Construction Process Manual of Urban Road Engineering

Construction Process Manual of Building Engineering

Before earth excavation, the obstacles such as underground pipelines shall be found out, and the above ground and underground obstacles in the construction area shall be removed and disposed according to the requirements of the construction plan. 2.2.2 The location of buildings or structures or the positioning control line (pile) of the site, the gray line size of standard horizontal pile and foundation trench must pass the inspection and go through the pre inspection procedures. 2.2.3

Complete Works of Highway Engineering Construction Technology

A complete set of highway engineering construction techniques, including roads, bridges and culverts, tunnels, etc., can be used for reference.

Demonstration manual for construction process of distribution network engineering - complete

Demonstration Manual for Construction Process of Distribution Network Engineering - complete, 123 pages in total, word. Editable for reference.

Code for construction and quality acceptance of urban road engineering

This document is the Code for Construction and Quality Acceptance of Urban Road Engineering, which is detailed and can be used for reference.

Construction technology of a highway project

This document is a complete set of construction techniques for a highway project. It contains a complete set of techniques. The contents are detailed for reference.

Complete List of Highway Engineering Construction.rar

Complete List of Highway Engineering Construction.rar

Block Diagram of Highway Engineering Construction Process

Block Diagram of Highway Engineering Construction Process

Graphic Manual for Construction Process of Building Engineering

Reinforcement lofting - reinforcement fabrication - formwork lofting - formwork fabrication - reinforcement binding and installation - formwork installation - overall acceptance - concrete pouring (sample of test block) - concrete curing - formwork removal - appearance detail treatment

Full set of detailed documents of 2K311000 urban road engineering construction

This document is a full set of detailed documents for the construction of 2K311000 urban road works, including professional formulas, calculation tables, mind maps and other forms. The document is standard compliant, reliable, rich in content, and detailed in ideas, which can be used for reference.

Safety operation specification for construction of urban road engineering

This data is the safety operation specification for urban road construction, which is detailed and can be used for reference.

Construction technology of lime soil base in a road project

Lime soil is the most commonly used material in municipal road engineering. On the basis of describing the construction preparation of lime soil base, this paper discusses the construction technology of lime soil base, and puts forward the construction precautions in special seasons.

6 - [State owned enterprises] Construction process manual of external wall insulation works

Construction technology of decoration works

Chapter I of the table of contents, section I of decoration works 3, floor decoration category 3, floor stone paving 3, composite floor floor 5, floor tile paving 6, floor carpet paving 10, stainless steel skirting installation 11, PVC floor construction scheme 12, floor carpet paving (block carpet) 13, floor plastic paving 14 Section II Wall works 16 Dali

Road engineering construction organization design

The construction organization design is the construction organization design of a plant road project for everyone to enjoy

Construction organization design of a road project

The project is divided into two lines: the east and west roads around the sludge plant. The west line is designed to start from Xiajiahezi Road and end at the intersection of the existing golf road, with a length of 897m; The design starting point of the east line starts from the west line road K0+264.209 and intersects the plant road, with a length of 106 meters.

Construction technology of ventilation and air conditioning works

This chapter details the specific requirements and specifications of ventilation and air conditioning engineering in construction

Construction process summary of decoration works

Including various practices in ground decoration engineering, wall decoration engineering and ceiling decoration engineering.

Masonry construction technology and nodes

Masonry engineering construction technology and node, this article is about materials and basic technology, construction node comprehensive details, etc

Construction technology of building masonry engineering

(1) Mortar is a kind of construction engineering material made of cement, fine aggregate, admixture and water in a certain proportion, which plays the role of bonding, cushion and stress transmission in construction engineering. (2) Masonry mortar bond bricks, stones and blocks into masonry mortar, mainly including cement mortar and cement mixed mortar. (3) Cement mortar consists of cement, fine aggregate and water

Construction process standard of pasting engineering

This data is the construction process standard of the papering project. It is valuable and detailed for reference.

Bidding Document for Road Engineering Construction

① Construction site: XX District; ② Construction scale: the project includes two road works, including Huatang Road (Xiangfu Road - Guixing Road), with a total length of 454.1 meters; Guixing Road (Xinhe Road Wanjiali Road), 479.06 meters in length and 20 meters in width, is a bid section with a project cost of about 25 million yuan; ③ Scope of bidding: XX road construction

Construction technology of caisson and caisson works

1. Fabrication method The fabrication method of open caisson is generally to be fabricated on the ground of the building structure, which is suitable for high groundwater level and allowable clearance. Artificial island construction is suitable for fabrication in shallow water. Fabrication in foundation pit is suitable for low groundwater level and not high clearance. It can reduce the sinking depth friction and the height of working face. It can be used according to different situations. Most of them are fabricated in foundation pit

Construction technology of concrete structure engineering

Construction process of concrete structure engineering Construction process of concrete structure engineering Construction process of concrete structure engineering See the appendix for details

Construction process disclosure of masonry works

The wall mortar joint is full, the mortar joint thickness is uniform, the wall surface is clean, the structural column is poured densely, the back plug height and the block slope are consistent, the door and window lintel is poured densely, the shelving length meets the specification requirements, and the appearance quality is good.

