Technical disclosure of outer wall waterproof coiled material

External wall waterproof coiled material waterproof technical disclosure - 024

External wall waterproof coiled material technical disclosure - 024 External wall waterproof coiled material technical disclosure - 024 External wall waterproof coiled material technical disclosure - 024 External wall waterproof coiled material technical disclosure - 024 External wall waterproof coiled material technical disclosure - 024 External wall waterproof coiled material technical disclosure - 024 External wall waterproof coiled material technical disclosure - 024

Technical disclosure record of waterproof construction of basement outer wall coiled material

After the construction of the basement structure is completed and accepted, the waterproof construction of the basement exterior wall will begin. The bubbles on the exterior wall shall be leveled with cement putty, and the mortar, protrusions and screw heads adhered to the wall shall be removed with a small shovel or plastered with cement mortar to form a gentle slope of 1:6. The internal and external corners of the external wall shall be made into a circular arc with a radius of 50mm. Make the exterior wall meet the requirements of waterproof base specified in the specification (base

Technical disclosure of waterproof construction of SBS modified asphalt coiled material for basement exterior wall (hot-melt method)

Base course treatment: After the basement structure construction is completed and accepted, the waterproof construction of the basement exterior wall will begin. The bubbles on the exterior wall shall be leveled with cement putty, and the mortar, protrusions and screw heads adhered to the wall shall be removed with a small shovel or plastered with cement mortar to form a gentle slope of 1:6. The internal and external corners of the external wall shall be made into a circular arc with a radius of 50mm. Make the exterior wall meet the waterproof base specified in the specification

Technical disclosure of wet paving waterproof coiled material

1. Clean the dust and sundries on the surface of the base course for laying the waterproof layer, and remove the residual mortar hard blocks and protruding parts on the surface 2. The waterproof layer shall not be paved in rainy and windy days. 3. The coiled material and base treatment agent used for the waterproof layer shall be stored separately, away from the fire source, ventilated and adequately lit during operation.

Technical disclosure of PVC waterproof roll roofing

The variety, quality and technical performance of PVC waterproof roll must meet the requirements of design and construction technical specifications.

Safety technical disclosure record of waterproof coiled material

Contents of safety technical disclosure: 1. Safety helmets must be properly worn when entering the construction site, slippers, high-heeled shoes or hard soled shoes are not allowed to enter the construction site, and smoking is strictly prohibited on the site. 2. Safety protection articles must be properly worn during site construction, and safety belts must be properly fastened when working at heights. 3. Laughing, fighting and drunken operation are not allowed during site construction.

Technical disclosure of self-adhesive waterproof coiled material.doc

Technical disclosure of self-adhesive waterproofing membrane. doc Technical disclosure of self-adhesive waterproofing membrane. doc Technical disclosure of self-adhesive waterproofing membrane. doc

Technical disclosure of waterproof structure of exterior wall panel

This information is the technical disclosure of waterproof structure of exterior wall panel, which is valuable and detailed for reference.

Basement coiled material waterproof technical disclosure record

This disclosure is explained from the following aspects: process flow, practice of waterproof additional layer, waterproof lap width, upper and lower layer joints, and detail treatment.

Waterproof technical disclosure of exterior wall panel structure

1) Measures must be taken to protect the exterior wall panels during the process of leaving the pool, transportation, storage and hoisting, especially the size and shape of the waterproof structure must be kept intact without damage. If there are local damages, blocked cavities, honeycombs, pockmarks and other defects found before the installation of the exterior wall panels, they must be carefully repaired and hoisted and installed after reaching the strength. 2) The trough and cavity of the exterior wall panel are installed

Technical disclosure of stone like paint for an external wall

External wall external insulation base course acceptance qualified Apply external wall flexible water resistant putty External wall flexible water resistant putty acceptance Apply sealing primer Divided setting out Brush separation joint Coating on the separation joint Tape spraying stone like paint Tear off tape stone like paint Acceptance stone like paint polishing and spraying finish paint

Safety technical disclosure of SBS coiled material waterproofing for a residential project

1、 Construction equipment and accessories 1. Tools for cleaning waterproof base: shovel, broom, dust blower, hammer, steel chisel, etc. 2. Construction machines and tools for coiled material paving: scissors, tape measure, snapping box, scraper, brush, pressing roller. 3. Special hot-melt machines and tools: single head and multi head hot-melt spray guns. 4. Auxiliary materials: base treatment agent, coiled material adhesive, closing bead.

Technical disclosure of roofing coiled material waterproof layer

The position of the drain outlet and the distance out of the wall shall not affect the installation of the rain funnel, and shall not be close to the ventilation holes and air conditioning holes on each floor.

