-
Detail design of general structural node of abutment of double arch bridge 3. The vertical projection of the arch axis (perpendicular to the arch springing line) in the driving direction is an arc 4. The arch line of pier and abutment is horizontal, and the height of side walls on both sides, please control the construction according to the elevation in the table 5. An expansion joint with a width of 2 to 3 cm is set above the arch foot of the abutment. The filler in the joint can be sawdust and asphalt, and the precast slab is made by 1:1 -
Design Drawing of 1-24m Span V-abutment Rigid Frame Arch Bridge The ordinary reinforced rigid frame arch bridge with 1-24m span V-abutment is adopted, with a total length of 42m and a width of 15m. The rise span ratio of this bridge is 1/7.3, which belongs to flat arch, and the horizontal thrust is relatively large. Therefore, V-shaped abutment is selected to reduce the impact of horizontal thrust on the bridge foundation. Simple shape, beautiful appearance and soft lines meet the requirements of the owner to create landscape architecture. VI -
Detail design of general structural nodes of lower abutment of tied arch bridge 1. Cast cast-in-place pile of abutment, cast in place cushion cap, box chamber abutment body, cap beam and install main bridge bearing after passing the inspection. 2. Support erection: the support shall be firm and meet the construction requirements through preloading (it is recommended to use temporary bored pile as the support foundation). 3. Hoist the prefabricated tie rod in place, and cast the tie rod joint, end and inner beam (from both ends -
Detail design of abutment node of municipal arch bridge lower works Pier cap: 1 cap: 2 10m arch: 3 22m arch: 4 6.314m arch: 5 deck slab: 6 management room: 7 10m approach slab: 8 middle cap: 9 deck railing: 10 walkway: 11 -
CAD sectional design drawing of abutment reinforcement of a reinforced concrete arch bridge Reinforcement of reinforced concrete arch bridge abutment, including: plan, elevation and design instructions in all directions, accurate and comprehensive design, detailed content, for reference, welcome designers to download~ -
Detail design of general structural node of abutment anti-collision wall of double arch bridge 3. The vertical projection of the arch axis (perpendicular to the arch springing line) in the driving direction is an arc 4. The arch line of pier and abutment is horizontal, and the height of side walls on both sides, please control the construction according to the elevation in the table 5. An expansion joint with a width of 2 to 3 cm is set above the arch foot of the abutment. The filler in the joint can be sawdust and asphalt, and the precast slab is made by 1:1 -
Detail design of general structural node of reinforced concrete slab arch abutment 1. Reinforced concrete slab arch, calculated span L=20.0m, bridge width B=10.0m; 2. Bridge type: the superstructure is reinforced concrete slab arch. The height of the main arch ring is 60cm, and the span loss ratio is 1:8. The main arch ring is arc line. The substructure is pile group foundation, bored pile, and the pile diameter is φ 100cm; 3. Design load: crowd: 4 -
Construction design drawing of Guangdong U-shaped abutment open spandrel stone arch bridge 01 Description 02 Quantity table of the whole bridge 1-30m Arch bridge calculation sheet 03KZA0+030.00 Layout plan of stone arch bridge 04KZA0+030.00 Layout plan of stone arch bridge type o05KZA0+030.00 General structural drawing of stone arch bridge abutment 06KZA0+030.00 Coordinate map of pile position of stone arch bridge abutment 0708KZA0+0 -
Design Drawing of Ordinary Rigid Frame Arch Bridge with 24m Lake crossing Landscape V-abutment Design drawing of ordinary rigid frame arch bridge with V-shaped abutment of 24m lake crossing landscape xx The central mileage of the bridge of No. 6 Road in the central area is 6K0+275.5. The main function of this bridge is to span the artificial lake, connect the traffic of No. 2 Bridge and No. 3 Road, and coordinate with the surrounding environment to form a landscape point. Therefore, the bridge type with beautiful shape should be adopted. Ordinary reinforcement of 1-24m span V-abutment is adopted -
Detail design of reinforced concrete slab arch bridge abutment pile reinforcement node 1. Reinforced concrete slab arch, calculated span L=20.0m, bridge width B=10.0m; 2. Bridge type: the superstructure is reinforced concrete slab arch. The height of the main arch ring is 60cm, and the span loss ratio is 1:8. The main arch ring is arc line. The substructure is pile group foundation, bored pile, and the pile diameter is φ 100cm; 3. Design load: crowd: 4 -
