Technical disclosure of formwork construction in a residential area

Uploaded on: 2020-05-07 11:55:36 come from: electrical engineering / Electrical construction design / Construction disclosure

zero

5 points

Formwork removal (1) Non bearing side formwork shall be removed when the concrete strength can ensure that its surface edges and corners will not be damaged due to formwork removal. (2) The load-bearing formwork can be removed only when the test block cured under the same conditions as the structure reaches the specified strength. (3) During formwork removal, the formwork that is supported first shall be removed later, and the formwork that is supported later shall be removed first. The non bearing part shall be removed first, and the bearing part shall be removed later. The complicated formwork removal shall be prepared in advance. (4) The beam formwork shall be removed from the middle of the span to both ends. (5) In the process of removal, if quality, safety and other problems are found, the removal shall be suspended, and the removal of formwork can be continued after treatment.

Technical disclosure of formwork construction in a residential area - Figure 1

Technical disclosure of formwork construction in a residential area - Figure 2

Technical disclosure of formwork construction in a residential area - Figure 3

Technical disclosure of formwork construction in a residential area - Figure 4

Technical disclosure of formwork construction in a residential area - Figure 5

Click to download the source file now

Special statement: This material belongs to the sharing uploaded by users Downloaded content, only for learning, not for commercial use. If there is any copyright problem, please timely contact Station delete!

Collection

WeChat code scanning and sharing

Click to share

Related recommendations

Tunnel engineering construction Technical disclosure (template)

Topic: Technical disclosure of tunnel construction Tunnel construction technology ppt Case Analysis of Tunnel Construction Technology
Main structure formwork engineering construction Technical disclosure
First, put the four side formworks on the first floor of the column in place and assemble them. Each side is equipped with an internal corner formwork or connecting angle formwork, which is connected alternately.

Topic: Technical disclosure of formwork construction Technical disclosure of main structure construction Construction technical disclosure of main works of building structure
Construction formwork engineering construction Technical disclosure
Template Configuration Template configuration principle: each type of template in each area is configured according to the maximum flow section. 1) Wall formwork Underground part: 15mm thick film covered multilayer wood formwork is used for basement wall, and 2 sections of formwork are configured Above ground part: 15mm thick laminated wood formwork is used for the standard layer wall, and 2 sections of formwork are configured 2) Slab formwork Underground part: configured as per single floor Above ground part: all underground formworks are used above ground, and will be added if insufficient. It is also necessary to add 3 floors, and four floors of floor formwork and support shall be used repeatedly. 3) Roof support Socket type early dismantling frame system shall be selected. The top plate shall be 15mm thick multilayer board, the main keel shall be 100 × 100 square timber, and the secondary keel shall be 50 × 100 timber keel. The distance between poles is 1200 × 1200mm, and the step distance is 1200mm. 4) Stair, door and window opening formwork Standard and non-standard stairs are supported by wood formwork and steel pipes. Steel angle formwork and wood formwork shall be used for door and window opening formwork. Selection and use precautions of isolating agent Check whether the formwork is cleaned in place. Any formwork that does not meet the requirements is not allowed to be used as the main release agent without authorization, and must be notified to the team leader for rectification. Release agent can be applied after verification. Check whether the quality of release agent is abnormal. If there is any abnormality, report it to the team leader and take measures. Unqualified release agent shall not be used. The release agent shall be brushed by a specially assigned person, and it shall be evenly brushed. No omission or flowing trace is allowed. Release agent shall be received when used, and the rest shall be returned to centralized storage to prevent waste and deterioration.

Topic: Technical disclosure of construction engineering is good Technical disclosure of formwork construction Sub item technical disclosure of construction formwork
Template engineering construction Technical, quality and safety technical disclosure
The pier and abutment formwork should be removed before the construction of its superstructure. When removing the formwork and removing the supports and arches, it is not allowed to use violent knocking and strong twisting. After the formwork, support and arch frame are removed, they shall be maintained, sorted and stored properly.

