-
Technical disclosure of typical main structure engineering This data is the technical disclosure of typical main structure engineering; The contents include: technical disclosure of reinforcement electroslag pressure welding works, brick concrete structure reinforcement binding works, brick concrete structure formwork works, construction hole retention and treatment; The content is detailed and can be used for reference. -
Technical disclosure of main structure masonry works Hanging line must be carried out during masonry. For long wall, a fulcrum can be set in the middle. The small line must be tightened. Each layer of brick must be threaded and leveled -
Technical disclosure of main structure concrete works According to the requirements of the engineering design drawings, the strength grade of the structural concrete construction part was defined, and the technical disclosure was made to the mixing team according to the technical requirements of the design. The concrete strength of this project is C10, C15, C20, C25, and C30. -
Technical disclosure of main structure formwork engineering 1.1.1 The formwork has been processed and configured according to the drawing size, and the surface of the formwork is flat and clean, with complete accessories. 1.1.2 The release agent used in this project has been checked, and the quality of release agent has been checked as required to meet the requirements. -
Technical disclosure of main formwork works The oil stain, mud, loose rust and other construction waste shall be removed from the formwork surface in contact with the concrete. -
Technical disclosure of masonry structure engineering New XB05 autoclaved aerated concrete blocks with strength grade not less than A3.5 are used for masonry construction in XXX station. The 200 mm new XB05 autoclaved aerated concrete block wall is used for the internal partition wall and external wall of the cable interlayer. 300 ㎜ new XB05 autoclaved aerated concrete block wall is adopted for the external wall of four equipment rooms in the station, and the internal partition wall is adopted -
Technical disclosure record of main structure masonry engineering The type and mark shall be selected according to the masonry position and the environmental conditions. Generally, 325 ordinary Portland cement should be used. -
Technical disclosure of foundation and main structure reinforcement engineering The high-rise structure of the project adopts shear wall structure, the foundation is raft combined with pile foundation, and the safety level of the building structure is Level II -
Technical disclosure of the main structure formwork project of a square After the quality of concealed columns is checked by the quality inspector and is qualified, the next process can be started. Binding of shear wall reinforcement mesh: during the binding process, two trapezoidal clamps are placed vertically at both ends of the shear wall to control the horizontal spacing of horizontal reinforcement; After the floor slab reinforcement is bound and before concrete pouring, a horizontal trapezoidal caliper is placed at the root of the shear wall to control the spacing of vertical reinforcement -
Complete set of technical disclosure of construction engineering (II) I paid 5000 dragon coins from Zhulong Online, and now it is uploaded in two sets. This part includes a full set of technical disclosure of installation engineering construction. It's no excuse not to give good comments on this material. -
Technical Disclosure of Construction Engineering The technical disclosure of construction engineering includes four parts: foundation, roof, decoration and main body -
Model of technical disclosure of construction engineering A complete set of 706 page technical disclosure of construction engineering A complete set of 706 page technical disclosure of construction engineering -
Construction engineering technical disclosure materials 2.1 Materials and main machines and tools: 2.1.1 Cement: 425 # Portland cement, ordinary Portland cement, or slag Portland cement shall be used, and expired, damp and deteriorated cement is strictly prohibited. 2.1.2 Sand: medium sand should be used, and the silt content should not be more than 3%. 2.1.3 Stones: pebbles should be used, and the maximum particle size should not be greater than 40mm, containing mud -
Technical disclosure of main structure of building construction Operators who erect scaffolds must pass the special training and examination and hold the qualified special operation certificate. Those who suffer from high blood pressure, heart disease and other operations unsuitable for climbing are not allowed to engage in scaffold erection and dismantling. -
Technical disclosure of main foundation formwork engineering The formwork system of the project adopts bamboo plywood wood formwork, brick mold and some steel formwork, and the support system adopts steel pipe fixtures and bolts. -
Technical disclosure of main reinforcement works Disclosure summary: matters needing attention during the fabrication and installation of reinforcement and specification requirements. -
Technical disclosure of main body and supporting masonry works The first layer shall be placed for trial masonry. The counting poles shall be erected at the corner and junction of the brick wall, and the alignment line shall be drawn between the counting poles, and the bricks shall be laid one by one according to the alignment line. -
Technical disclosure of main brick masonry works Construction drawings, construction organization design and relevant construction quality acceptance specifications -
Contents of technical disclosure of steel structure engineering National standard Code for Acceptance of Construction Quality of Steel Structures GB50205-2001 National standard Code for Design of Steel Structures GB50017-2003 National standard Technical Code for Cold formed Thin wall Steel Structures GB50018-2002 National standard Quality Inspection of Steel Structures -
Construction engineering technical implementation disclosure 4、 Finished product protection 1. The grounding wire shall be protected from mechanical damage and chemical corrosion; 2. Materials for grounding and lightning protection shall be properly kept to prevent corrosion of galvanized materials; 3. The buried depth of grounding body shall not be less than 0.6m; 4. Lightning protection and grounding works shall be carried out in coordination with civil construction, and finished product protection shall be carried out in coordination with each other; 5. Grounding main line of power transformation and distribution room -
Technical disclosure record of main works Divided according to the construction layout plan: material stacking area, rod assembly area, stacking area, and members shall enter the site according to the lifting sequence. -
Technical disclosure of demolition project of a construction company The demolition of buildings should be carried out from top to bottom. It is forbidden to demolish several floors at the same time. When one part is removed, other parts should be prevented from collapsing. -
Technical disclosure of building masonry engineering The embedded reinforcement connecting the reinforced concrete wall, column and masonry of the frame shear wall structure and the anti-seismic column of the brick concrete structure or the embedded reinforcement connecting the main wall, column and balcony masonry and coping must be recorded by Party A or the supervision company for concealment acceptance on each floor, and concrete pouring can be allowed only after it is qualified. -
Technical disclosure of reinforcement works of main structure of a square Before blanking, the blanking length of steel bars with welded joints must be considered, and the welded joints set in the same component shall be staggered. In the section from the center of any welding joint to the length of 35 times of the diameter d of the reinforcement and no less than 500 mm, the same reinforcement shall not have two joints; The percentage of the sectional area of load-bearing reinforcement with joints in this section to the total sectional area is -
Technical disclosure of concrete works of main structure of a residential building Construction preparation. Before pouring concrete, first take stones, sand and cement from the site for concrete of various strength grades, and then go to the laboratory for mixing test. The trial mix strength of concrete shall be increased by several values than the designed standard value of concrete strength. -
Technical disclosure of Yajule foundation and main structure reinforcement engineering 1. Process flow: setting out → reinforcement binding of cushion cap → reinforcement binding of bottom plate → reinforcement binding of foundation beam → reinforcement binding of upper layer of bottom plate → joint reinforcement 2. setting out: before laying reinforcement, mark the axis, frame column, shear wall, foundation beam of exterior wall and foundation coupling beam edge line, and control line of reinforcement mesh by snapping line on waterproof protective layer. In which, red oil is used at the corners of frame columns and shear wall concealed columns -
Main structure project disclosure Main structure project disclosure Main structure project disclosure Main structure project disclosure Main structure project disclosure -
Technical Paper on Building Steel Structure Engineering Knowledge and expertise, basic training of field engineers, basic knowledge of steel structure theory, professional knowledge of steel structure, strong practical work ability to engage in steel structure manufacturing, installation, construction organization and management, and certain steel structure design ability, to adapt to the forefront of steel structure manufacturing, installation, construction management, advanced practical, composite engineering and technical personnel -
Technical disclosure of brick concrete structure formwork engineering This data is the technical disclosure of the brick concrete structure formwork engineering. The data is valuable, detailed and accurate, and can be used for reference. -
Technical disclosure of steel structure welding engineering This section is applicable to the welding of carbon structural steel and low-alloy high-strength structural steel with steel thickness greater than or equal to 3mm in the steel structure engineering of industrial and civil buildings and general structures such as truss or grid structure (shell) structure, multi-storey and high-rise beam column, frame structure, etc. -
Technical disclosure of typical building electrical engineering This data is the technical disclosure of typical building electrical engineering; The contents include: technical disclosure of in pipe wiring engineering, distribution box installation engineering, switch socket installation engineering, lamp installation engineering, etc; The content is detailed and can be used for reference. -
Technical disclosure of masonry works of main building The stone used for stone masonry shall be solid and free from weathering, peeling and cracks. -
Technical disclosure record of main reinforcement works The main part of building 8 # in this project has 31 floors above ± 0.000, reinforced concrete shear wall structure system, and the total height of the building is 93m. -
Technical disclosure for formwork construction of main structure works The shear wall and column formwork of the project are supported vertically by 50 × 100 square timber with a spacing of 200, and horizontally by steel pipe Φ 12 through wall screws with a spacing of no more than 500. -
Technical disclosure for installation and removal of main formwork This project is a shear wall structure. In order to improve the surface leveling quality and construction speed of cast-in-place components, after entering the superstructure construction -
Safety technical disclosure of the main structure project of dilapidated house demolition Before erection, the fasteners shall be thoroughly inspected to check whether there are cracks, deformation, sliding wires, etc. -
Data of technical disclosure of construction engineering This data is a complete set of construction engineering technical disclosure data; The contents include: safety technical disclosure of glass installation, technical disclosure of reinforcement engineering, technical disclosure of aluminum alloy installation, etc; The content is detailed and can be used for reference. -
Technical disclosure of a complete set of typical construction projects I checked this website and found that the detailed construction technical disclosure data of the whole set of construction engineering technology is very few. The former colleague collected and copied to me a set of construction engineering technical disclosure data, which is very comprehensive, including foundation and foundation engineering, main structure engineering, building decoration engineering, waterproof engineering, building electrical engineering, water supply and drainage, Many professional aspects of HVAC engineering -
Technical disclosure of building water supply, drainage and heating engineering Process flow (1) Concealed laying of lightning protection downlead: straighten flat steel or round steel → transport → weld the lower end with the grounding body → lead up with the building → concealed inspection (2) Open laying of lightning protection downlead: straighten flat steel or round steel → transport → weld connection from top to bottom → connect the breaking clip with the grounding body (3) Laying of grounding main line in the power transformation and distribution room: reserved holes, embedded support parts → fixed support -
Technical disclosure of frame structure engineering According to the elevation, check whether the concrete surface elevation (column top, wall top) at the place where the lower layer extends out of the overlapping bar meets the requirements of the drawing, and chisel the exposed stones at the concrete construction joints and clean them. Scaffold shall be erected as required.
-
one Technical disclosure of architectural decoration engineering -
two Technical disclosure of building jacking engineering -
three Technical disclosure of main structure construction -
four Technical disclosure of building masonry engineering -
five Examination for technical disclosure of construction engineering -
six Construction engineering technical disclosure Baidu -
seven Technical disclosure of concrete structure engineering -
eight Technical disclosure of concrete main structure