Detail Design of Reinforced Concrete Slab Arch Abutment Arch Pedestal Reinforcement Construction Node 1. Reinforced concrete slab arch, calculated span L=20.0m, bridge width B=10.0m; 2. Bridge type: the superstructure is reinforced concrete slab arch. The height of the main arch ring is 60cm, and the span loss ratio is 1:8. The main arch ring is arc line. The substructure is pile group foundation, bored pile, and the pile diameter is φ 100cm; 3. Design load: crowd: 4 -
Detail Design of Anti slip Structure Node of Reinforced Concrete Slab Arch Abutment 1. Reinforced concrete slab arch, calculated span L=20.0m, bridge width B=10.0m; 2. Bridge type: the superstructure is reinforced concrete slab arch. The height of the main arch ring is 60cm, and the span loss ratio is 1:8. The main arch ring is arc line. The substructure is pile group foundation, bored pile, and the pile diameter is φ 100cm; 3. Design load: crowd: 4 -
CAD complete detailed design reinforcement drawing of Dongpan abutment of a 50m steel framed arch bridge The reinforcement drawing of Dongpan abutment of 50m rigid frame arch bridge, the detailed drawing of CAD plan and elevation and the renderings are fully planned. The individual buildings are consistent with the general layout, and the corresponding relationship between them is accurate. There are no errors, omissions, and flaws in the drawings. Welcome to download. -
Construction Drawing of a 16m Reinforced Concrete Arch Bridge Abutment CAD Design Complete Structural Drawing Construction drawing of 16m reinforced concrete arch bridge Abutment structure drawing, including plan, elevation and design description in all directions. The design is accurate and comprehensive, with detailed contents for reference. All designers are welcome to download Ha~ -
Standard Drawing of a Stone Arch Bridge CAD Design Node Dimension Drawing of Independent Front Wall Abutment Standard drawing of stone arch bridge: dimension drawing of independent front wall abutment. The project data is in dwg format. The drawings include: detailed schematic diagram of each section, internal and external plans, plans of each floor, etc., design specifications, detailed content, welcome to download and view, thank you~ -
Detail design of reinforced concrete slab arch bridge abutment arch ring reinforcement construction node 1. Reinforced concrete slab arch, calculated span L=20.0m, bridge width B=10.0m; 2. Bridge type: the superstructure is reinforced concrete slab arch. The height of the main arch ring is 60cm, and the span loss ratio is 1:8. The main arch ring is arc line. The substructure is pile group foundation, bored pile, and the pile diameter is φ 100cm; 3. Design load: crowd: 4 -
Detail design of reinforced concrete slab arch bridge abutment reinforcement structure node 1. Reinforced concrete slab arch, calculated span L=20.0m, bridge width B=10.0m; 2. Bridge type: the superstructure is reinforced concrete slab arch. The height of the main arch ring is 60cm, and the span loss ratio is 1:8. The main arch ring is arc line. The substructure is pile group foundation, bored pile, and the pile diameter is φ 100cm; 3. Design load: crowd: 4 -
[Guangdong] Construction design drawings of U-shaped abutment open spandrel stone arch bridge (complete set) Location: Guangdong Compilation time: 2008 Serviceability: road bridge span size and multi span total length: 30m Carriageway location: load-bearing component stress of deck bridge: service life of arch bridge: permanent bridge material type: reinforced concrete bridge data catalogue 01 Description 02 Quantity table of the whole bridge 1-30m Arch bridge calculation sheet 03 KZA0 -
CAD Design Node Structural Drawing of Xiawang Bridge Abutment of a Half through Tied Arch Bridge Structural drawing of the abutment of Xiawang Bridge of a half through tied arch bridge. The project data is in dwg format. The drawings include: detailed schematic diagram of each section, internal and external plans, plans of each floor, etc., design specifications, detailed content, individual and general plans are consistent, and the corresponding relationship between each other is accurate. There is no mistake, omission, or defect in the drawings. Welcome to download and view, thank you~ -
CAD Design and Construction of Capping Beam Reinforcement of Steel Pipe Arch Bridge Abutment with Main Span of 130m for a River Bridge The steel bar structure of the steel pipe arch abutment of a river bridge with a main span of 130m. The project data is in dwg format, and the drawings include: detailed schematic diagram of each panel, internal and external plans, plans of each floor, etc., design specifications, detailed content, individual and general plans are consistent, and the corresponding relationship between each other is accurate. There are no errors, omissions, and flaws in the drawings. Welcome to download and view, thank you~ -