Topic: Technical disclosure of formwork construction Safety technical disclosure of large formwork Safety quality technical disclosure
Template engineering construction Technical disclosure (underground part)
The current ground soil is relatively soft, and foundation treatment is required. During treatment, the plain soil shall be compacted in layers to the position 10cm away from the top surface of the foundation, and the heavy roller shall be used for rolling in layers. Then, 10cm concrete shall be paved on it, and the surveyor shall measure at any time on the site to strictly control the elevation of the foundation top surface. The foundation shall be treated symmetrically to both sides with the location survey center line as the benchmark when it reaches the existing pavement.

Topic: Technical disclosure of formwork construction Technical disclosure record of formwork divisional and subdivisional construction Construction technical disclosure of ventilation and air conditioning works
Formwork of a basement engineering construction Technical disclosure
Contents of disclosure 1. Name of disclosure division (sub division) and subdivisional works: technical disclosure of formwork works 2. Name and number of disclosure implementation standard: current national construction quality acceptance specifications 3. Summary of disclosure contents:

Topic: Technical disclosure of formwork construction Construction technical disclosure of ventilation and air conditioning works Technical disclosure of concrete structure construction
Technical disclosure for formwork construction of comprehensive building
Construction preparation 1. Material requirements (1) Metal trunking and its accessories shall be galvanized stereotyped products. The specification and model shall meet the design requirements. The inside and outside of the trunking shall be smooth and flat without ridges, distortion, edge warping and other deformation phenomena. Product certificate and material certificate shall be provided. (2) Busbars shall be provided with factory certificates and installation technical documents. The technical documents shall include the rated voltage, rated capacity, test report and other technical data. (3) Various connectors, clamps, bolts and washers shall meet the technical requirements and be galvanized products.

Topic: Capping beam construction disclosure Rebar construction disclosure Safety construction disclosure
Technical disclosure of formwork construction of construction engineering
Formwork: 15 thick wood plywood formwork is used for column, 100 × 100mm wood rib, and the spacing is 400-500mm; 15 thick wood plywood formwork is used for beam and plate bottom formwork, and the thick wood square is used for formwork bedding; wood plywood formwork is used for beam formwork measurement, and steel pipe is used as the support frame system. During the formwork construction, when the span of the cantilever plate is greater than 1.0m, the construction shall be arched as per 1/200; Generally, beams with a span greater than 4m shall be arched according to 1/1000 to 3/1000. Before removing the formwork, the test strength of concrete test block shall reach 75%. However, in order to speed up the turnover of formwork, the quick removal system of formwork used in this project is shown in the figure below.

Topic: Technical disclosure of construction formwork Technical disclosure of cushion cap formwork construction Technical disclosure record of formwork construction
Technical disclosure for formwork construction of main structure works
The shear wall and column formwork of the project are supported vertically by 50 × 100 square timber with a spacing of 200, and horizontally by steel pipe Φ 12 through wall screws with a spacing of no more than 500.

Topic: Technical disclosure of main structure construction Technical disclosure of main formwork works Technical disclosure of formwork construction
Technical disclosure of safety construction of formwork project in a community
Slab joint formwork: (1) The width of slab joint is 4 cm, and 50 ㎜× 50 ㎜ square timber or angle steel can be used as the bottom formwork. For those larger than 4 cm, wood plate shall be used as the bottom formwork, and it is better to go deep into the bottom of the plate for 5~10 mm to leave a groove, so that the ceiling can be plastered with mortar for leveling after formwork removal. (2) The plate joint formwork should be supported by wood or steel pipe, or by suspender. (3) The lower part of the support shall be firmly padded with wood plates and wooden wedges, and brick pads are not allowed.

Topic: Technical disclosure of construction formwork Safety technical disclosure of pile workers Safety technical disclosure of tower crane workers
Technical disclosure of formwork construction of the Institute
This document is the technical disclosure of the formwork construction of the research institute project. The document includes: before the removal of the beam and slab formwork, the scaffold board should be laid on the crossbar at the appropriate part of the full scaffold (to meet the operation requirements) to meet the safety needs during the operation and prevent the removed formwork from falling directly from high places. When removing the formwork, the operator is strictly prohibited to stand directly below the removed part, and use a special crowbar to remove the beam and slab formwork. Rough construction is prohibited.

