-
Installation construction scheme of a 600000 ton steam turbine generator set in Jilin Jilin 600000 ton/year fuel ethanol self-contained power plant project has two double extraction condensing steam turbines, the model is B25-8.82/1.078, the rated inlet pressure is 8.82 MPa, and the rated inlet temperature is 535 ℃. The generator adopts brushless excitation generator, model is QF-25-2, rated power is 25MW, rated voltage is 10.5KV -
Construction Scheme of New Generator Unit Installation Project in a Power Plant According to the construction scheme for the installation of new generating units of a power plant, * * power plant is located on the opposite bank of Leishui River, about 3km south of * * City. It is a pithead power plant with the original design planning capacity of 1000MW. Two 200MW coal-fired generating units have been built in Phase I project, and dumper room, some coal conveying belt trestles and circulating water pump room have been expanded to meet the requirements of two 300MW -
Construction design scheme for installation of power failure prevention generator in large buildings Strict technical review system. After the route and elevation of the pipeline are measured and positioned, professional engineers and quality inspectors shall recheck them before installation. Concealed works shall be jointly inspected and signed by the Supervisor, the Owner and other relevant units before entering the next process -
Construction Scheme for Installation of 25MW Steam Turbine Generator Unit in a Thermal Power Station in Hunan This project is the installation project of 25MW steam turbine generator unit of thermal power station, and the absolute duration of this project is 65 days. Due to the tight construction period and high technical content, in order to ensure the quality and progress of the whole project, the construction must be carried out according to the drawings, installation instructions and other technical documents provided by the design institute and the manufacturer during the installation process. And strictly implement the Power Construction -
Shandong Dezhou 30WM generator set and its auxiliary electrical equipment installation construction scheme This project is the construction scheme (measures) for the installation of 30MW generator unit and auxiliary electrical equipment of the residual pressure utilization project of Shandong Hualu Hengsheng Co., Ltd., with detailed data for reference. -
Installation construction scheme of a 1 × 3MW condensing steam turbine generator in Jiangsu A 64000 t/a anode project of a limited company has one waste heat boiler (model QC57/1000-28-1.25), whose parameters are P=1.25 MPa, t=194 ℃, Q=28 t/h, production steam in summer is 3 t/h, and heating and production steam in winter is 6 t/h. Low temperature waste heat power generation of aluminum company is now considered -
Design and Construction Scheme of a Vanke Diesel Generator Set Installation Unified Technical Standard In this project, there are two sets of electric starting batteries, one for standby and one for use. They should be as close to the unit as possible, and the voltage should be 24V. The capacity of each set should be determined according to the continuous starting of the diesel engine for no less than 6 times. -
Construction scheme of diesel generator set installation project in a construction site in Nanjing The hoisting commander instructs the crane driver to slowly and steadily lift the equipment 10 cm away from the truck, check the force on the wire rope and the load on the crane and floor, and continue hoisting after the "safety officer" confirms the safety -
Construction Scheme for High and Low Voltage Power Distribution and Standby Generator Installation Works of the Plaza The construction period of the project is tight and the quality requirements are high. In order to ensure excellent project quality and make the construction technology reach the first-class level, the construction scheme, construction methods and technical measures proposed in the Construction Organization Design strive to be specific, practical and targeted. At the same time, actively and carefully promote and apply advanced new materials, new equipment, new technologies and new processes, and demand quality The construction period and -
Construction Scheme for Generator Set Installation Project of Wanli Tire Co., Ltd. (Shantou Hongjun Electromechanical) The generator set installation project of Wanli Tire Co., Ltd. is located in the factory of Wanli Tire Co., Ltd., No. 3, Wanli Road, Aotou Town, Conghua, Guangzhou, Guangdong Province, -
Construction scheme for installation of vertical shaft Francis turbine generator unit of Guizhou Power Station The hydropower station is located in the middle and lower reaches of Qingshui River in the upper reaches of the main stream of fertile water, and in Jinping County, Qiandongnan Miao and Tuan Autonomous Prefecture, Guizhou Province. It is 80km away from Jianhe County and 25km away from Jinping County. It is the second stage of 15 cascade hydropower stations with horizontal flow and the only leading hydropower station with multi-year regulation performance. The power station is | grade project -
Construction scheme of diesel generator set The construction scheme of diesel generator set includes that the current construction unit plans to set three new air-cooled diesel generator sets with a power of 2000KW in the project of Global Communication Building (new site), which can be used as standby power supply for fire fighting, in order to ensure the emergency power needs of the fire fighting system, emergency lighting and elevator system of the building even when the supply of municipal power is stopped -
Special construction scheme for temporary power generator The section WA16~WA34 of Caonan Highway is the intercepting pipeline of Line A, which is designed to be jacked by the method of unslotted mud water balance; The total length of the pipeline is about 981m, including three 7000 * 3500, four Φ 4500 receiving wells and twelve Φ 1000 horse riding wells. The working shaft and receiving shaft shall be constructed in the reverse way, and the external side shall be constructed around D800@55 -