Complete Node Structural Drawing of CAD Design for Dongpan Abutment of a 50m Steel Arch Bridge The structural drawing of Dongpan abutment of the 50m rigid frame arch bridge, the detailed drawing and effect drawing of the complete planning CAD plan and elevation, the individual building is consistent with the general layout, and the corresponding relationship between each other is accurate. There is no mistake, omission, collision or defect in the drawing. Welcome to download. -
Construction Drawing of a 16m Reinforced Concrete Arch Bridge Abutment Pile Reinforcement CAD Design Structural Drawing Construction drawing of 16m reinforced concrete arch bridge Abutment pile reinforcement structure drawing, including: plan, elevation and design instructions in all directions, accurate and comprehensive design, detailed content, for reference, welcome designers to download Ha~ -
CAD Design Structural Drawing of Approach Slab at the Back of a Single span Deck type Open spandrel Arch Bridge Abutment with a Span of 49m The structural drawing of the rear approach slab of the 49m span single span deck type open spandrel arch bridge abutment, the detailed drawing of the CAD plan and elevation and the renderings are fully planned. The individual buildings are consistent with the general layout, and the corresponding relationship between each other is accurate. There are no errors, omissions, and flaws in the drawings. Welcome to download. -
CAD Design Drawing of 1-72m Half through Steel Pipe Arch Abutment Structure of Yudai Bridge on a River The 1-72m half through steel pipe arch abutment structure of a Yudai River Bridge includes: plan, elevation, etc. This drawing is of great reference value, and is hereby shared for everyone to learn. The content is detailed and can be downloaded for reference. -
CAD Design Structural Drawing of Abutment Cap Reinforcement of a Concrete filled Steel Tube Tied Arch Bridge of Gucheng Bridge Structural drawing of abutment cap reinforcement of concrete-filled steel tubular tied arch bridge of Gucheng Bridge, including plan, elevation, etc. This drawing is of great reference value, and is hereby shared for everyone to learn. The content is detailed and can be downloaded for reference. -
Structural Drawing of CAD Design Node for Abutment of a L0=36m Half through Catenary Reinforced Concrete Arch Bridge Structural drawing of L0=36m half through catenary reinforced concrete arch bridge abutment, including: detailed schematic diagram of each panel, internal and external plans, plans of each floor, etc., design specifications, detailed content, welcome to download and view, thank you~ -
[Zhejiang] Design and construction drawing of 42.8m thin steel tied arch bridge (ribbed abutment rock socketed pile) Design load: highway Class II. The bridge design line is located at the crown point (bridge centerline). Elevation of pier and abutment top elevation and base elevation refer to the elevation at the center of pier and abutment. Seismic intensity: 6 degrees. 6m approach slab is set at the bridge head. The upper part of the bridge adopts 42.8m tied arch composite beam with a rise span ratio of 1:5, the lower part adopts rib abutment, and the rock socketed pile foundation is connected to the cushion cap. Pile diameter: φ -
CAD Design and Construction of Reinforcement in Cushion Block of a Concrete filled Steel Tube Tied Arch Bridge of Gucheng Bridge The data of the project is in dwg format, and the drawings include: detailed schematic diagram of each section, internal and external plans, plans of each floor, etc., design specifications, detailed content, individual and general plans are consistent, and the corresponding relationship between each other is accurate. There are no errors, omissions, and flaws in the drawings. Welcome to download and view, thank you~ -
General CAD design construction drawing of abutment of a 80m span through concrete-filled steel tube simply supported tied arch bridge The 80m span through concrete-filled steel tube simply supported tied arch bridge abutment is general. The project data is in dwg format. The drawings include: detailed schematic diagram of each section, internal and external plans, plans of each floor, etc., design specifications, detailed content, individual and general plans are consistent, and the corresponding relationship between each other is accurate. There is no mistake, omission, or missing in the drawings. Welcome to download and check, thank you~ -
