; The floor, ash, debris and the higher part of the gangue wall shall be cleaned. 2. Snap the horizontal line of+500mm elevation, the vertical side line of gangue wall and the position line of the door on the structural wall and column. 3. Prepare the ground cushion; At the bottom of the block wall, build a clay brick or perforated brick wall or cast concrete foundation belt with skirting board height.

Topic: Rebar construction disclosure Technical disclosure of raft foundation reinforcement Capping beam construction disclosure
Architecture Foundation Technical specification for reinforcement

Specification for reinforcement
Technical disclosure record of foundation drilling exploration construction
1. Set out in the layout plan of drill hole location, and nail small stakes or sprinkle lime spots on the hole location. 2. Align the tip of the feeler rod with the hole position, then put the penetration hammer on the drill rod, straighten the drill rod, pull up the penetration hammer, make it fall freely, the hammer distance is 50cm, and drive the feeler rod vertically into the soil layer. 3. The number of blows shall be recorded. The drilling line shall be driven into the soil layer for 30cm, and the number of blows shall be recorded. It shall be executed according to the foundation drilling exploration record (Table C5-7). 4. Pull out the drill rod: bind the drill rod with lead wire, leave the looper, insert the iron pipe into the sleeve, pull out the drill rod using the lever principle, and cover the hole with a brick after pulling out. 5. Displacement: move the feeler rod to the next hole position to continue drilling. 6. Sand filling: the drilled drill hole shall be filled with sand after the quality inspector and foreman check the hole depth and record. When filling sand, steel bars can be used to tamp once every 30cm. 7. Sort out records: number the holes according to the sequence of holes, fill the blow counts in the unified form, write clearly, and file after being signed by the technical director, quality inspector, and drilling personnel. 8. If the project is to be constructed in winter, each hole shall be covered with insulation materials in time, and it shall not be opened in a large area to prevent the foundation soil from freezing.

Topic: Drilling exploration for foundation treatment Technical code for drilling exploration of foundation Detailed explanation of construction technical disclosure records
Technical disclosure record of electrician safety construction
The electrical equipment in the electric box shall be complete and free of defects, with a special leakage protection switch. One leakage switch must control one socket according to the standards of the Ministry of Urban and Rural Development.

Topic: Electrician safety technical disclosure record Safety technical disclosure of pile driver Safety technical disclosure of tower crane workers
Technical disclosure for safety construction of demolition works
Personal protective equipment and safety protection measures must be correctly used for rebar binding, and protective sheds or other isolation facilities shall be provided at dangerous entrances and exits for up and down cross operations.

Topic: Safety technical disclosure Demolition safety technical disclosure Overview of construction technical disclosure project
Technical disclosure for safe construction of masonry works
During masonry, bricks can be laid at the corners and joints according to the number of bricks, and then the middle part can be laid with the alignment line. The first brick shall be laid according to the bottom width line of the foundation. The brick foundation of internal and external walls shall be built at the same time. If the masonry cannot be built at the same time due to special circumstances, the diagonal rubbing shall be reserved, and the length of the diagonal rubbing shall not be less than 2/3 of the height of the diagonal rubbing,

Topic: Safety technical disclosure of pile driver Safety and technical disclosure of building construction Safety technical disclosure of brick masonry works
Technical disclosure of roof engineering safety construction
The binding of reinforcement shall meet the requirement that the intersection of reinforcement shall be firmly bound with iron wire, and the load-bearing reinforcement must not be displaced. The distance between the end of the overlapping length of the rebar binding joint and the rebar bend shall not be less than 10 times of the rebar diameter, and the joint shall not be located at the maximum bending moment of the member. The steel bar lap joint shall be firmly tied with iron wire at the center and both ends. The binding joints of stressed steel bars shall be staggered. The sectional area of stressed steel bars in the binding joints shall not exceed 25% of the total sectional area of stressed steel bars in the tensile area and 50% in the compressive area.

Topic: Overview of construction technical disclosure project Technical disclosure of external wall insulation Technical disclosure of exterior wall putty
Technical disclosure for safe construction of formwork works
The specification and quality of materials used for arch support shall meet the requirements. During the fabrication of truss arch, each member shall be made of wood with strong material, no damage and low humidity. During the fabrication of the wood clip arch frame, the length of the wood plate shall be matched well, the longitudinal joints shall be staggered, and the spacing and joints of each section shall meet the use requirements. The panel clamp shall be fixed with bolts at intervals, and the rest shall be fixed with iron nails and arch ribs.