Construction document of road works in the community

The project is mainly caused by the fracture and collapse of the original buried sewage concrete pipeline outside the 3 # residential building in XX community, which often causes the drainage to be blocked and blocked; Now the UPVC-De300 pipeline is newly buried along the original pipeline. The pipeline adopts flexible rubber ring socket interface, and the pipeline length is 72m. The original septic tank collapsed and has been sealed, and the sewage is directly discharged into the main ditch, causing serious environmental pollution

Construction organization of a road project in Sichuan

Content introduction The project is classified as tourist road. According to the Minutes of Meeting on the review of the preliminary design scheme for the reconstruction project of * * * section issued by the Highway Management Office of * * City Communications Bureau, the principle is to use the old road as much as possible to meet the standard of Class II highway in mountainous areas. After economic and technical comparison, the standard of individual road sections can be appropriately reduced and safety facilities can be added. This design is 57 pages in total.

Construction process design of formwork works

One purpose two, quality control standard three, formwork construction process four, formwork removal five, full scaffold erection six, quality problem handling

Detailed Rules for Construction Supervision of a Road Project

(1) Before the building positioning survey, the construction project legal person shall provide the coordinates of the building corner marks measured and confirmed by the planning and surveying department. (including written notice and on-site coordinate handover) The corner marks are generally more than three points, two of which are used for positioning survey, and the rest are used for verification. (2) The construction unit shall properly protect the corner marker provided, when the corner marker is located in the building or during the construction process

Detailed construction process of dike works

Attention shall be paid to the following points in the selection of the protective embankment line (1) The protective embankment shall be selected on the embankment with single layer and solid soil, and the silty fine sand foundation and sludge zone easy to liquefy shall be avoided as far as possible to ensure the stability of the foundation. When the dam is likely to be scoured, the dam shall be stabilized

Construction process standard of painting works

Construction process standard of coating engineering Construction process standard of coating engineering Construction process standard of coating engineering

Construction process standard of masonry works

Brick wall is the most commonly used wall form for civil and industrial buildings. The utility model has the advantages of easy access to materials, simple construction, durability, low cost, etc; However, the wall is heavy and the masonry labor intensity is high. This process standard is applicable to wall works of civil building walls and frame structures, and enclosure walls of industrial plants.

Construction process standard of roof works

(1) The quality and technical performance of the materials used must meet the design requirements and construction quality acceptance specifications.

Analysis on the construction technology of papering project

038 Construction process of pasting engineering 038 Construction process of pasting engineering 038 Construction process of pasting engineering

Construction technology of bridge deck engineering

The reinforcement mesh of pavement layer is required to be flat and straight. The intersection of reinforcement shall be firmly bound with iron wire. The stressed reinforcement joints shall be staggered. The spacing between two joints shall not be less than 1.3 times the overlapping length. The sectional area of the stressed reinforcement configured in the overlapping length type section shall be less than 50% of the total sectional area of the reinforcement.

Construction process of overall curtain wall project

Note: gusset plate is one of the structural members connecting the curtain wall and the main structure. The quality of gusset plate fabrication and installation directly affects the connection function between the curtain wall and the main structure. The accuracy of installation also directly affects the accuracy of curtain wall construction and the quality of appearance. Therefore, as the first operation of curtain wall installation, the gusset plate has a direct impact on its fabrication and installation

Construction technology of cup foundation engineering

This article is a cup foundation engineering construction process, which is full of details and can be used for reference by netizens.

Construction technology of building decoration engineering

This document is about the construction process of architectural decoration engineering, with a total of 49 pages. The content is detailed and can be used for reference.

Handout on Road Engineering Construction PPT

The construction technology of road engineering is a simple and complex construction technology. This article tells the construction methods of subgrade, pavement base, pavement surface layer, special subgrade treatment and other projects in a simple and intuitive way through the form of slides,

Construction technology of foundation and foundation works

Comprehensive foundation and foundation engineering construction technology, including lime soil foundation engineering construction technology; Construction technology of sand and gravel foundation engineering Construction technology of reinforced concrete precast pile; Construction technology of slurry wall protection bored pile; Construction technology of spiral bored pile; Construction technology of manual hole forming pile; Construction technology of pile cap; Equipment foundation construction process; Construction technology of plain concrete foundation

038_Construction process of papering project

This process standard is applicable to the pasting works of interior walls, ceilings, etc. of industrial and civil buildings.