Electronic Engineering World Electronic Engineering World Electronic Engineering World

AD711TH

Device model AD711TH
Product category Analog mixed signal IC    Amplifier circuit   
file size 5975.92 of 16
manufacturer ADI
Official website address https://www.analog.com
Go to download Detailed parameters

Device replacement

Device name manufacturer describe
Sorry, there is no substitute material information

AD711TH parameter description

Basic information of AD711TH amplifier:

AD711TH is an Operational AMPLIFIER. The common packaging method is HERMETIC SEALED, METAL CAN, TO-99, 8 PIN

Core information of AD711TH amplifier:

The minimum operating temperature of AD711TH is - 55 ° C, and the maximum operating temperature is 125 ° C. The maximum bias current at the peak return temperature of NOT SPECIFIED25 ℃ is 0.0001 µ A, the maximum average bias current is 0.00005 µ A, and the maximum input offset current (IIO) is only 0.026 µ A

How to simply look at the efficiency of an amplifier? According to its slewing rate, the nominal slewing rate of AD711TH is 20 V/us. The maximum slew rate of AD711TH given by the manufacturer is 3 mA, while the minimum slew rate is 18 V/us. The minimum voltage gain is 200000. When the operational amplifier is used in closed loop, the frequency is 4000 kHz when the AD711TH gain becomes 0.707 times the low-frequency gain under a given closed loop gain (generally 1, 2, 10, etc.).

The nominal supply voltage of AD711TH is 15 V, and the corresponding nominal negative supply voltage is - 15 V. The input offset voltage of AD711TH is 500 µ V (input offset voltage: the compensation voltage required to make the output terminal of the operational amplifier 0V (or close to 0V) between the two input terminals.)

Relevant dimensions of AD711TH:

AD711TH has 8 terminals. The terminal location type is BOTTOM. Total pins: 8

Other information of AD711TH amplifier:

AD711TH adopts the architecture of VOLTAGE-FEEDBACK. It belongs to low offset amplifier. It is not a low dropout amplifier. The frequency compensation of AD711TH is YES. Its temperature class is: MILITARY.

AD711TH does not meet Rohs certification. The corresponding JESD-30 code is O-MBCY-W8. The corresponding JESD-609 code is e0. The packaging code of AD711TH is TO-99. The packaging material of AD711TH is mostly METAL.

Its package shape is ROUND. AD711TH package pins are in the form of CYLINDRICAL. The terminal forms are: WIRE.

WEBENCH design process+simple 5V to 3.3V DCDC converter design
1、 Before design, first determine what to design. Since the current mainstream monolithic integrated chips have adopted 3.3V or lower power supply voltage, the original popular 5V power supply can no longer meet these requirements. Therefore, the design content is to design a DCDC reducing circuit that converts easily available DC5V to DC3.3V, and the maximum output power can reach 300mA II Tools to be used: TI's online design software WEBENCH III. Enter the software homepage through the following link: http://www.ti.com.cn/lsds/ti_zh/analog/webench/overview.page You can see the whole interface in the figure above
bobde163 Analog and mixed signals
DFRobot Gravity: AS7341 Evaluation Summary
Activity details: https://bbs.eeworld.com.cn/elecplay/content/151 Summary of evaluation report: @ jinglixixi [Gravity: AS7341 evaluation]+first acquaintance of visible light sensor AS7341 [Gravity: AS7341 evaluation]+comparative analysis between color sensors [Gravity: AS7341 evaluation]+selection of driving development board [Gravity: AS7341 evaluation]+detection of sensor color value [Gravity: AS7341 evaluation]+detection of frequency value
okhxyyo Domestic chip communication
Details and parameters of ZigBee module
The detailed information and parameters of ZigBee module are expected to be useful to everyone! Details and parameters of ZigBee module
linyou1120 RF/Wireless
The STM32 reads SPIFLASH??
Chip: STM32F107 (72Mhz) FLASH: AT45DB161D has now written "1234" four characters. When setting SPI_BaudRatePrecaler to SPI_BaudRatePrecaler_256, it reads 0x000x310x320x330x34..... When setting SPI_BaudRatePrecaler to SPI_BaudRatePrecaler_2, it reads 0x000x320x330x34..... What's wrong??? Single step debugging
wwbinww stm32/stm8
How should analog ground and digital ground be connected?
In PCB circuit board, there are analog ground AGND and digital ground DGND. What connection should be used between these two grounds? Use a 0 ohm resistor, a magnetic bead, or something else? What is the theoretical reason? How should analog ground and digital ground be connected? Personal habit is to connect with magnetic beads. When PCBlayout is used, the capacitance 0 Ω, magnetic beads, capacitors, inductors and isolation belts near the two ends of the magnetic beads can be placed according to the specific circuit. When the impact is not significant at low frequencies, the digital power supply and the analog power supply should be separated, and the ground wires should be arranged separately. When the single point grounding is high frequency, the magnetic beads are the best choice. In theory, it is to restrain the influence of high-frequency noise on analog circuit, reduce the impedance of ground circuit, and reduce the noise of ground circuit
Boiling wine in troubled times Analog electron
ULisp microcomputer
TinyLispComputer2 (uLisp microcomputer) is a small independent device based on ATmega1284, with its own display and keyboard, which can be used to program in uLisp. See TinyLispComputer2 on Technology for details. Specification display: 21 characters x 8 lines. Available memory: 3001 Lisp units (12004 bytes). EEPROM: 1024Lisp unit (4K bytes). Language: uLisp is a subset of CommonLisp, with 125 Lisp functions and
dcexpert MicroPython Open Source

Copyright Electronic Engineering World Beijing B2-20211791 Jing ICP Bei 10001474-1 TSSP [2006] No. 258 Jinggong Network Anbei No. 11010802033920 Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved