Features of Jilin Sealant Products
GST modified epoxy potting adhesive
Grouter for sealing rubber base plug
Features of sealant products
This product has high hardness, good polishing, fast curing speed, strong adhesion, and is easy to mix with concrete, stone
Materials, steel plates and other base materials can be bonded at low temperature (- 10 ℃ - 45 ℃).
![](https://img2.bmlink.com/big/supply/2017/3/13/9/569304610402.jpg)
![](https://img2.bmlink.com/big/supply/2017/3/13/9/569304610402.jpg)
![](https://img2.bmlink.com/big/supply/2017/3/13/9/569304610402.jpg)
![](https://img2.bmlink.com/big/supply/2017/3/13/9/569304610402.jpg)
![](https://img2.bmlink.com/big/supply/2017/3/13/9/569304610402.jpg)
![](https://img2.bmlink.com/big/supply/2017/3/13/9/569304610402.jpg)
![](https://img2.bmlink.com/big/supply/2017/3/13/9/569304610402.jpg)
Product use
It is suitable for filling structural micro cracks>0.5mm, as well as for mortar, concrete and brick hollowing
Grouting and reinforcement treatment shall be carried out for cracks and other conditions.
Executive standard GB50367-2006
construction technology
1、 Material allocation:
1. Mix and mix evenly according to the proportion of component A: component B=4:1, and then use.
2. According to the actual crack width and construction conditions on site, a proper amount of dilute can be added into the epoxy resin mixture
Dilute the release agent (such as acetone, xylene, or special resin diluent) to reduce the
Grease viscosity, easy to pour.
3. The one-time mixing amount should be no more than 500g. It should be used whenever it is prepared. The initial setting should be 24h, and the full curing should be 5-7 days,
If the one-time mixing amount is too much, the initial setting time will be shortened accordingly.
matters needing attention
1. This product is applicable to the environment above 5 ℃. Temperature rise measures must be taken when the temperature is below 5 ℃.
2. When there is water on the concrete surface, it shall be wiped off and dried with a hot air blower.
3. Pay attention to ventilation in the use place, and wear protective glasses, gloves and tightener when using
Wash hands immediately after using this product.
4. In the process of construction, if it is accidentally splashed on the surface or in the eyes, it should be immediately washed with a large amount of water
Those who are serious should seek medical advice in time.
Packaging, storage and transportation
1. This product is packed in iron drums, and the packaging specification is 12kg 3kg/group for each set, or 4kg 1kg/group for each set.
2. This product is not flammable and dangerous. It can be transported by air, * * * and road. It should be light during transportation, loading and unloading
Keep it away from rain, sun and upside down.
3. The product is stored at room temperature and has a shelf life of 12 months. If it exceeds the shelf life, it can still be used after passing the test
use.
![](https://img2.bmlink.com/big/supply/2017/3/21/10/548635614360047.jpg)
Product use
1. It is used to seal various concrete cracks, joints of steel plates and various brick plates, and for non important structures
The reinforcement at the position shall be embedded and fixed.
2. It is used to seal the cracks and bond the base in the grouting repair construction of concrete structure cracks.
Executive standard GB50367-2006
usage method
Take 100 parts of material A and 3 parts of material B (curing agent). Mix and mix well before use.
matters needing attention
1. The surface of the adhesive shall be clean, dry and free from looseness, oil stain, etc.
2. When the product is placed in a fire, it will react violently and release carbon monoxide and carbon dioxide.
3. The amount of curing agent can be increased or reduced appropriately according to actual needs to control the curing speed.
4. When mixing materials, it is better to mix them at any time, and it is not allowed to mix all materials A and B at one time.
5. If it is not used up at one time, the cover must be covered after use so that it can be reused next time.
★ Relationship between fracture width and injection port spacing
Crack width (mm) 0.1-0.3 0.3-0.5 0.5-1.0 1.0-3.0
Injection port spacing (mm) 10-20 20-30 30-40 40
![](https://img2.bmlink.com/big/supply/2017/3/22/8/969499308136059.jpg)