-
Course Design Calculation Sheet of 21m Trapezoidal Steel Roof Truss Course design of trapezoidal steel roof truss, roof slope 1:16, span 21m, length 96m, (2) 1.5m × 6m prestressed concrete large roof panel, 80mm thick foam concrete protective layer, coiled material roof, roof slope i=1/16. The standard value of roof live load is 0.7kPa. 19 pages in total. -
Course Design Calculation Sheet of Plant Trapezoidal Steel Roof Truss This material is: design calculation sheet of workshop trapezoidal steel roof truss course, which is detailed and can be used by designers for reference! -
Course design calculation sheet of a 18m trapezoidal steel roof truss This material is a course design calculation book of a 18m trapezoidal steel roof truss, which is detailed and can be used by designers for reference! -
[Bachelor] Course design calculation sheet of a trapezoidal steel roof truss Dead weight of roof truss and support 0.45KN/m2; Roof waterproof layer 0.4KN/m2; Leveling layer 0.4KN/m2; Self weight of large roof slab (including joint grouting) 1.4KN/m2. -
Course design calculation sheet of a 36m span trapezoidal steel roof truss Since the permanent load on the roof is large, the design value of negative wind pressure is less than the standard value of permanent load, and the internal force of the member will not change under the combined action of permanent load and wind load, the impact of wind load is not considered. -
[Bachelor] Course design calculation sheet of a 18m trapezoidal steel roof truss According to the plant length (90m>60m), span and load conditions, three horizontal supports are set for the upper chord, and the lower chord is not set because the span of the lower chord is 18m. -
[Bachelor] Design calculation sheet of workshop trapezoidal steel roof truss course Structural form: reinforced concrete column, trapezoidal steel roof truss. The concrete strength grade of the column is C30, and the section is 300 × 300mm. The roof edge height is 234cm, and the roof slope i=1/10; The calculated temperature of the area is higher than - 200 ℃, there is no corrosive medium, the seismic fortification intensity is 7 degrees, and there are two 200/50 medium duty cranes in the plant -
Course design calculation sheet of a 36m span trapezoidal steel roof truss Since the permanent load on the roof is large, the design value of negative wind pressure is less than the standard value of permanent load, and the internal force of the member will not change under the combined action of permanent load and wind load, the impact of wind load is not considered. -
Course Design Calculation Sheet of 24m Span Trapezoidal Steel Roof Truss_ This material is: 24 meter span trapezoidal steel roof truss course design calculation sheet, which is detailed and can be used by designers for reference! -
Course Design Calculation Sheet of 21m Trapezoidal Steel Roof Truss (1) Title 61, roof slope 1:16, span 21m, length 96m, location: Shanghai, basic wind pressure: 0.20kN/m, basic snow pressure: 0.55kN/m. The workshop is equipped with two 200/50kN intermediate working cranes, with rail top elevation of 8.5m. (2) 1.5m × 6m large prestressed concrete -
[Bachelor] Course Design of Trapezoidal Steel Roof Truss (including calculations and drawings) 1. Structural form: reinforced concrete column, trapezoidal steel roof truss. The concrete strength grade of the column is C30, and the section is 300 × 300mm. Roof slope i=1/10; The edge height of trapezoidal roof truss is 233cm. The regional calculated temperature is higher than - 200 ℃, there is no corrosive medium, and the seismic fortification intensity is 7 degrees; Two 200/50KN -
Course Design Calculation Sheet of 28m Span Flat Slope Trapezoidal Steel Roof Truss This material is the course design calculation book of 28m span flat slope trapezoidal steel roof truss, which is detailed and can be used by designers for reference! -
Copy [Bachelor] Course Design Calculation Sheet of a Trapezoidal Steel Roof Truss_ 1. Workshop column grid layout: 90m long; Column spacing: 6m; Span 18m2, roof slope: 1:10 3, roof material: prestressed large roof panel 4, load 1) dead load: roof truss and support dead weight 0.45KN/m2; Roof waterproof layer 0.4KN/m2; Leveling layer 0.4KN/m2; Self weight of large roof panel (including -
[Bachelor] Course Design of a Welded Trapezoidal Steel Roof Truss (including calculations and drawings) [Bachelor] Course Design of a Welded Trapezoidal Steel Roof Truss (including calculations and drawings) A factory building in Guangdong has a total length of 90m. The span is 21m from the attached table according to different student numbers, and the longitudinal column spacing is 6m. -
[Bachelor] 24 meter span trapezoidal steel roof truss course design calculation sheet A workshop has a span of 24 meters, a length of 192 meters, and a column spacing of 6 meters. There are two 20/5T intermediate working cranes in the workshop. The calculated temperature is higher than - 20 ℃, and the seismic fortification intensity is 7 degrees. 3.0 × 6m prestressed reinforced concrete large roof panel, 8cm thick foam concrete insulation layer, coiled material roof, roof slope is i=1/10. The snow load is 0 -
[Bachelor] Course Design Calculation Sheet of 28m Span Flat Slope Trapezoidal Steel Roof Truss A workshop has a span of 28 meters, a length of 72 meters, and a column spacing of 6 meters. A 1.5m × 6m prestressed reinforced concrete large roof slab is used. The ash load is 1.6 KN/m2, and the concrete grade is c30. -
Course Design Calculation Sheet of Steel Roof Truss Single story single span closed industrial plant, 120m long, roof truss hinged on reinforced concrete columns; Roof truss span 24m; Column spacing: 6m; The roof is about 20m above the ground. Indoor normal environment, crane lifting capacity 20/5t, working system A5, no large vibration equipment. -
Course Design Book of a Trapezoidal Roof Truss A single span single-layer factory building has a span of L ＝ 24m, a length of 54m, and a column spacing of 6m. There is no crane or vibration equipment in the factory building. The roof truss is hinged on the concrete column. The roof adopts a 1.5 * 6.0m space lightweight large roof panel. Q235-BF steel and E43 welding rod are used for manual welding. Column grid layout is shown in Figure 2.1. Allowable length ratio of member: roof truss -
Course Design Calculation Sheet of 27m Steel Roof Truss in a Workshop The design of a workshop steel roof truss (no crane, no skylight, no vibration) has a certain reference function for the undergraduate course design of steel structure roof truss. The pity of this material is that it does not include the construction drawing, which is also a defect. You can use PKPM modeling to generate standard drawings first, and then modify according to the content of manual calculation. -
Course Design Calculation Sheet of a 24m Steel Roof Truss This material is: a 24 meter steel roof truss course design calculation book, detailed and accurate, for designers to use! -
Design calculation sheet of a trapezoidal steel roof truss According to the length (), span and load of the plant, three upper and lower chord horizontal supports are set. As the column grid adopts closed combination, the horizontal support at both ends of the plant is set between the first column, and the specification of the horizontal support is different from that of the support between the middle columns. Rigid and flexible tie bars are set on the top chord plane between all columns to ensure the stability of the top chord during installation -
Course Design Calculation Sheet of a Steel Roof Truss This material is: a steel roof truss course design calculation book, detailed and accurate, for designers to use! -
Design calculation sheet of trapezoidal steel roof truss The trapezoidal roof truss has a span of 27m, a roof truss spacing of 6m, and a plant length of 84m. The roof truss is supported on the reinforced concrete column, and the joints are connected by welding. The reinforced concrete column is 12m high, and its concrete strength grade is C30. The steel is Q235-B, and the welding rod is E43. There is an intermediate working bridge crane in the plant, with a lifting capacity Q ≤ 300kN. Evenly distributed on the roof -
Final Course Design Book of Trapezoidal Roof Truss Calculation span of roof truss: l0 ＝ 1-2 × 0.15m ＝ 23.7m mid span and end height: H0 ＝ 2m for end height, H ＝ 3.2m for middle height; The arch camber is f ＝ 10/500, taking 50mm, and the upper chord gradient after arch camber is 1/9.6. -
Calculation Sheet for Course Design of Welded Ordinary Steel Roof Truss This material is: design calculation sheet of welding ordinary steel roof truss course, with detailed contents, which can be used by designers for reference! -
Course Design of Trapezoidal Steel Roof Truss - Steel Structure The structural layout is reasonable, the load calculation is correct, the value of various technical indicators is reasonable, the internal force calculation is correct, and the design of members is reasonable, meeting the requirements of "standards" and "specifications". -
[Bachelor] Design calculation sheet of trapezoidal steel roof truss The hot processing workshop of a factory in Xi'an has a length of 72m and a column spacing of 6m. The local calculated temperature is - 20C. The roof adopts 1.5 × 6m large roof panel (purlin free system). The roof structure composition is shown in the figure. The roof slope is i=1/8, the span end height is H0=2.2m, and the span is L=27m. The standard value of local snow load is 0.5kN/m2, and the standard value of ash load is 0 -
[Bachelor] Design calculation sheet of a trapezoidal steel roof truss Mid span and end height: take the end height of the roof truss at 27m axis: h=1.975m, the middle height of the roof truss: h=3.100m, then the roof truss is at 26.700m, and the height of both ends is h=1988m. The arch camber in the middle of the roof truss span is considered as Lo/500, taking 60mm. -
[Bachelor] Course Design Book of a Trapezoidal Roof Truss A single span single-layer factory building has a span of L=24m, a length of 54m, and a column spacing of 6m. There is no crane or vibration equipment in the factory building. The roof truss is hinged on the concrete column, and the roof adopts a 1.5 × 6.0m space lightweight large roof panel. Q235-BF steel and E43 welding rod are used for manual welding. -
Course Design of 21 meter Trapezoidal Steel Roof Truss A metalworking workshop. The purlin free roof system and trapezoidal steel roof truss are adopted. The workshop span is 21m. A roof truss calculation sheet and a roof truss construction drawing are attached. -
Course Design Calculation Sheet of Steel Roof Truss of a University in Shenzhen (1) Catalog (2) Design data (3) Geometric dimensions of roof truss and purlin setting (4) Support layout and roof truss number (5) Internal force calculation of members (6) Determination of roof truss node plate thickness, selection of member section and filler plate setting (7) Node design (8) Description (9) Design summary -
[Bachelor] Design calculation sheet of a 24m steel roof truss course The prestressed large concrete roof slab in G410 (I) standard drawing is used as the roof slab, and the standard value of dead weight is 1.4 kN/m2; Two felts and three oils are made on the roof panel, and the standard value is 0.35KN/㎡. B The model of gutter is 92G410 (II) according to the load value of external uniform wiring. When calculating the ponding load of gutter. It shall be determined according to the maximum depth of gutter. -
Examples of Course Design of Trapezoidal Roof Truss Location: Chengdu, basic wind pressure: 0.10kN/m, basic snow pressure: 0.25 kN/m. The workshop is equipped with two 200/50kN intermediate working cranes, with rail top elevation of 8.5m. -
Course Design of Steel Structure - Calculation Sheet of 24m Steel Roof Truss This material is: Course Design of Steel Structure - Calculation Sheet of 24m Steel Roof Truss, which is detailed and can be used by designers for reference! -
[Bachelor] Course Design Calculation Sheet of Welding Ordinary Steel Roof Truss 1. A single storey and single span industrial plant, with a span of 24m and a length of 102m. 2. The column spacing of the plant is 6m, reinforced concrete column, concrete strength grade is C20, the section size of the upper column is 400 400, and the steel roof truss is supported on the top of the column. 3. One crane is 150T and one is 30T, and the elevation of crane platform is+12.000m. 4. Load standard value（ -
Design calculation sheet drawing of trapezoidal steel roof truss with span of 24m The span of a factory building is 24m, the total length is 90m, the column spacing is 6m, and the bottom chord elevation of the roof truss is 18m. The roof adopts 1.5 × 6m large prestressed reinforced concrete roof slab. (Roof slab is not considered as support) Trapezoidal steel roof truss is used to consider static load: ① prestressed reinforced concrete roof slab (including caulking), ② two felt and three oil, ③ leveling layer, ④ support weight is considered live -
Course Design of 24 meter Span Trapezoidal Steel Roof Truss This material is: [Bachelor] Course Design of 24 meter Span Trapezoidal Steel Roof Truss. The content is detailed and can be used by designers for reference! -
Course Design Assignment and Instruction of Trapezoidal Steel Roof Truss A workshop has a span of 27, 33, 36m, a total length of 90m, and a column spacing of 6m. Two 300/50kN intermediate working cranes (see the plan and profile) are installed in the workshop. The working temperature is higher than - 20 ℃, there is no corrosive medium, the seismic fortification intensity is 6 degrees, and the bottom chord elevation of the roof truss is 12.5m; 1.5 × 6m prestressed reinforced concrete -
Calculation sheet of 30m trapezoidal steel roof truss The trapezoidal steel roof truss has a span of 30m, a length of 72m, a minimum temperature of - 20 ℃ in winter, a seismic design intensity of 7 degrees, and a design basic seismic acceleration of 0.1g. 1.5m × 6m prestressed concrete large roof panel, 80mm thick foam concrete insulation layer, coiled material roof, roof slope i=1/10. The standard value of roof live load is 0.7 kN -
Two-way board course design calculation sheet I only send high-quality materials, the formula can be edited, and the pictures are editable cad drawings, which are written according to the latest specifications
-
one Stress of trapezoidal steel roof truss -
two Trapezoidal steel roof truss micro plate -
three Calculation sheet of trapezoidal steel roof truss -
four Cad of trapezoidal steel roof truss -
five 27m trapezoidal steel roof truss -
six Course Design of Trapezoidal Steel Roof Truss -
seven Course Design Calculation Sheet of Steel Roof Truss -
eight Design calculation sheet of trapezoidal steel roof truss