Method statement for start-up and commissioning of generator set The second unit of the third phase expansion project of a second power plant is a QFS-135-2 unit produced by Shanghai Electric Machinery Works. The excitation mode is a separate excitation static semiconductor excitation system composed of a coaxial AC exciter and a permanent magnet sub exciter. The generator and transformer are connected to the system in the form of generator transformer unit. Through the generator transformer unit startup test, the primary equipment and relay of the main electrical system -
Foundation construction scheme of a wind turbine Formwork system: the foundation formwork adopts the set shaped steel formwork, the internal part is reinforced with split bolts, and the external part is protected with Ф 48 × 3.5 steel pipes and connected with the main bent as a whole. -
Construction Scheme of Generator Foundation Slab in Shenhua Power Plant The four columns in the middle of the base plate are connected by the plate wall, with the top elevation of the plate wall+0.000m and the bottom elevation of the base plate - 6.1m. -
Construction Scheme of Unit Generator Phase I Project The construction scale of a power plant is 4 × 600MW subcritical domestic coal-fired unit generator, and the first phase project is 2 × 600MW. Our company is responsible for the # 2 unit of Bid B. The engineering overview of electrical discipline is as follows: -
Construction scheme for the use of generators in a simple garden in a community It includes power supply mode, distribution line at construction site, distribution box and switch box at construction site, generator installation process flow, generator foundation, auxiliary agent transportation and hoisting in place, exhaust and subsequent cooling system installation, etc. The contents are detailed for reference. -
Construction Scheme for Generator Unit Commissioning of Guangzhou Mansion A building is equipped with an 800KW diesel generator, which can automatically start in an emergency within 15 seconds for electrical and mechanical interlocking with the mains power to prevent parallel operation. It can be used as emergency power supply for fire fighting and standby power supply for important loads at ordinary times. This scheme is specially formulated for the trial operation of this generator set. -
Construction Scheme for Bottom Plate of Steam Turbine Generator 3.1 Project overview 3.1.2 The main power house is arranged in three rows, including the turbine room, the boiler front platform and the boiler room. The span of shaft A~B in the steam turbine room is 25m, the span of shaft B~C in the deaerator room is 8m, and the total length of the main power house is 132.20m. 3.1.3 The foundation of steam turbine generator is a large full plate foundation located between shaft A and shaft B. Its size is: length of base plate -
Construction and commissioning scheme of generator set This data is the construction and commissioning scheme of the generator set. The content is complete and available for reference. It is worth downloading by the designer -
Installation construction method of 600kW wind turbine During the installation and construction of 600kW wind turbine, a specially designed installation frame is used to ensure the installation quality of the generator, and good economic benefits are obtained. This construction method relies on the upper section of the tower drum, uses prefabricated shaft holes and hydraulic cylinder fixed supports to install a special installation frame, and uses the ground lifting winch system and hydraulic luffing of the installation frame to lift in place -
Construction scheme of turbine generator foundation in a power plant 1. xxx The turbine generator foundation of No. 1 and 2 units in Phase I is 23.93m long in longitudinal direction and 9m long in transverse direction, and consists of three parts: turbine generator foundation plate, heater platform plate and turbine platform plate. The bottom elevation of foundation slab is － 4.9m, and the top elevation is ＋ 8.95m. The foundation is cast-in-place reinforced concrete. Concrete grade: cushion C10, foundation slab C20, -
Construction Scheme for Desulfurization Flue of a Power Plant Generator Unit in Zhejiang Zheneng * * Power Plant Project has four 600MW coal-fired generating units, each of which is equipped with a desulfurization device. The desulfurized flue gas is introduced into the original flue gas from the horizontal flue part 41 at the chimney inlet, and the net flue gas after desulfurization returns to the horizontal flue from part 42, and then enters the chimney. Each unit desulfurization device has one bypass baffle and one original flue baffle -
Construction Scheme of Turbine Generator Foundation in a Power Plant This project is part of the structure above ± 0.00m of the base of 2 # steam turbine generator. The design service life of the structure is 50 years, the seismic fortification intensity is 7 degrees, the seismic fortification intensity of the seismic measures is 8 degrees, and the seismic grade of the frame is II. The steam turbine generator foundation is designed according to the technical data provided by Beijing Beizhong Steam Turbine Generator Co., Ltd. and ALSTOM. The unit model is: steam turbine -
Construction Scheme for Auxiliary Works of Generator in a Power Plant This project is the steam turbine generator project of the biological power generation project, which is located between the A~B axis and the 4~6 axis of the main power house. The bottom elevation of the foundation raft is -3.5m, the thickness of the foundation slab reinforcement protection layer is 50mm, the superstructure: the column reinforcement protection layer is 35mm, the cushion concrete is C15, and the foundation, column and upper operating platform beam slab concrete are C30 -
