Electronic Engineering World Electronic Engineering World Electronic Engineering World

KA201A

Device model KA201A
Product category Analog mixed signal IC    Amplifier circuit   
file size 1112.48 of 3
manufacturer SAMSUNG
Official website address http://www.samsung.com/Products/Semiconductor/
Go to download Detailed parameters

Device replacement

Device name manufacturer describe
KA201A Fairchild Semiconductor Corporation KA201A is an Operational AMPLIFIER. The common packaging method is DIP-8KA201A, with a minimum working temperature of - 25 ° C and a maximum working temperature of 85 ° C. Its peak reflux temperature is NOT SPECIFIED2

KA201A Parameter Description

Basic information of KA201A amplifier:

KA201A is an Operational AMPLIFIER. The common packaging method is 0.300 INCH, DIP-8

KA201A amplifier core information:

The minimum operating temperature of KA201A is - 25 ° C, and the maximum operating temperature is 85 ° C. Its peak return temperature is NOT SPECIFIEDThe maximum bias current at 25 ℃ is 0.075 µ A Its maximum average bias current is 0.1 µ A

The maximum voltage swing rate of KA201A given by the manufacturer is 2.5 mA. Its minimum voltage gain is 25000.

The nominal power supply voltage of KA201A is 15 V, and the corresponding nominal negative power supply voltage is - 15 V. The input offset voltage of KA201A is 3000 µ V (input offset voltage: the compensation voltage between the two input terminals required to make the output terminal of the operational amplifier 0V (or close to 0V).)

Relevant dimensions of KA201A:

The width of KA201A is 7.62 mm and the length is 9.2 mm. KA201A has 8 terminals. Its terminal location type is DUAL. The terminal pitch is 2.54 mm. Total pins: 8

Other information of KA201A amplifier:

KA201A adopts the architecture of VOLTAGE-FEEDBACK. It is not a low dropout amplifier. The frequency compensation of KA201A is NO. Its temperature class is: OTHER. KA201A does not meet Rohs certification.

It contains lead. The corresponding JESD-30 code is R-PDIP-T8. The corresponding JESD-609 code is e0. The packaging code of KA201A is DIP. The packaging material of KA201A is mostly PLASTIC/EPOXY.

Its package shape is RECTANGULAR. KA201A package pins are in the form of IN-LINE. The terminal forms are THROUGH-HOLE. The maximum height of the seating surface is 5.08 mm.

Problem of FPGA HDL code mapping to unit circuit
After the HDL code is written, it should be mapped into some basic timing or combinational circuits in FPGA implementation. Is there any internal rule when mapping? The problem of FPGAHDL code mapping to unit circuit must have internal compilation rules, such as IFELSEIFELSIFENDIF, which results in compiler compiling to cascade selectors
eeleader FPGA/CPLD
Do you know what the LM3S8962 interrupt process and response code is under ucos2?
Do you know the process of LM3S8962 interrupt response under ucos2 (before entering the interrupt service program) and the corresponding code? I read it for a long time and didn't understand it. Thank you for your advice! Do you know what the LM3S8962 interrupt process and response code is under ucos2? It is similar to setting interrupts when streaking naked. Thank you for replying to the post of owner zhypabc! My understanding is that there should be a switching process with the task when the response is interrupted, and the ucos should have a response processing process. I am also troubled by this problem when replying to the sofa Study_Tellaris post! Only UCOS2 on ARM7tdmi core has been studied
zhypabc Microcontroller MCU
Microcontroller small production
Suitable for beginners Write a general content about the small production of single chip microcomputer Re: small production of single chip microcomputer
zhaobqing163 singlechip
Can I input PWM mode at the same time for incense, TIMx_CH1 and TIMx_CH2
Can CH1 and CH2 of the same TIM do PWM mode input at the same time, and can CH3 and CH4 do output comparison mode output when CH1 and CH2 do PWM input? Incense version, can TIMx_CH1 and TIMx_CH2 do PWM mode input at the same time When you measure a PWM input first, you will use two channels at the same time (although you only need to connect to the input pin of one channel), one to measure the frequency and the other to measure the duty cycle. But when you use CH1 and CH2 to make a PWM input, CH3 and CH4 can be used for output comparison
allensun006 stm32/stm8
[Zhaoyi GD32H759I-EVAL] CAN2 communication transceiver test
Send and receive test of CAN2 interface on test development board. 1、 Hardware part 1.1, chip manual part 1.1.1, chip peripheral block diagram CH32H759 has three CAN communication interfaces 1.1.2, CAN introduction CAN (Controller Area Network) bus is a bus standard that can realize mutual communication between microprocessor and equipment without host. CAN network interface supports CAN bus protocol 2.0A/B, ISO11898-1:2015 specification and BOSCHCAN-FD specification. CAN bus control
TL-LED Domestic chip communication

Copyright Electronic Engineering World Beijing B2-20211791 Jing ICP Bei 10001474-1 TSSP [2006] No. 258 Jinggong Network Anbei No. 11010802033920 Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved