Product description
|
Product composition and characteristics
|
This product is made of specially synthesized inorganic silicate solution Aluminum silicate Fiber, heat reflective material and selected hollow Glass It is made of micro beads. coating It is an inorganic single component, non-toxic and harmless. The thermal conductivity of the coating is very low, only 0.033W/m.k. The thermal insulation effect is obvious, and the inhibition efficiency can reach about 90% under certain thickness conditions. It can also effectively keep cold for low-temperature objects, and effectively restrain the temperature rise of low-temperature objects caused by external heat sources due to heat conduction.
|
Working mechanism
|
The overall structure of the coating is equivalent to creating the heat preservation and insulation mechanism of the thermos ceramics When heated at high temperature, the air inside the microsphere cavity will not produce thermal convection. Hollow ceramic beads are closely arranged and there is a three-dimensional air layer between them, which also avoids the generation of thermal convection. Inorganic with relatively low thermal conductivity Film-forming substance As the support of the coating, the thermal insulation shielding layer with static air layer and inorganic film-forming material is jointly constructed. The heat reflective material is added as an auxiliary filler, so that the thermal conductivity of the coating is close to the vacuum thermal conductivity, which plays an effective role in thermal insulation.
|
Typical use
|
High temperature kiln and furnace; High temperature mold, pipeline, electric furnace, induction furnace, rotary kiln, etc.
|
Yan colour
|
ash
|
|
project
|
index
|
Test/Standard
|
Paint appearance
|
Pasty ash
|
Visual inspection
|
Paint components
|
One component
|
|
density
|
1.4g/cm three
|
Measured
|
Film processing performance
|
sure
|
|
This product is a single component product cured at room temperature. It can be used after being opened and stirred evenly. The unused products are put into a plastic bucket or plastic bag for sealing and storage. When the construction interval is long, the construction tools shall be cleaned to prevent consolidation of construction tools.
N All products under normal storage and within the warranty period conform to the data listed in the table above.
|
Coating performance
|
project
|
Test standard
|
performance parameter
|
Film appearance
|
Visual inspection
|
Graininess
|
colour
|
Visual inspection
|
pale
|
Dry density
|
JGJ/T 70-2009
|
1.3 g/cm three
|
drying time
|
GB/T 1728-1979
|
Surface drying for 2h and actual drying for 24h
|
Film hardness
|
GB/T 6739-2006
|
5H
|
Compressive strength
|
GB/T 5072-2008
|
≤80MPa
|
Bond strength (adhesion)
|
GB/T5210-2006
|
8MPa
|
Tensile strength (after high temperature)
|
GB/T 5210-2006
|
8MPa
|
thermal conductivity
|
GB/T 10297-2015
|
0.033W/m.k
|
hot test
|
QB/C001-2005
|
1000℃
|
Recommended film thickness
|
Film thickness and coating rate
|
Dry film thickness
(μ m )
|
Theoretical Coverage
(㎡ /kg/mm )
|
constant
|
With actual working condition
|
one
|
Recommended coating to design thickness
|
|
Ensure that the painted surface is free of dust, oil stain, rust, brittle layer and other foreign matters, and ensure that the painted surface is clean and dry without pollution. Polish and roughen the coated surface as much as possible to ensure the surface roughness within the range of 25-40 μ m. If the metal surface is manually polished to St3 or sandblasted to Sa2.5, the coating effect will be better.
|
Construction method
|
spray:
|
|
Air spraying with large caliber spray pots
|
Brushing:
|
|
Brush with cross method.
|
|
diluent / Cleaning agent
|
|
Deionized water
|
|
Surface drying time
|
Practical time
|
|
≤2h
|
≤24h
|
|
N Table dry time and actual dry time according to GB/T1728-1989 Measured.
N The above data are measured based on 1mm film thickness.
N In practical application, drying time is related to film thickness and construction environment.
|
|
|
15kg/ Barrel and iron drum packaging
|