Topic: Capping beam construction disclosure Safety construction disclosure Rebar construction disclosure
Template engineering construction Implement technical disclosure
Surveyors set out the location survey center line of the project. The vertical pole axis is perpendicular to the box girder axis and parallel to the pier column axis. The door opening shall be erected according to the elevation of the door opening bracket, and the door opening scaffold shall be connected with the Mantanghong bent as a whole. The bowl buckle frame pole shall be arranged according to the elevation difference between the bridge and the existing ground, and the upper part of the pole is jacking. Double rows of Φ 35mm steel pipes are laid in the longitudinal direction of the jacking upper bridge, 10 × 10cm square timber is laid in the transverse direction with a spacing of 10cm, and 18mm thick concrete plywood is laid on the large plate as the bottom formwork of cast-in-place box girder.

Topic: Overview of construction technical disclosure project Safety technical disclosure Technical engineering contract
Garden of a residential area engineering construction Organizational design/
1、 Preparation description and basis II. Project characteristics III. Construction site layout description and management organization responsibility division

Topic: Project construction organization design Construction scheme of resettlement area project Construction scheme of residential energy conservation project
Garden of a residential area engineering construction organization design
From site leveling, positioning of buildings and structures, foundation construction, to installation of building components, construction measurement is required to make the size and location of buildings and structures meet the design requirements.

Topic: Landscape engineering construction survey Summary of garden engineering construction training Construction Contract of Landscape Engineering
[Shenzhen] a residential landscape engineering construction chart

Content introduction Drawings include: design description and catalog, general layout, setting out and positioning plan, vertical elevation plan, coordinate positioning plan, pavement plan, landscape sketch layout plan, main road construction drawing, main entrance square construction drawing, fountain square construction drawing, activity square construction drawing, quadrangle pavilion square, atrium square Roof garden construction drawing. 16 CAD files.

Topic: Residential landscape Construction drawing of residential area Full set of construction drawings for residential area
[Guangzhou] residential landscape engineering construction chart

Content introduction Drawings include: general layout, flower bowl standard practice, waterscape construction practice, tree pool construction practice, rest platform construction practice, viewing platform construction practice, characteristic sculpture landscape wall practice, rest platform and seat details, size positioning plan, pavement plan, positioning plan, size positioning plan, elevation pavement index plan Coordinate positioning plan, index general plan and construction details of square timber pavilion. 11 CAD files.

Topic: Residential landscape Construction drawing of residential area Full set of construction drawings for residential area
[Shaanxi] Landscape of a residential area engineering construction chart
Drawings include: drawing list, general layout, general layout setting out drawing, general layout vertical design drawing, general layout paving index drawing, section drawing, general greening description and plant list, general layout arbor planting drawing, general layout shrub planting drawing, pedestrian street landscape setting out drawing, house landscape setting out drawing, central landscape setting out drawing, greening nursery stock specification list, nursery stock list, Leisure pavilion details, wooden bridge horizontal and vertical section, wooden platform details, garden road 1, 2, 3 plan and section details, square brick floor plan and section details, leisure seat plan... 48 drawings. 　　

Topic: Residential landscape Construction drawing of residential area Full set of construction drawings for residential area
Residential landscape engineering construction chart
This project is the construction drawing of the garden landscape project in the residential area. The drawing includes the fixed point setting out drawing of Zone G, Zone H, Zone J, Zone K, etc. The content of the drawing is complete, the expression is clear, and the drawing is rigorous. Designers are welcome to download and use it.

Topic: Landscape design of residential area Residential landscape Landscape construction in residential area
[Kunming] residential landscape engineering construction chart

Content introduction Drawings include: road pavement details, unit entrance pavement details, circular plaza pavement details, dryland fountain pavement details, swimming pool details, pavilion details, scaffolding details, security pavilion details, sports plaza details, iron gate details, entrance lane details, plaza pavement details, underground garage entrance scaffolding details, fence details, flat location drawings Plan guidance drawing. 5 CAD files, 3 JPG drawings,

Topic: Residential landscape Construction drawing of residential area Full set of construction drawings for residential area
[Huizhou] Landscape of a residential area engineering construction chart

Content introduction Drawings include: general layout, featured pavement, featured flower bowl, detailed drawing of manhole, detailed drawing of step step, zoning index drawing, underground garage plan, detailed drawing of iron railings, detailed drawing of dry spraying, detailed drawing of rack, and lighting layout plan. 25 CAD files.