Construction technical disclosure of SBS waterproof coiled material for a roof

Construction technology disclosure of roof SBS waterproof coiled material, detailed design, for designers' reference.

Technical disclosure of roof SBS waterproof coiled material construction

Before paving coiled materials, remove the protrusions, mortar, lumps and other sundries on the surface of the base course, and clean the dust. The base course is dry, and the moisture content is not more than 9%. Detection method: lay 1m * 1m square of homogeneous coiled material on the waterproof base course, and open it 3 hours after the noon sun shines directly. If no watermark is found on the base course covering part and coiled material, the waterproof layer can be constructed.

Technical disclosure of roof SBS waterproof coiled material construction

When entering the construction site, safety protection equipment shall be properly worn. No smoking or drunk operation is allowed on the construction site. When taking blocks from the brick stack, take the high part first and then the low part to prevent the stack from falling and hitting people.

2019041714 Basement SBS coiled material waterproof technical disclosure

1. Construction preparation 1.1 Materials and requirements 1.1.1 Underground waterproof grade of the project is Grade II, and waterproof grade of equipment room is Grade I; Type II polyester based polymer modified asphalt waterproof coiled material. 1.1.2 Specification: 4+3mm thick, 1000mm wide and 10m long;

Waterproof technical disclosure of exterior wall panel.pdf

Technical disclosure of foundation waterproofing of a project

Poor lap of coiled material: the lap form of the joint and the lap width of the long and short sides are too small, the bonding at the joint is not dense, and the joint is damaged and empty; The standard line shall be snapped according to the procedure during the construction operation to make it conform to the specification of the coiled material. During the operation, the line shall be paved in line to make the long side of the coiled material not less than 100mm and the short side not less than 150mm.

Technical disclosure record of external wall thermal insulation

The technical disclosure record of external wall insulation is detailed and rich, which can be downloaded by netizens

Technical disclosure record of roof waterproofing

The quality requirements of the divisional and subdivisional works of the project must be excellent. The personnel entering the construction site must follow the unified command of the management personnel at the construction site. Before pasting the large area exterior wall tiles, the template must be made. After the design, supervision, construction and construction management personnel jointly check and approve, the large area pasting can be carried out.

Technical disclosure of external wall insulation pptx

The benzene plate insulation system has been used for decades abroad, and it has been 30 years since the beginning of the north in China. The technology has become mature. The external thermal insulation system of expanded polystyrene board thin plastering external wall has excellent thermal insulation performance, good waterproof performance, wind pressure resistance and impact resistance, which can effectively solve the problem of wall cracking and water leakage. But in 2009 and 2010

Technical disclosure of roof waterproofing

The installation elevation of the upper mouth of the water outlet cup shall consider the locally increased gradient (5%) at the water outlet and the thickness of the leveling layer, waterproof layer, additional layer and protective layer. The elevation must be accurate. After the leveling layer is plastered at the junction of the water outlet cup and the base course, a 20mm × 20mm groove shall be reserved and sealed.

Technical disclosure of exterior wall stone like paint project

Air compressor: the air compressor with power of more than 5kw, sufficient air volume and pressure of 0.5~1.0MPa is equipped with three gas pipes, which can meet the requirements of simultaneous construction of more than three people and can control the pressure automatically.

Anti corrosion and waterproof safety technical disclosure

General safety technical disclosure of anti-corrosion and waterproof construction, safety technical disclosure of steel pipe asphalt fiber cloth anti-corrosion construction

Technical disclosure of external wall plastering (already submitted)

1 Scope This process standard is applicable to indoor and outdoor plastering of cement mortar for industrial and civil buildings. 2 Construction preparation 2.1 Main materials and machines and tools: 2.1.1 Cement: 325 ordinary cement, with the same color, and the products of the same batch number should be used. 2.1.2 Sand: medium sand with an average particle size of 0.35~0.5mm, and the sand particles shall be hard and clean

Safety technical disclosure of external wall thermal insulation

1、 Safe operation and safety requirements: (1) The operators must be healthy, free from physiological defects, diseases not suitable for high-altitude operation, and competent for the work type. (2) When entering the construction site for operation, the safety production rules and regulations and labor discipline of the construction site must be strictly observed.

Technical disclosure record of polyurethane waterproofing

Before painting the waterproof layer, clean up the sundries and mortar blocks on the surface of the base course, and wipe them with a clean wet cloth. After inspection, the base course is free of unevenness, air cracks, sanding and other defects, the next process can be started.

