AP6010 series access point
Product appearance
appearance
port
1. Console port.
2. ETH/PoE: 10/100/1000M, used for wired Ethernet connection, and supporting PoE power supply. three
. Default: the default button. Press and hold for more than 3 seconds to restore the factory default value. four
Power input interface: 12V DC.
5. Lock device lock interface: used to ensure the anti-theft safety of the device.
LED indicator
| Information type | colour | frequency | Express meaning |
|---|
| Power on default state | green | Always bright | Just power on, the green light is always on. If you enter the uboot command line, the green light flashes with the command input. |
| function | green | Slow flashing (0.5Hz) | It indicates that the system is in normal operation, the system is in normal operation, the Ethernet connection is normal, and there is user association. |
| Slow flashing (0.2Hz) | The system operates normally, the Ethernet connection is normal, and there is no user association. |
| give an alarm | green | Flash (4Hz) | During the upgrade process, the CAPWAP chain is broken. |
| error | gules | Always bright | It indicates that the board has a fault that affects the service and cannot be recovered by itself, which requires manual intervention. |
Product characteristics
WLAN features
AP6010DN-AGN is compatible with IEEE 802.11a/b/g/n standard
AP6010SN-GN is compatible with IEEE 802.11b/g/n standard
AP6010SN-GN * High speed up to 300Mbps
AP6010DN-AGN * high-speed rate reaches 600Mbps
Support * Large Consolidation Ratio (MRC)
Support 11n beamforming
Supports cyclic delay/cyclic shift diversity (CDD/CSD)
Support * high likelihood decoding (MLD)
Support packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Rx only)
AP6010DN-AGN supports 802.11 Dynamic Frequency Selection (DFS)
It supports the mapping and priority scheduling rules of ShortGI based on WMM (Wi Fi multimedia), i.e. Wi Fi multimedia standard, in 20M and 40M modes, and implements priority based data processing and forwarding
It supports automatic and manual rate adjustment modes. The default mode is automatic rate adjustment mode
Support WLAN channel management and channel rate adjustment
Support the channel automatic scanning function to automatically avoid interference
Each SSID in the AP can be configured with hiding function independently, and Chinese SSID is supported
Support automatic hiding of SSID, that is, when the access terminal reaches the upper limit of access, the SSID will be automatically hidden
Support SST (signal sustain technology)
Support U-APSD power saving mode
CAPWAP (control and provisioning of wireless access points) tunnel data forwarding is supported under Fit AP working mode
Support AP automatic online function under Fit AP working mode
WDS support in Fit AP operating mode
Mesh support in Fit AP working mode
Support Mesh dual MPP networking
Support Hotspot2.0
Intelligent roaming supporting 802.11k and 802.11v protocols
Network characteristics
Comply with IEEE 802.3u standard
It supports self negotiation of rate and duplex mode, and automatic MDI/MDI-X supports the division of VLAN uplink Ethernet ports according to the SSIDs accessed by users
Support VLAN ID (1-4094), 16 VAPs can be set per RF
Support the networking of the AP interface management channel in tag and untag modes
Support DHCP client, obtain IP address through DHCP
Support tunnel forwarding and direct forwarding of business data
Support access isolation between different wireless terminals in the same VLAN
It supports the mDNS gateway protocol and can realize AirPlay, AirPrint and other service sharing functions between VLAN users
Support user access control (ACL)
Support LLDP link discovery
Support CAPWAP interruption service maintenance in direct forwarding mode under Fit AP working mode
Support AC unified authentication under Fit AP working mode
In Fit AP working mode, it supports AC dual link backup, VRRP hot backup supports Native IPv6, and IPv4/IPv6 dual protocol stack
IPv6 Portal support
Support IPv6 SAVI
Support IPv4/IPv6 ACL, etc
Support Soft GRE
QoS characteristics
Implement priority based data processing and forwarding based on the mapping and priority scheduling rules of WMM (Wi Fi multimedia), i.e. Wi Fi multimedia standard
Support WMM parameters management by RF
Support WMM power saving mode
Support uplink message priority mapping and downlink traffic mapping
Support queue mapping and scheduling
Support per user bandwidth limitation
Support adaptive bandwidth management, automatically adjust user bandwidth allocation according to user number, environment and other factors, and improve user experience
Safety features
Support Open System authentication
Support WEP authentication/encryption mode
Support WPA/WPA2 – PSK authentication/encryption mode
Support WPA/WPA2 – 802.1X authentication/encryption mode
Support WAPI authentication/encryption mode
Support WIDS and WIPS, including illegal device detection and countermeasures, attack detection and dynamic blacklist, and STA/AP blacklist function
Support DHCP Snooping
Support DAI (Dynamic ARP Inspection)
Support IPSG (IP Source Guard)
Support 802.11w protocol and encrypt management frame
Maintenance characteristics
Support centralized management and maintenance of AP through AC under Fit AP working mode
Under Fit AP working mode, it supports AP automatic online function, and automatically loads configuration, which can be plug and play
Support zero configuration deployment of WDS under Fit AP working mode
Mesh zero configuration deployment is supported in Fit AP working mode
Support batch automatic upgrade
The AP supports two local management modes: Telnet and serial port
Support NMS to monitor user configuration information in real time and locate faults quickly
Support AP system status alarm
Dying Gasp support
BYOD
Support identifying device type based on MAC OUI
Support identifying device type based on HTTP User Agent information
Support identifying device type based on DHCP Option information
Support the Raduis server to issue the forwarding/security/QoS policy of the message according to the device type carried in the Raduis authentication/billing message
Location service
Spectrum analysis
Identify more than 8 interference sources such as Bluetooth, microwave oven, cordless telephone, Zigbee, Game Controller, 2.4G/5G wireless audio and video, baby monitor, etc
Coordinate with eSight to locate and display the interference source
Product specification
Basic parameters
| project | describe |
|---|
| Physical parameters | Dimension (length × width × height) | 180mm×180mm×50mm |
| weight | 0.4 kg |
| system memory | 128 MB DDR2 32 MB Flash |
| Power parameters | Power input | DC 12V±10% POE power supply: - 48V DC Meet 802.3af/at Ethernet power supply standard |
| *High power consumption | AP6010DN-AGN：10.2W AP6010SN-GN：6.5W Note: The actual * large power consumption varies according to the regulations of different countries and regions. |
| Environmental parameters | working temperature | -10℃～+50℃ |
| Storage temperature | -40℃～+70℃ |
| Operating humidity | 5%~95% (non condensing) |
| Waterproof grade | IP31 |
| altitude | –60m～5000m |
RF parameters
| project | describe |
|---|
| Antenna type | Built in antenna |
| Antenna gain | AP6010DN-AGN： 2.4G：4dBi 5G：5dBi AP6010SN-GN：4dBi |
| Number of users who can be online at the same time | ≤128 |
| High transmit power per RF port | 20dBm The transmission power supports 1dB step size adjustment, and the adjustable range supports 20dB downward from * large transmission power. Note: The actual transmission power varies according to the regulations of different countries and regions. |
| AP6010DN-AGN non overlapping channels * large number | 2.4 GHz 802.11b/g 20MHz: 3 802.11n 20MHz: 3 40MHz: 1 | 5 GHz 802.11a 20MHz: 5 802.11n 20MHz: 5 40MHz: 2 |
Note: The number of non overlapping channels supported by different countries is also different. Please refer to the List of Country Codes&Channels for details. |
| AP6010SN-GN non overlapping channels * large number | 802.11b/g 20MHz: 3 802.11n 20MHz: 3 40MHz: 1 |
Note: The number of non overlapping channels supported by different countries is also different. Please refer to the List of Country Codes&Channels for details. |
| Supported Channel Rates | 802.11b: 1, 2, 5.5 and 11Mb/s |
| 802.11g: 6, 9, 12, 18, 24, 36, 48 and 54Mb/s |
802.11n data rate: AP6010DN-AGN: 2.4GHz and 5GHz AP6010SN-GN：2.4GHz |
GI=800ns | GI=400ns |
| 20MHz rate (Mb/s) | 40MHz rate (Mb/s) | 20 MHz (Mb/s) | 40MHz rate (Mb/s) |
| 6.5 @ MCS10 | 13.5 @ MCS0 | 7.2 @ MCS0 | 15 @ MCS0 |
| 13 @ MCS1 | 27 @ MCS1 | 14.4 @ MCS1 | 30 @ MCS1 |
| 19.5 @ MCS2 | 40.5 @ MCS2 | 21.7 @ MCS2 | 45 @ MCS2 |
| 26 @ MCS3 | 54 @ MCS3 | 28.9 @ MCS3 | 60 @ MCS3 |
| 39 @ MCS4 | 81 @ MCS4 | 43.3 @ MCS4 | 90 @ MCS4 |
| 52 @ MCS5 | 108 @ MCS5 | 57.8 @ MCS5 | 120 @ MCS5 |
| 58.5 @ MCS6 | 121.5 @ MCS6 | 65 @ MCS6 | 135 @ MCS6 |
| 65 @ MCS7 | 135 @ MCS7 | 72.2 @ MCS7 | 150 @ MCS7 |
| 13 @ MCS8 | 27 @ MCS8 | 14.4 @ MCS8 | 30 @ MCS8 |
| 26 @ MCS9 | 54 @ MCS9 | 28.9 @ MCS9 | 60 @ MCS9 |
| 39 @ MCS10 | 81 @ MCS10 | 43.3 @ MCS10 | 90 @ MCS10 |
| 52 @ MCS11 | 108 @ MCS11 | 57.8 @ MCS11 | 120 @ MCS11 |
| 78 @ MCS12 | 162 @ MCS12 | 86.7 @ MCS12 | 180 @ MCS12 |
| 104 @ MCS13 | 216 @ MCS13 | 115.6 @ MCS13 | 240 @ MCS13 |
| 117 @ MCS14 | 243 @ MCS14 | 130 @ MCS14 | 270 @ MCS14 |
| 130 @ MCS15 | 270 @ MCS15 | 144.4 @ MCS15 | 300 @ MCS15 |
explain: MCS index: modulation and coding scheme (MCS) index, which determines the number of space streams, modulation, coding rate and data rate values. GI: guard interval between symbols (GI), which helps the receiver overcome the impact of multipath delay. |
| AP6010DN-AGN receiving sensitivity | 2.4 GHz 802.11b (CCK) -97 dBm @ 1 Mb/s -92 dBm @ 2 Mb/s -92 dBm @ 5.5 Mb/s -90 dBm @ 11 Mb/s | 2.4 GHz 802.11g (non-HT20) -92 dBm @ 6 Mb/s -91 dBm @ 9 Mb/s -90 dBm @ 12 Mb/s -87 dBm @ 18 Mb/s -83 dBm @ 24 Mb/s -80 dBm @ 36 Mb/s -76 dBm @ 48 Mb/s -74 dBm @ 54 Mb/s | 2.4 GHz 802.11n (HT20) -92 dBm @ MCS0/8 -89 dBm @ MCS1/9 -86 dBm @ MCS2/10 -82 dBm @ MCS3/11 -79 dBm @ MCS4/12 -74 dBm @ MCS5/13 -73 dBm @ MCS6/14 -71 dBm @ MCS7/15 | 2.4 GHz 802.11n(HT40) -89 dBm @ MCS0/8 -86 dBm @ MCS1/9 -83 dBm @ MCS2/10 -79 dBm @ MCS3/11 -76 dBm @ MCS4/12 -72 dBm @ MCS5/13 -70 dBm @ MCS6/14 -68 dBm @ MCS7/15 |
5 GHz 802.11a (non-HT20) -89 dBm @ 6 Mb/s -88 dBm @ 9 Mb/s -85 dBm @ 12 Mb/s -83 dBm @ 18 Mb/s -80 dBm @ 24 Mb/s -76 dBm @ 36 Mb/s -71 dBm @ 48 Mb/s -70 dBm @ 54 Mb/s | 5 GHz 802.11n (HT20) -88 dBm @ MCS0/8 -85 dBm @ MCS1/9 -84 dBm @ MCS2/10 -77 dBm @ MCS3/11 -74 dBm @ MCS4/12 -70 dBm @ MCS5/13 -68 dBm @ MCS6/14 -67 dBm @ MCS7/15 | 5 GHz 802.11n (HT40) -85 dBm @ MCS0/8 -80 dBm @ MCS1/9 -78 dBm @ MCS2/10 -74 dBm @ MCS3/11 -71 dBm @ MCS4/12 -67 dBm @ MCS5/13 -65 dBm @ MCS6/14 -63 dBm @ MCS7/15 |