CAD design drawing of reinforcement drawing of abutment cushion cap of a L0=36m half through catenary reinforced concrete arch bridge L0=36m half through catenary reinforced concrete arch bridge abutment cushion cap reinforcement drawing, complete planning CAD plan and elevation detail drawing and renderings, individual and general plan are consistent, and the corresponding relationship between each other is accurate. There are no errors, omissions, collisions and defects in the drawing. Welcome to download. -
Complete Reinforcement Drawing of CAD Design for Abutment Cap of Xiawang Bridge of a Half through Tied Arch Bridge The abutment cap reinforcement drawing of Xiawang Bridge of a half through tied arch bridge of a bridge, including the plan, elevation, etc. This drawing is of great reference value, and is hereby shared for everyone to learn. The content is detailed and can be downloaded for reference. -
Construction Drawing of a Changjiang Road Bridge General CAD Design Structural Drawing of Full Set of Truss Arch Bridge Abutment Construction drawings of Changjiang Road Bridge A complete set of general structural drawings of truss arch bridge abutment, including plan, elevation, etc. This drawing is of great reference value, and is hereby shared for everyone to learn. The content is detailed and can be downloaded for reference. -
CAD detail node design of a reinforced concrete tied arch abutment with a clear span of 50m Reinforced concrete tied arch abutment with a clear span of 50m, including: plans, elevations and design instructions in all directions. The design is accurate and comprehensive, with detailed contents for reference. All designers are welcome to download Ha~ -
CAD complete plane design structural drawing of abutment approach slab reinforcement of a through tied arch bridge with a span of 90m Structural drawing of abutment approach slab reinforcement of through tied arch bridge with a span of 90m, complete planning of CAD plan and elevation details and renderings, individual buildings are consistent with the general layout, and the corresponding relationship between them is accurate. There are no errors, omissions, and flaws in the drawings. Welcome to download. -
Complete structure of abutment foundation reinforcement CAD design for concrete-filled steel tubular tied arch abutment of Gucheng Bridge Steel bar structure of abutment foundation of concrete-filled steel tube tied arch abutment of Gucheng Bridge, including plan, elevation, etc. This drawing is of great reference value, and is hereby shared for everyone to learn. The content is detailed and can be downloaded for reference. -
Complete Structural Drawing of CAD Design for Abutment Body Reinforcement of Steel Pipe Arch Bridge with Main Span of 130m of a River Bridge Structural drawing of abutment body reinforcement of steel pipe arch bridge with main span of 130m of a river super large bridge, including plan view, elevation view, etc. This drawing is of great reference value, and is hereby shared for everyone to learn. The content is detailed and can be downloaded for reference. -
CAD Design and Structural Drawing of Reinforcement for Pile Foundation of Steel Pipe Arch Abutment of a River Bridge with a Main Span of 130m The reinforcement structure of the steel pipe arch abutment pile foundation of a river bridge with a main span of 130m includes: plans, elevations and design instructions in all directions. The design is accurate and comprehensive, with detailed contents for reference. All designers are welcome to download Ha~ -
CAD Design Structural Drawing of Abutment of a 1-55m catenary Vierendeel Reinforced Concrete Arch Bridge of Aishan Bridge Structural drawing of abutment of 1-55m catenary vierendeel reinforced concrete arch bridge of Aishan Bridge, including: detailed schematic diagram of each section, internal and external plan, plan of each floor, etc., design specification, detailed content, welcome to download and view, thank you~ -
Detailed design and construction of reinforcement CAD detail drawing for abutment ear wall of concrete-filled steel tubular tied arch bridge of Gucheng Bridge Steel bar structure of abutment ear and back wall of concrete-filled steel tube tied arch bridge of Gucheng Bridge, including plan, elevation, etc. This drawing is of great reference value, and is hereby shared for everyone to learn. The content is detailed and can be downloaded for reference. -
CAD Design and Construction of Steel Bar for Pad Stone Block of Steel Pipe Arch Abutment with Main Span of 130m of a River Bridge The construction of steel tube arch abutment bearing pad stone and retaining block reinforcement of a river bridge with a main span of 130m. The project data is in dwg format, and the drawings include: detailed schematic diagram of each section, internal and external plans, plans of each floor, etc., design specifications, detailed content, welcome to download and view, thank you~