Topic: Residential landscape Construction drawing of residential area Full set of construction drawings for residential area
[Nanjing] Landscape of a residential area engineering construction chart

Content introduction Drawings include: general layout, general layout of basement floor area I, general layout of ground floor, index drawings of each zone, construction details of entrance sentry box, main intersection landscape wall, standard section of fence along the road, entrance fountain square, detailed drawing of wind bell door, railing details, detailed drawing of ramp steps, detailed drawing of sentry box along the lake, detailed drawing of characteristic paving, detailed drawing of tree planting groove The standard section of the wall along the lake, the detail drawing of the pavilion, the floor of the commercial square, the detail drawing of the separation iron gate in the commercial area, the detail drawing of the badminton stand, the detail drawing of the tree pool, the detail drawing of the pedestrian road, the detail drawing of the featured floor, the detail drawing of the badminton court, the detail drawing of the bridge, the detail drawing of the featured waterfall area, the detail drawing of the Tingbu, and the detail drawing of the stepped lawn. 　

Topic: Residential landscape Construction drawing of residential area Full set of construction drawings for residential area
Greening of a residential area in Baotou engineering construction chart

Content introduction This design is a landscape greening drawing for a high-end residential area, including: general layout, plant nursery stock table, detailed layout of zoning plants, and setting out drawing. It has high reference value in plant configuration. 7 CAD files,

Topic: Residential area Construction drawing of residential area Green design of residential area
Greening of a residential area engineering construction organization design
The construction organization design of the greening project of a community includes project overview, construction deployment, schedule, quality and safety measures, main construction processes, construction process frame, and greening construction maintenance technical scheme.

Topic: Project construction organization design Model of greening construction organization design Overall Design of Greening Construction Organization
Small square landscape in residential area engineering construction chart
This document is the construction drawing of the small square landscape project in the residential area, including: plan, detail drawing of the sunlight shed, detail drawing of the entrance sign, detail drawing of the guard room, detail drawing of the landscape colonnade, detail drawing of the sculpture in the center of the square, detail drawing of the square creek, detail drawing of the wooden pavilion, and pavement of the center square. The design is accurate and the content is detailed, which can be downloaded for reference by netizens.

Topic: Residential landscape Design of residential square Construction drawing of residential area
Garden of a residential area engineering construction organization design
The construction organization design of a residential garden project is detailed and rich, which can be downloaded by netizens. 1. A large number of paving and greening have been used to form a lively and natural pavement. Therefore, the quality control of paving and greening should be a key point. 2. Greening construction must be carried out alternately with civil construction. It is very important to coordinate the connection and cooperation of each process to avoid or reduce mutual interference

Topic: Project construction organization design Construction scheme of resettlement area project Construction scheme of residential energy conservation project
some engineering construction Complete design scheme of technical disclosure template
Generally, interval skip driving method or continuous driving method is preferred for CFG pile construction in this project. The specific construction method is determined by field test.

Topic: Technical disclosure of formwork construction Template of highway construction technical disclosure scheme Construction technical scheme disclosure
Public rental housing template of Binhe New Residence engineering construction Technical disclosure
Formwork design: according to the project structure type and structural characteristics, according to the specific site construction conditions, the formwork splicing form is designed in advance to determine the plane layout, specification, quantity, arrangement size of the formwork, splicing and reinforcement form used for column head formwork, beam slab support spacing, beam column node, primary and secondary beam node connection form. Check the strength, rigidity and stability of formwork and support. The quantity of formwork shall be divided according to the flow section during formwork design to determine the reasonable preparation quantity of formwork.