Construction scheme for installation of photovoltaic power generation system equipment in a city In this project, the prepared foundation will be transported to the site. According to the final required elevation, combined with the panel and cabinet location plan, check that the distance between embedded parts should not be greater than the width of the switch cabinet, and then install the foundation channel steel. After the installation of the foundation channel steel in the same place and on the same plane, its horizontal, error and vertical error should not exceed 1mm/m, and the total length should not exceed 3mm; Position error and non parallelism -
Construction Scheme for Steel Inner Cylinder Installation of Power Plant Project The outer reinforced concrete cylinder of XX power plant chimney is 205m high, the bottom diameter is 21.5m, the outlet diameter is 11m, and the elevation of the flue center line is 17.5m; The steel inner cylinder is designed to be self standing, with a total height of 210m. It is a circular section with a diameter of 8m within the full height range. It is connected with the concrete ring foundation by bolts (36 sets in total). In the reinforced concrete outer cylinder and -
Installation scheme of 220KW diesel generator set A 220KW Cummins diesel generator set is installed in the generator room of a community as an emergency power supply in case of mains power failure. When the mains power is cut off, the diesel generator set will be automatically started and automatically switched to the diesel generator feed circuit through the dual power automatic switching device in the distribution cabinet to supply power to the important loads in the museum area. The following describes how to install and debug the generator set. This data is 5 in total -
Construction scheme of steam turbine generator foundation of a power plant in Liaoning **(hereinafter referred to as Qinghe Company or the Company) is located in * * District, Liaoning Province, about 9km away from Kaiyuan City, 3.5km away from Qinghe Reservoir, and close to Shenyang City, the load center. It is the site of a large thermal power plant selected by China in the 1950s under the guidance of experts from the former Soviet Union. The base plate of the turbine base of the main power house is designed by Northeast Electric Power Design Institute, and the center of the base plate of the turbine base is located in the turbine room -
Construction Scheme of Turbine Generator Foundation of a Power Plant in Shanxi L=600mm (300mm inserted into the concrete) dowel bar. Before the construction of the upper layer, the surface of 50mm concrete shall be chiseled off and cleaned. -
Construction Scheme of a 100MW Steam Turbine Generator Foundation in Shandong This project is the foundation project of # 4 steam turbine generator of Shandong * * Thermal Power Co., Ltd., located in an area with seismic fortification of 7 degrees, ± 0.000m is equivalent to an absolute elevation of 65.00m. The foundation must act on the gravelly soil layer with a bearing capacity of 280KN/m2, and the foundation bottom elevation is designed to be - 5.1m (according to the geological report, gravelly soil has been reached -
Survey and construction scheme for infrastructure of vertical axis wind turbine Among the wind turbines, there are more horizontal axis wind turbines and fewer vertical axis wind turbines in the market. This survey and construction scheme has certain reference value for wind turbine practitioners engaged in vertical axis wind turbines. -
Construction Scheme Design of Steam Turbine Generator Base Plate Project overview and main quantities, qualification, requirements and quantity of operators, main construction machinery, tools, tools, construction preparations, operation sequence, operation methods, process requirements and quality standards -
Construction scheme for tower crane foundation and installation Three tower cranes are selected for this project, which are respectively arranged at 0A ～ 0B/9 ～ 10 axis, E ～ (2/C)/01 ～ 1 axis and 14 outer/K ～ (2/H) axis (see Figure 1 Tower Crane Layout Plan for specific locations). Two tower cranes are under the foundation raft, one tower crane is outside the building, and the tower bodies of 1 # and 2 # tower cranes pass through the underground four floors to -
Selected construction scheme for water and electricity installation This is the necessary information for the personnel engaged in construction electromechanical engineering. It is very good, and it is very practical information for both project managers and constructors -
Special construction scheme for large glass installation Special construction scheme for large glass installation, project overview, general construction deployment, platform 2 steel pipe rack checking, safety and civilized construction measures -
Construction scheme for tower crane installation and removal Construction scheme for installation and removal of tower crane: the tower crane adopts C35 reinforced concrete foundation, and the foundation drawings are provided by the construction unit according to the requirements of the instructions. The installation of tower crane is allowed only when the concrete strength reaches 75% or more of the concrete strength before installation -
Rebar fabrication and installation method statement Reinforcement fabrication and installation construction scheme, project overview, construction preparation, operation process, quality standards, and problems to be noted -
Installation construction scheme of a water plant in a city Installation construction scheme of a water plant in a city Installation construction scheme of a water plant in a city Installation construction scheme of a water plant in a city Installation construction scheme of a water plant in a city
-
one Temporary generator construction scheme -
two Wind turbine foundation construction -
three Fire fighting scheme design of generator -
four Generator safety technical disclosure -
five Fire protection design of wind turbine -
six Construction Scheme for Generator Set Installation -
seven Generator Unit Installation Construction Contract -
eight Construction scheme of tunnel generator room