)The wiring of the automatic fire alarm system project shall comply with the provisions of the current national standard Code for Construction and Acceptance of 1KV and Below Electrical Installations Wiring Engineering GB50258-96.(2) The core section of the transmission line of the automatic fire alarm system shall not only meet the technical conditions, but also meet the mechanical strength requirements.Minimum copper core insulated conductor laid through pipes
1. System wiring: 2. Installation of fire detector 3. Installation of manual fire alarm button 4. Installation of fire alarm bell and door lamp 5. Installation of fire alarm controller 6. Fire emergency broadcasting 7. Special telephone for fire protection 8. Acceptance and intermediate acceptance of concealed works 9. Commissioning of automatic fire alarm system 10. System acceptance
This article is a code for fire protection design of high-rise buildings, which is described in detail from the classification of high-rise civil buildings, outdoor fire water supply pipeline settings, etc.
The Ministry of Housing and Urban Rural Development is responsible for the management and interpretation of the mandatory provisions of this Code, the Fire Department of the Ministry of Public Security is responsible for the daily management, and the Shenyang Fire Research Institute of the Ministry of Public Security is responsible for the interpretation of the specific technical content.
This paper briefly introduces the fire protection specifications for diesel generators, including the configuration of fire protection facilities, fire protection settings, etc
This specification is divided into 14 chapters and 7 appendixes, including: general rules, terminology, design water consumption of fire water supply system, fire water supply system, fire water source, water supply facilities, fire hydrant system, pipe network of fire water supply system, fire drainage, hydraulics
This document is GB 50072-2010 Code for Design of Cold Storage. It contains complete and detailed contents, which can be downloaded by designers for reference.
This document is GB 50157-2003 Code for Design of Metro, which contains complete and detailed contents and can be downloaded by designers for reference.
In this project, the seismic fortification target, seismic fortification category, site classification, response spectrum and seismic design method of the Chinese seismic code GB 50011-2010 and the Australian seismic code AS11704-2007 carried out a detailed comparative analysis, and pointed out the similarities and differences between the two codes, which is helpful to further understand China's seismic code GB
In view of the different expressions of fire protection design codes on fire water supply design, which leads to different requirements of the same project in different codes, this paper discusses the rationality of each code's guidance on fire water supply design in combination with actual projects
This code has made major revisions to the Code for Design of Concrete Gravity Dams and its annual supplementary provisions, referred to as the original code, in the following aspects: the structural design adopts the probabilistic limit state design principle, and the partial coefficient limit state design expression replaces the calculation principle and method of the fixed value method used in the original code. The rock mass classification of the dam foundation provides the rock mass and concrete contact surface. The rock mass of the dam foundation is deepjunction
According to the requirements of the Regulations on Post Wenchuan Earthquake Recovery and Reconstruction issued by the State Council and the No. 1 Revision of Earthquake Ground Motion Parameters of the disaster area revised by the Seismological Bureau, the fortification intensity of the disaster area has been changed accordingly, and it is proposed to add some amendments to the articles. A total of 28 to 29 articles have been changed. The contents are as follows: 1Change of fortification intensity in disaster area, involving Sichuan, Shaanxi and Gansu
The Code for Design of Chimneys is now approved as a national standard, numbered GB 50051-2002, and will be implemented as of May 1, 2003.Among them, 3.1.1, 3.1.3, 3.2.2, 4.1.6, 5.2.1, 5.6.1, 5.6.2, 6.6.10, 7.1.1, 1.2, 8.1.4
By comparing the difference between the "Code for Residential Buildings" and the relevant provisions of the current national technical standards for fire protection, this paper puts forward the viewpoint of residential fire protection design.
This specification mainly describes the technical requirements for the design, materials, construction, inspection, commissioning and acceptance of the ground radiant heating project. I hope it will be helpful to you.
The design specifications for ventilation and air conditioning outlets (generally divided into three sections) are available for reference and download.
The wet system shall be used in places where the ambient temperature is not lower than 4 ℃ and not higher than 70 ℃.Dry system shall be adopted for places with ambient temperature lower than 4 ℃ or higher than 70 ℃
The latest design specifications for general hospitals can be downloaded if you are interested.The latest design specifications for general hospitals can be downloaded if you are interested.
Various instrument design specification templates Various instrument design specification templates Various instrument design specification templates, including drawings;See the appendix for details
Standard specification for water supply and drainage: Energy saving design specification for electronic engineering, with detailed contents for reference.
Code for design of electric heat tracing for fire protection
The topic of fire electric heat tracing design code provides you with the sharing of documents related to fire electric heat tracing design code. You can download the documents related to fire electric heat tracing design code for learning and reference. For more contents related to fire electric heat tracing design code, please visit