match 10 numbers: 0-9 numbers, two letters, standard configuration.
model: SR-ZM series
Technical parameters:
Weight: 1.4Kg working pressure: 0.6-0.8Mpa
Steel letterhead: 12 font sizes: 4mm, 6mm, 8mm, 10mm 12mm (customized)
There are single font machine, turntable machine, double font machine (customized)
Features of pneumatic number smashing machine:
Widely used in automobile and parts production, high-pressure vessel manufacturer, aerospace, ship, railway, rail transit Large steel structure and other related enterprises. The main body is composed of cylinders with high impact force, and the head is installed with various specifications of steel font. Impact the steel die onto the part to be marked by high-speed impact. It is especially suitable for permanent identification in the fields of station number, serial number, product serial number, production date, etc. It is a good alternative to the traditional hand-held steel seal marking.
The pneumatic number smashing machine has low daily maintenance cost, except that the steel font needs to be replaced after a certain number of years. Other problems rarely occur.
According to needs, we can provide customers with parts marking test .
I instructions:
The air duct and connector of the pneumatic marking machine are connected with the compressed air, and the pressure reaches It can be used at 0.6-0.8Mpa. When operating, turn a word of the character code rotary table to the top, and then buckle the plate handle.
II Product features:
1. The whole machine is integrated and compact, requiring only air supply and more convenient operation
2. SR-ZM series pneumatic marking machine uses air compressor gas (it is recommended to use about 0.7Mpa compressed gas, and unclean gas will shorten the service life)
3. There are 10 numbers and 2 English letters in the code turntable. When you need to type a word, turn a word in the code turntable to the right and then hit it. Customers can select the 12 characters according to their needs
4. The steel letterhead is specially made of alloy steel, which is resistant to impact and abrasion
5. The Rockwell strength of the metal parts suitable for marking is about 58, the Brinell strength is about 560, and the number of times the steel letterhead is used is about 10000 times (depending on the hardness of the marking material).
6 , prefixed with T In order to better use safely and prevent the word from flying out and injuring the operator by mistake.
The letterhead manufacturing is a variety of processes, which ensures the durability of the letterhead and extends its service life. Normally, the number of hits per prefix is ten About 10000 times, depending on different materials.
It is easy to disassemble the letterhead. In order to facilitate the use of customers, a hexagonal socket is specially equipped. If customers need to replace the letterhead, they can quickly remove the screws on the turntable with the hexagonal socket.
Pay attention to maintenance when the machine with inferior size is used for a long time to prevent weak impact. The lubricating oil can be used ， Open the connection between the handle and the air pipe, and drop a few drops of lubricating oil from the air pipe inlet.
The configuration length of the gas pipe is 8m It can meet the working length range of customers. If it is not enough, the gas pipe can be directly connected to the outside. The connector of the gas pipe is a standard connector.
This product is suitable for marking numbers, letters and batch numbers of plates of any size
III matters needing attention
1、 Before use, be sure to read the manual of our pneumatic marking machine
2、 Only compressed air can be used, and the use pressure must not exceed 0.8Mpa
3、 Before commissioning, make sure that the pressure gauge of the air compressor is correct and reliable to avoid injury caused by overpressure
4、 When using the marking machine, pay attention to wearing goggles and protective gloves to ensure the safety of operators
5、 It is forbidden to use oxygen and other flammable gases, or use high-pressure gas compressor as the power source of pneumatic marking machine
6、 When replacing the steel head, be sure to remove the air connector first, and do not pull the trigger
7、 It is forbidden to point the turntable at yourself or others during work to avoid injury
8、 During operation, it is strictly prohibited to be close to flammable and explosive articles, and do not work in harsh environments that are prone to corrosion, rust and dust 。
9、 Please use the tools carefully and take good care of them. Do not knock, drop or empty the gun at will to avoid damage to the tools
10、 When the marking machine is not used for maintenance, the air source should be disconnected
11. If any injury or accident occurs due to operation not in accordance with this manual or in violation of routine operation, it has nothing to do with our products, and our company will not bear any responsibility.
Jinan Feipu Machinery Equipment Co., Ltd
www.cnfipol.com
