Technical disclosure of civil air defense

Technical requirements disclosure of civil air defense supervision

This data is the disclosure of technical requirements of civil air defense supervision, in word format, 4 pages in total. Catalog: I. Introduction to civil air defense works (hereinafter referred to as civil air defense works) II. Precontrol of raw materials, components and equipment III, Precontrol of orifice protection works IV, Precontrol of civil air defense ventilation and air conditioning works V. Precontrol of building structure

Technical disclosure of building decoration

Face tiles: after the acceptance on site, they shall be selected before construction. Those with quality defects shall be removed first, and then the face tiles shall be selected according to the three categories of large, medium and small, and then stacked on the skids respectively. Different color numbers shall not be mixed.

Technical disclosure of building electrical installation

1 The main materials, semi-finished products, finished products, accessories, appliances and equipment used in the building electrical system must have quality certificates, specifications, models and performance test reports. 2. Materials shall comply with national technical standards or design requirements. Materials entering the site shall be inspected and accepted and reported to the supervising engineer for verification and confirmation. 3 The construction must meet the design requirements and construction specifications.

Architectural technical disclosure -- wall painting

1) The structural works have passed the acceptance. (2) Prepare double row external shelves, or hanging baskets and bridge shelves according to construction requirements. The stand pole of the shelf shall be 20cm away from the wall to ensure operation. It is better not to leave a scaffold eye on the wall to prevent secondary repair, which may cause a flowery feeling on the wall. (3) The reserved holes and buried pipes on the exterior wall have been treated. The cavity of the exterior wall is waterproof and no seepage is found after the water spraying test

Technical disclosure of civil air defense formwork engineering

Erection of full support → installation of plate formwork wooden edge → adjustment of floor slab lower surface elevation and arch camber → laying of formwork → inspection of formwork upper surface elevation and flatness → acceptance of plate formwork

Courseware for technical disclosure of civil air defense engineering

The project is located on the second floor of the basement of the civil air defense of the new community project of Phase II demolition and resettlement in Zengcheng Economic and Technological Development Zone, Guangzhou. The project is a Class A air defense basement with a civil air defense building area of 13420 square meters, which can shelter 3450 people. In peacetime, it is a car parking garage and equipment room; in wartime, it is a second-class personnel shelter, a shelter for members of the air defense professional team, and an air defense professional team outfit

Safety technical disclosure regulations of a construction company

For different construction methods, such as grade separation operation, slip form, scaffold construction, formwork construction, etc., which may bring unsafe factors to the construction, technical measures shall be taken to ensure safe construction

Safety technical disclosure of a construction company

The stacking of materials on the formwork shall be coordinated with the construction equipment, and shall be stacked in a decentralized manner, so as not to cause too much concentrated load. When there are special requirements for the load on the formwork, the construction and inspection shall be carried out according to the construction scheme and design requirements.

Safety technical disclosure form of a construction company

Project name, disclosure date, project position and disclosure content

Safety technical disclosure form 2 of a construction company

Construction unit, construction unit, project name, project location, area, safety director, foreman, team leader

Safety technical disclosure of complete installation and construction

Full set of safety technical disclosure for installation and construction, very comprehensive, more than 500 sets

Compilation of safety technical disclosure of a construction project

This article includes the safety disclosure of the following aspects: earthwork, reinforcement works, formwork works, formwork removal works, scaffold works, material requirements, fastener type steel pipe scaffold, tool type scaffold, basket type scaffold, ramp safety requirements, safety net masonry works, plastering and finishing works

Construction technical disclosure -- installation of wall cabinet and wall hanging cabinet

The technical disclosure in the construction enterprise is a technical disclosure made by the technical leader in charge to the construction personnel before the commencement of a unit project or a subdivisional project. Its purpose is to enable the construction personnel to have a more detailed understanding of the project characteristics, technical quality requirements, construction methods and measures, so as to organize the construction scientifically, Avoid technical quality, etc

Arrangement of construction technical disclosure forms

1. Operate in strict accordance with the manufacturing procedures; Welders, lifting workers and other special operators shall work with certificates. 2. The hazard sources on the construction site shall have obvious signs; When entering the construction site, you should dress neatly and wear safety helmet. 3. All kinds of lifting appliances need to be checked regularly and problems found should be handled immediately. 4. If the section length of the steel column is too large, the lifting point position and binding shall be selected for assembly and lifting

Architectural technical disclosure -- ceramic mosaic tile floor

Small bucket, half bucket, broom, square ruler, flat shovel, iron trowel, big bar, middle bar, small bar, screen, narrow trolley, steel wire brush, watering can, hammer, hardwood clapper (240mm × 120mm × 50mm), alloy pointed chisel, alloy flat chisel (welded K6 ～ K8 alloy steel sheets with Φ 6 reinforcement), steel sheet cutting, pulling plate (200mm × 70mm × 50mm)

General safety technical disclosure of building.xls

Technical disclosure of building energy conservation construction

Technical disclosure of building energy conservation construction

Technical Disclosure of Construction Engineering

The technical disclosure of construction engineering includes four parts: foundation, roof, decoration and main body

Summary of construction safety technical disclosure

Compilation of very comprehensive safety production management standard technical disclosure documents

Technical disclosure of building structure construction

Technical disclosure of building structure construction, including water and electricity, civil decoration, etc., from foundation to main body, from structure to decoration

Technical disclosure of construction safety

Personnel entering the construction site must correctly wear a qualified safety helmet, fasten the chin belt and lock the buckle; 2. During operation, personal protective equipment must be used correctly according to regulations, and the clothes must be neat. Barefoot, slippers and high-heeled shoes are strictly prohibited to enter the construction site; 3. When constructing at heights (2m or more) and steep slopes without reliable safety protection facilities, they must be tied up properly

Technical disclosure of main structure of building construction

Operators who erect scaffolds must pass the special training and examination and hold the qualified special operation certificate. Those who suffer from high blood pressure, heart disease and other operations unsuitable for climbing are not allowed to engage in scaffold erection and dismantling.  