Topic: Construction Contract of Public Rental Housing Project Technical disclosure of formwork construction Technical disclosure of project construction&
Fourth floor frame shear wall formwork engineering construction 6 pages of technical disclosure
1. According to the structural type and characteristics of the project and the site construction conditions, the formwork shall be designed to determine the plane layout of the formwork, the specifications, quantity and arrangement dimensions of the vertical and horizontal keels, the type and spacing of the column hoops, the support spacing of the beam and slab, and the details of the beam column nodes, primary and secondary beam nodes. Check the strength, rigidity and stability of formwork and support. Draw a complete set of template design drawings (template layout plan, block drawing, assembly drawing, reinforcement detail drawing, node detail drawing, part processing drawing and splicing processing drawing of non stereotyped parts). The quantity of formwork shall be divided according to the flow section during formwork design, and comprehensive research shall be carried out to determine the reasonable quantity of formwork.

Topic: Technical disclosure of formwork construction Construction technical disclosure of ventilation and air conditioning works Technical disclosure of concrete structure construction
Technical disclosure of scaffold and formwork construction
The ramp for up and down passage shall be set up synchronously for the floor scaffold, and a non slip wooden strip shall be set every 250~300mm. The width of pedestrian ramp shall not be less than 1m, and the gradient shall be 1:3. The width of the material conveying chute shall not be less than 1.5m, and the gradient shall be 1:6.

Topic: Scaffolder safety technical disclosure Technical disclosure of external wall insulation Technical disclosure of exterior wall putty
Records of technical disclosure of formwork construction
The contact surface between formwork and concrete shall be cleaned and painted with isolating agent, but the isolating agent that affects the structural performance or hinders the construction of decoration works shall not be used

Topic: Technical disclosure record of formwork construction Technical disclosure record of water and electricity installation Technical disclosure record of earthwork excavation construction
Technical disclosure of foundation formwork construction 1.doc

Topic: Technical disclosure of foundation cushion cap formwork construction Safety technical disclosure of foundation formwork installation Safety technical disclosure of large formwork
Technical disclosure of main (second floor) formwork construction
The quantity of formwork shall be divided according to the flow section during formwork design, and comprehensive research shall be carried out to determine the reasonable quantity of formwork.

Topic: Technical disclosure of main construction Technical disclosure of cushion cap formwork construction Technical disclosure record of formwork construction
Technical disclosure of tall formwork support construction
According to the provisions on the scope of dangerous divisional and subdivisional works in the Measures for the Safety Management of Divisional and Subdivisional Works with High Risks (JZ [2009] No. 87): the formwork support height of concrete components at the construction site of the construction project exceeds 8m, or the erection span exceeds 18m, or the total construction load of cast-in-place slab components exceeds 15KN/㎡, Or the formwork support system with the linear load of cast-in-place beam components greater than 20KN/m.

Topic: Technical disclosure of tall formwork construction Technical disclosure of steel support construction Technical disclosure of support beam construction
Preparation of technical implementation disclosure of formwork construction
When using fastener type steel pipe support as formwork support, the support erection shall meet the following requirements: (1) When the extension length of the adjusting screw of the adjustable base exceeds 30cm, reliable fixing measures shall be taken. (2) The four sides and the middle of the Mantanghong bracket shall be provided with a longitudinal cross bridging every four rows of vertical poles, which shall be set continuously from the bottom to the top. (3) A horizontal cross bridging shall be set every four rows of vertical poles at both ends and in the middle of the full hall scaffold higher than 4m from the top floor down every two steps. (4) When a single vertical pole is used for the beam formwork support, the vertical pole shall be set at the center line of the beam formwork, and its eccentricity shall not be greater than 2.5cm. (5) The vertical and horizontal spacing of the upright shall comply with the provisions of the construction design, and shall be corrected after each step of support erection; The upright shall be vertical, and the vertical deviation of 2m height shall not exceed 1.5cm; After each step of support erection, it shall be corrected.

Topic: Technical disclosure of construction formwork Technical disclosure of concrete construction Preparation of construction technical disclosure data
Masonry construction technical disclosure (standard formwork)
Material requirements (1) The steel pipe material must be qualified, with factory certificate, and must meet the design requirements when there are special requirements in the design; (2) Appearance inspection: the steel pipe surface is free of serious corrosion, uniform wall thickness, uniform weld seam, cracks, burrs, sand holes, ridges, dents and other defects; (3) The internal and external diameters and wall thickness of steel pipes shall comply with national standards when measured with vernier calipers; (4) The locking nut shall be in good shape, with clear screw thread, and free of warpage, deformation and other defects; (5) The metal plate thickness of iron lamp holder box, switch box, etc. must meet the requirements of the national standard or North China standard atlas.

