Electronic Engineering World - Forum » forum › Electronic technology exchange › Analog electron › TJA1042

Read thirteen thousand five hundred and seventy | return four

fourteen million one hundred and one thousand six hundred and three

fifty Posts	forty-two TA resources

A grain of gold sand (medium)

Building owner

Published on 2018-10-5 11:58 Only the author

TJA1042 [Copy Link]

What is the use of SPILT pin of TJA1042 chip? How did Pingshiduo answer the question? Can you be more specific?

1.png (20.11 KB, Downloads: 0)

This post is from Analog Electronic Forum

Latest reply

Little sun yy

Nobody answered you, brother details reply Published on 2021-11-19 14:04

give the thumbs-up follow (1)

Simulation Technology Forum Fundamentals of Analog Electronic Technology

report

qewnja

forty-four Posts	five TA resources

A grain of gold sand (medium)

sofa

Published on 2018-10-7 20:55 Only the author

This pin is used to balance the network. In most cases, it can be suspended. I usually suspend it

This post is from Analog Electronic Forum

Personal signature http://www.miractech.com , bus isolation module, vibration displacement sensor

Analog electronic data Analog electronic circuit diagram Analog Electronic Technology

report

leafhsh

seven Posts	zero TA resources

A grain of gold sand (medium)

Bench

Published on 2018-12-7 09:28 Only the author

Pin 5 thinks that it should be connected to high level. When my test board is suspended, the chip does not work during the test.

This post is from Analog Electronic Forum

report

lihilong

seven Posts	zero TA resources

A grain of gold sand (primary)

four floor

Published at 10:16, 2020-2-21 Only the author

Let me ask you another question. How does the main chip know that there is a message on the bus when the chip is in standby? How does this standby function work?

This post is from Analog Electronic Forum

report

Little sun yy

six hundred and seventy-eight Posts	zero TA resources

Pure silicon (advanced)

five floor

Published on 2021-11-19 14:04 Only the author

Nobody answered you, brother

This post is from Analog Electronic Forum

report

Back to list Send new posts reply

Guess you like it

PADS VX2.7 Little White Zero Basic Introduction PCB Layout Design 52 practical courses

Altium Designer 22 Introduction to Electronic Design 56 Lectures

Electrical Foundation

Circuit (Jiangsu University)

Cadence Allegro 22.1 Programming Downloader ST_LINK Complete PCB Design Tutorial

activity More>>

look around

[AutoChips AC7801x motor demo board evaluation] Unpacking and hardware circuit learning
Unpacking and hardware learning The popular circuit board after unpacking is very pleasing. The overall design is divided into two parts, and the middle is separated by flat wires. [attach] 509795 [/attach] [attach] 509796 [/attach] [attach] 509797 [/attach] [attach] 509798 [/attach] The hardware learning hardware is ac7801x_lqfp48_motor_v1.1, and the onboard AC7801x chip
Does anyone know the difference between CAN transceiver TJA104x
Now I'm choosing the following IC as the board. I haven't come to read the manual. Who knows their difference {: 1_96:} TJA1041, TJA1042，TJA1043，TJA1044，TJA1045，
How to coordinate the ground of switch tube and control branch of switching power supply?
[attach] 820483 [/attach] [attach] 820482 [/attach] Figure 1 shows that a buck circuit is made with TITA-TI, OUT1 is the voltage waveform of the drive branch, and a power supply is used. Figure 2 shows a BUCK circuit made with LTspice. V (out1) - V (out2) is the voltage waveform of the drive branch and also uses a power supply. Look at the circuit topology. The ground of the main circuit is the power supply
The simulation result of super simple circuit is incorrect
Evaluation shortlist: 2 new products of STM32H5 series NUCLEO H533RE were evaluated
[Play with C2000 LaunchPad] ADC Tips
Advantages and applications of variable frequency power supply
How does Python link MySQL?
Hard disk MP3 multi-function digital companion
Shandong Electronic Design Competition Group 262370303 Welcome to join