Topic: Safety technical disclosure Technical disclosure of construction formwork Safety technical disclosure of large formwork
Second Construction Examination Materials Lesson 10 Foundation Engineering construction technology and quality management 2

Topic: Engineering construction technology and management Highway construction technology management examination Examination of Highway Construction Technology and Management
Technical disclosure of mechanical drilling safety construction of cast-in-place pile foundation
The construction site shall meet the requirements of drilling machine operation. The foundation in dry land area shall be flat and solid; Island building method shall be adopted in shallow water area; Water operation platform must be set up in deep-water rivers and lakes. The operation platform shall be designed according to the construction load, water depth, water flow and engineering geological conditions, and its elevation shall be more than 70cm higher than the highest water level during construction.

Topic: Safety technical disclosure of pile foundation works Technical disclosure of pile foundation construction Technical disclosure of pile foundation concrete
GB50202-2002 Buildings Foundation
This document is GB50202-2002 building foundation, which is detailed and clear, and has high reference value. It can be downloaded for reference.

Topic: Building foundation Code for Building Foundation 2012 Code for Building Foundation 2016
Foundation Design GB50007-2002
This data is: foundation design GB50007-2002, which is detailed and can be used for reference.

Topic: Building foundation Code for design of foundation Building foundation construction
Safety technical disclosure of 220kV framework foundation construction
The ground design elevation (± 0.000) of 220kV architecture foundation is 118.180m. C30 concrete is used for foundation, C35 fine aggregate concrete is used for secondary grouting, C15 concrete is used for foundation cushion, and the thickness of foundation protective layer is 50mm.

Topic: Safety technical disclosure of tower crane foundation construction Safety technical disclosure of derrick foundation Safety technical disclosure of foundation formwork removal
Safety technical disclosure of 220kV equipment foundation construction
This data is the safety technical disclosure of 220kV equipment foundation construction, and a total of 220kV equipment support foundation construction safety technical disclosure pages are detailed for reference.

Topic: Equipment safety technical disclosure Technical disclosure of equipment foundation construction Technical disclosure of equipment foundation concrete
Safety technical disclosure of equipment support foundation construction
The filling area is within 90m east of the west wall of the 220kV equipment foundation area. Before construction, according to the drawing No. 373-B201S-T0304-01 of Shandong Electric Power Engineering Consulting Institute, 0.5m thick 3:7 lime soil cushion is made under the GIS and equipment support foundation. The cushion extends 0.5m beyond the foundation edge. The cushion is located on the foundation after dynamic compaction, with the characteristic value of bearing capacity fspk=150Kpa; The foundation in the excavation area is located on the bearing stratum (completely weathered granite), and the characteristic value of bearing capacity fspk=250Kpa

Topic: Support safety technical disclosure Equipment safety technical disclosure Technical disclosure of equipment foundation construction
Safety technical disclosure of dynamic compaction foundation construction
This data is the safety technical disclosure of dynamic compaction foundation construction, which is valuable, detailed and can be used for reference.

Topic: Dynamic compaction foundation construction Specification for dynamic compaction foundation Construction scheme of cement road dynamic compaction foundation
Existing buildings Foundation Technical specification for reinforcement

Technical Code for Foundation Reinforcement of Existing Buildings JGJ 123-2000
Hubei Provincial Architecture Foundation technical specifications
The current general technical code for building foundation in Hubei Province. Including: general rules; Terms and symbols; Basic regulations; Geotechnical classification and engineering characteristic index; 14 items including design calculation of natural foundation. Hubei Provincial Department of Construction proposed that Hubei Provincial Department of Construction is under the jurisdiction of Hubei Provincial Department of Construction, and Hubei Institute of Building Science and Technology Research and Design is the main drafting unit. I have the right to forward the electronic version of the specification.

Topic: Technical Code for Building Foundation of Hubei Province Technical Specifications of Hubei Province Hubei Provincial Building Code
Existing buildings Foundation Technical specification for reinforcement
This data is the technical specification for foundation reinforcement of existing buildings, which is detailed and can be used for reference.

Topic: Technical code for building foundation Code for foundation reinforcement Beijing foundation reinforcement
0 Existing buildings Foundation Technical specification for reinforcement
This data is: 0 Technical code for foundation reinforcement of existing buildings, which is detailed and can be used for reference

Topic: Technical code for building foundation Code for foundation reinforcement Beijing foundation reinforcement
On muddy soil Foundation Excavation technology
The proposed site is located in the coastal industrial zone, which is mostly a salt drying field. After years of seawater immersion, the underground sludge layer is thick and lacks bearing capacity. It is a typical soft soil foundation layer. There are great difficulties in both manual and mechanical construction. According to the survey, the surface layer of the site foundation soil layer is about 1.8m filled with soil and plastic clay, and the buried depth is about 1.8-11.7m of marine facies silt, below which is hard plastic clay with good properties.

Topic: Treatment of muddy soft soil foundation Technical code for soil foundation excavation Construction technology of sludge foundation