Topic: Technical disclosure of construction formwork Technical disclosure of external wall insulation Technical disclosure of exterior wall putty
Road and pipe network engineering construction Technical disclosure
Gravel and sand cushion shall be evenly mixed and then paved. During paving, leveling shall be carried out while paving, and plate vibrator shall be used to vibrate and compact the cushion surface.

Topic: Download the technical disclosure manual of road engineering construction Technical measures for road engineering construction Technical disclosure of project construction&
Rebar item engineering construction Technical disclosure
For the full-length longitudinal reinforcement of frame shear beam or slab, the surface reinforcement shall be lapped at 1/3 of the midspan, and the bottom reinforcement shall be at the support; The lap length shall be in accordance with the design drawings, and if there is no design requirement, the lap length shall be in accordance with the specification requirements. When the secondary beam is the same height as the main beam, the main reinforcement of the secondary beam should be placed on the main beam, and the height of the overlapping reinforcement should be deducted from the main reinforcement stirrup to prevent the surface reinforcement protection layer from being too small. When the gap between the top of the door and window opening and the bottom of the beam of the external wall is ≤ 300, lintel reinforcement shall be placed at the top elevation of the door and window opening, and the opening hoop and beam bottom reinforcement shall be used for connection. The cushion block must also be bound on the side of the beam to ensure the thickness of the beam protective layer. Four beam cushion blocks (the next two and the side two) shall be placed every 1m. The hooks of beam stirrups shall be staggered on the two erection bars, and the corners of stirrups and the intersections of longitudinal bars shall be bound firmly.

Topic: Technical disclosure for construction of reinforcement subdivisional works Technical disclosure of concrete subdivisional works Engineering construction technology
Concrete cushion engineering construction Technical disclosure
Materials and main machines and tools: (1) Cement: No. 325 Portland cement, ordinary Portland cement and slag Portland cement should be used. (2) Sand: medium sand or coarse sand, with silt content not more than 5%. (3) Stone: pebble or crushed stone, with a particle size of 0, 5~3, 2cm, and a silt content of no more than 2%. (4) Concrete mixer, scale, trolley or dumper, shovel, flat shovel, plate vibrator, tumbling barrel or sliding pipe, scraping bar, wood trowel, rubber water pipe, iron chisel, steel wire brush.

Topic: Technical disclosure of cushion concrete construction Construction technology of reinforced concrete engineering Technical disclosure of project construction&
Concrete sub item engineering construction Technical disclosure
(1) Base course treatment: the laitance, loose concrete, mortar, etc. bonded to the concrete base course shall be removed with a chisel, the cement slurry skin shall be brushed off with a wire brush, and then cleaned with a broom. (2) Snap the horizontal control line according to the elevation: measure the cushion elevation downward according to the+50cm horizontal elevation line on the wall, and snap it on the four walls if possible. (3) Concrete mixing

Topic: Construction technical disclosure of subdivisional works Technical disclosure of concrete subdivisional works Technical disclosure of concrete items
Some masonry engineering construction Technical disclosure scheme
I Aerated concrete block 1) Technical preparation 1. Before block masonry, review the drawings of construction parts, get familiar with the drawings and master the design requirements and standards. 2. Prepare the masonry construction scheme according to the design requirements and quality standards. 3. Put forward the plan for the use of labor, materials and construction machines and tools according to the requirements of the construction scheme. 4. The performance, strength, density, drying shrinkage value, frost resistance and other tests of the inspection products shall be carried out according to the provisions of the current national standards. 5. Complete witness sampling and re inspection of mobilized materials and trial preparation of masonry mortar. 6. Organize construction personnel to carry out technical, quality and safety disclosure

Topic: Technical disclosure of brick masonry construction Masonry construction technical disclosure ppt Technical disclosure of aerated concrete masonry construction