| AP6010SN-GN receiving sensitivity | 802.11b (CCK)： -97 dBm @ 1 Mb/s -92 dBm @ 2 Mb/s -92 dBm @ 5.5 Mb/s -90 dBm @ 11 Mb/s | 802.11g (non-HT20)： -92 dBm @ 6 Mb/s -91 dBm @ 9 Mb/s -90 dBm @ 12 Mb/s -87 dBm @ 18 Mb/s -83 dBm @ 24 Mb/s -80 dBm @ 36 Mb/s -76 dBm @ 48 Mb/s -74 dBm @ 54 Mb/s | 802.11n(HT20)： -92 dBm @ MCS0/8 -89 dBm @ MCS1/9 -86 dBm @ MCS2/10 -82 dBm @ MCS3/11 -79 dBm @ MCS4/12 -74 dBm @ MCS5/13 -73 dBm @ MCS6/14 -71 dBm @ MCS7/15 | 802.11n(HT40)： -89 dBm @ MCS0/8 -86 dBm @ MCS1/9 -83 dBm @ MCS2/10 -79 dBm @ MCS3/11 -76 dBm @ MCS4/12 -72 dBm @ MCS5/13 -70 dBm @ MCS6/14 -68 dBm @ MCS7/15 |
Networking application
It can provide high-performance wireless services for occasions with moderate area, relatively concentrated users and enterprise level scenarios with large demand for capacity. This type of equipment can be flexibly distributed according to different environments. AP6010DN-AGN can also work in the mixed mode of AP and bridge.
AP6010DN-AGN and AP6010SN-GN support two working modes Fat AP and Fit AP, and can flexibly switch between Fat AP and Fit AP according to the needs of network planning.
When the initial scale of the customer's wireless network is small, the customer only needs to purchase AP equipment and set its working mode to Fat AP mode. With the continuous expansion of the customer's network scale, when the number of AP devices applied in the network reaches tens or even hundreds, in order to reduce the complexity of network management, it is recommended that the customer purchase wireless controller devices to facilitate centralized management of all AP devices in the network. At this time, it is necessary to switch its AP working mode to Fit AP mode.
Fit AP typical networking diagram (access point mode)
In the above networking, the device, as a Fit AP, only carries the bridging and forwarding function. User access, AP online, authentication, routing, AP management, security protocol, QoS and other functions need to be completed in cooperation with the AC.
Fit AP WDS typical networking diagram (bridge mode - point-to-point)
Fit AP WDS typical networking diagram (bridge mode - point to multipoint)
In the above networking, the equipment connects two or more independent wired LANs or wireless LANs through wireless links to form an interworking network to achieve data access. The WDS mode can support point-to-point and point to multipoint networking. Through 5G and 2.4G dual RF, the AP can realize business applications such as wireless bridge and access.
Fit AP Mesh typical networking diagram
In the above networking, the AP as the mesh node MP (Mesh Point) forms a self configuring and self-healing wireless mesh network WMN (Wireless Mesh Network) backbone through mesh interconnection, and provides the connection to the Internet through the AP with gateway function as the mesh portal node MPP (Mesh Portal Point). The terminal node can access the WMN network through the access service of the AP. Due to the existence of a dedicated Mesh routing protocol, its transmission quality can be better guaranteed, and it is more suitable for scenarios requiring high bandwidth and high stability Internet connections.
Typical networking diagram of Fat AP
In the above networking, the device, as a Fat AP, independently completes user access, authentication, data security, service forwarding, QoS and other functions.