Construction technical disclosure of basement BAC waterproof coiled material

The waterproof grade of the basement is Grade II. In addition to structural self waterproofing (waterproof concrete, impermeability grade P6), BAC double-sided self-adhesive waterproof coiled material shall be made on the upstream of the roof, bottom plate, outer wall, etc. The construction method of BAC coiled material shall refer to the atlas of SJ/T18-2006 (I), and the construction method of BAC coiled material protective layer shall be in accordance with SJ02-2003-2/60.

Safety technical disclosure of asphalt coiled material waterproof and thermal insulation project

Safety technical disclosure of asphalt coiled material waterproof and insulation project. doc, which is detailed and rich, can be downloaded by netizens.

Technical disclosure of asphalt felt roll roofing waterproof layer

This data is the technical disclosure of asphalt felt roll roofing waterproof layer, which is valuable, detailed and can be used for reference.

Technical disclosure of waterproof construction of foundation slab coiled material

Base course treatment → base course treatment agent painting → additional layer construction → acceptance → first layer SBS waterproof coiled material paving → coiled material end bonding, joint sealing → resisting coiled material isolation (protection) layer → acceptance → waterproof protective layer base course treatment: before paving coiled material, remove the protrusions, mortar, lumps and other sundries on the base course surface, and clean up the dust. Base course drying, test method: transfer 1m

Technical disclosure of waterproof construction of garage roof coiled material

Waterproof process flow: base course treatment → brushing cold primer → additional layer construction → laying the first layer of waterproof coiled material → laying the second layer of waterproof coiled material → hot-melt edge sealing → acceptance → water storage test → acceptance. The full adhesion method shall be adopted for the adhesion between coiled materials, and hollowing is not allowed. Lap width: the lap length of the long side of plane paving shall not be less than 100mm, and the lap length of the short side shall not be less than 100mm. Laying length of vertical wall

Technical disclosure of coiled material waterproof roof project of a commercial and residential building

Material 1. Cement: P.O42.5 or P O52.5 cement has no caking. When entering the site, quality certificate must be provided. 2. Sand: medium sand or coarse sand, fine sand can also be used after test, the mud content is not more than 5%, higher than C30 concrete, the mud content is not more than 3%. 3. Stone: pebble or crushed stone with particle size of 5-40mm and silt content of no more than 1%

Technical disclosure of waterproof coiled material for floor slab of residential building

This document is the technical disclosure of waterproof coiled material for residential building floor, in WORD format, 16 pages in total. The underground waterproofing membrane of this project adopts the construction process of external waterproofing and external sticking, that is, SBS Ⅱ PYPE4+3 waterproofing membrane is laid outside the underground structure (upstream). After waterproof construction, 120 thick autoclaved solid lime sand bricks shall be used outside to build waterproof protective walls.

Technical disclosure of roof coiled material waterproof construction - 052

Technical disclosure of roof coiled material waterproof construction - 052 Technical disclosure of roof coiled material waterproof construction - 052 Technical disclosure of roof coiled material waterproof construction - 052 Technical disclosure of roof coiled material waterproof construction - 052 Technical disclosure of roof coiled material waterproof construction - 052 Technical disclosure of roof coiled material waterproof construction - 052 Technical disclosure of roof coiled material waterproof construction - 052 Technical disclosure of roof coiled material waterproof construction - 052

Technical disclosure of waterproof construction of roofing coiled material.doc

Technical disclosure of SBS waterproof construction of basement exterior wall

Process flow: find out the joint part → clean the base course → paint the base course treatment agent → pave the additional layer, pipe root, grounding flat iron and other parts → hot melt paving coiled material → hot melt edge sealing → make the protective layer 1. Find the joint: find out and clean the waterproof coiled material joint reserved in advance under the raft before construction to check whether there is damage, and add an additional layer of the same width if there is damage. two

Safety technical disclosure record of asphalt coiled material waterproof and thermal insulation project

1. Scaffolds around the roof construction shall be 1.2 meters higher than the working face, the transportation road shall be smooth and smooth, and anti-skid measures shall be taken. 2. The asphalt boiling must be carried out in a covered place, in accordance with the fire prevention regulations, and must be equipped with sufficient and proper fire prevention equipment (such as fire extinguishers, river sand, wet sacks, iron pot covers, etc.). It is strictly prohibited to water to extinguish the fire. 3. Asphalt shall not

Technical disclosure record of asphalt felt roll roofing waterproof layer

(1) The quality and technical performance of coiled materials and other materials used must meet the requirements of design and construction acceptance specifications. The product has a certificate of conformity and should be retested. Coiled material: petroleum asphalt felt: no less than 350 low tire asphalt felt. Tar asphalt felt: low tire asphalt felt no less than 350. Asphalt glass fiber cloth felt. Asphalt linen linoleum.