Technical disclosure of construction safety (complete)

1. Personnel entering the construction site must correctly wear a qualified safety helmet, fasten the chin belt and lock the buckle;

Construction technical disclosure template

Every step

Complete set of technical disclosure of construction engineering (II)

I paid 5000 dragon coins from Zhulong Online, and now it is uploaded in two sets. This part includes a full set of technical disclosure of installation engineering construction. It's no excuse not to give good comments on this material.

Safety technical disclosure of construction equipment and machinery

This document is the technical disclosure for the safety of construction equipment machinery. The document includes: mortar mixer, plunger diaphragm mortar machine, extrusion mortar pump, shotcrete machine, high-pressure airless spraying machine, concrete mixer, concrete mixing plant, concrete mixing truck, concrete pump, concrete pump truck, concrete sprayer, plug-in vibrator, concrete vacuum suction pump Attached flat type

Technical disclosure of water conservancy construction quota preparation (formal)

Select professional manufacturers to order hollow grouting anchor bolts in strict accordance with the design requirements, and carry out relevant tests to ensure that the tensile pull force of the anchor bolt body meets the design requirements. The grouting slurry shall be cement slurry. In the construction preparation stage, relevant cement tests and water quality tests shall be completed, and the slurry mix design and relevant tests shall be carried out.

Construction engineering safety technology implementation disclosure

Concealed laying of lightning protection downlead: ① straighten the required flat steel (or round steel) with a hammer first. ② The straightened down lead shall be transported to the installation site, and shall be led up and hung up with the building according to the design requirements. ③ Timely weld the lower end of the down lead with the grounding body or connect it with the disconnection clip. With the gradual increase of the building, lay the down lead inside the building to the roof and out of the roof

Construction engineering safety technical disclosure system

Laying of grounding main line in transformer and distribution room: ① Determine the coordinate axis position according to the design requirements; ② After the support parts are buried, the grounding main line can be laid; ③ Brush yellow and green paint marks on the external surface of the grounding main line.

Construction engineering technical implementation disclosure

4、 Finished product protection 1. The grounding wire shall be protected from mechanical damage and chemical corrosion; 2. Materials for grounding and lightning protection shall be properly kept to prevent corrosion of galvanized materials; 3. The buried depth of grounding body shall not be less than 0.6m; 4. Lightning protection and grounding works shall be carried out in coordination with civil construction, and finished product protection shall be carried out in coordination with each other; 5. Grounding main line of power transformation and distribution room

Technical disclosure records for construction engineering

Formwork quality requirements: the erection of formwork must accurately grasp the geometric dimensions of components to ensure the accuracy of axis position. The formwork shall have sufficient strength, rigidity and stability, and can reliably bear the weight, lateral pressure and construction load of newly poured concrete. Before pouring, check whether the bearing frame and reinforcement support fasteners are tightened.

Technical disclosure of setting out in building construction

Before removing the support and formwork, the formwork can be removed only after obtaining the approval of the relevant parties. The formwork removal permit system is implemented. The formwork can only be removed when it meets the requirements of construction specifications without causing damage to the concrete surface.

Construction engineering technical disclosure materials

2.1 Materials and main machines and tools: 2.1.1 Cement: 425 # Portland cement, ordinary Portland cement, or slag Portland cement shall be used, and expired, damp and deteriorated cement is strictly prohibited. 2.1.2 Sand: medium sand should be used, and the silt content should not be more than 3%. 2.1.3 Stones: pebbles should be used, and the maximum particle size should not be greater than 40mm, containing mud

Model of technical disclosure of construction engineering

A complete set of 706 page technical disclosure of construction engineering A complete set of 706 page technical disclosure of construction engineering

Technical disclosure of roof waterproofing in building construction

The technical disclosure of roof waterproofing can be downloaded. After downloading, it can be used after modification. Come on, click Open. Now, download

Safety technical disclosure of demolition works

This document is the safety technical disclosure of the demolition of buildings. The contents are complete and can be downloaded

Registration Form for Safety Technical Disclosure of a Construction Company

Serial number, disclosure time, disclosure person, name, disclosure catalogue of parts and sub items, disclosure acceptor, number of pages, copies and registrant

Technical disclosure of demolition project of a construction company

The demolition of buildings should be carried out from top to bottom. It is forbidden to demolish several floors at the same time. When one part is removed, other parts should be prevented from collapsing.

Technical disclosure of steel framework of a construction company

Materials used for high-altitude operation shall be stacked stably, tools shall be put into the tool bag (sleeve), and objects shall not be thrown when passing up and down.

Technical disclosure of building masonry engineering

The embedded reinforcement connecting the reinforced concrete wall, column and masonry of the frame shear wall structure and the anti-seismic column of the brick concrete structure or the embedded reinforcement connecting the main wall, column and balcony masonry and coping must be recorded by Party A or the supervision company for concealment acceptance on each floor, and concrete pouring can be allowed only after it is qualified.