1、 Product parameters:
model | SWH-6100500C |
Specifications | 1000 * 600* 15mm |
Rated power | 500W±10% |
Rated voltage | 220V±10% |
Heating area | 4-8 square meters |
weight | 4KG/piece |
Installation environment | Interior wall |
2、 Product advantages
1. Three advantages
● Easy installation: 2 hours of warm installation at home, and the decorated residence can be easily installed
● Good and comfortable: 5 ° C - 25 ° C can be adjusted at will, soundless, windless, dustless, dry, strong and far-infrared
● Low cost: installation cost is half lower than that of floor heating, starting from one room, and the use cost is lower than that of central heating and air conditioner 30% - 50% lower (national standard energy-saving residence)
2. Three safety guarantees
● Environmental protection and safety: SGS environmental protection certification, without any benzene , formaldehyde and other VOC emissions
● Electrical safety: certified by National Infrared Center, with breakdown resistance voltage up to 3750V
● Anti overheating safety: built-in temperature limit protection, automatic power off for overheating
3. Two major operational guarantees
● High tech carbon crystal * * * technology, more advantageous carbon crystal manufacturing process
● 10 year warranty, 100000 hour service life
3、 Questions and answers of relevant persons
1. Fast principle of Haihua wall heating products
The electric heating conversion rate of Haihua wall heating products is close to 1:1, which is very energy-saving, ensuring that the energy utilization rate of the products is optimized to achieve the goal of both fast and energy saving. The details are as follows:
① Haihua wall heating products are heating elements with large heat dissipation surface at present, thus ensuring high thermal efficiency and ultra fast temperature rise;
② Haihua wall heating products are field effect products, with small radial current, no impedance heat loss of electric wire products, and no heat loss of exhaust gas emissions of boiler products, which makes its energy utilization rate larger and temperature rise faster;
③ The heating mode of Haihua wall heating products is mainly infrared radiation (up to 97%), and the heating mode is more direct; The temperature gradient with the heated body is small, the path loss is low, and the temperature rise is ultra fast;
④ Haihua wall heating products belong to low-temperature heating materials, which have poor heat retention, can be heated immediately after being electrified, and can quickly transfer heat to the receptor to a large extent;
⑤ The installation is fast, and it can be completed in one day by two people of 100 square meters.
2. Benefits of using Haihua wall heating
① The heating of Haihua wall heating products is extremely fast, 500 watts/piece, fast heating. The heating core can quickly heat up 1 minute after power on, and 50 degrees in 5 minutes, which is unmatched by traditional heating;
② Haihua wall heating products can save energy. Since each room is equipped with a temperature controller, the time can be set automatically switch When people leave the room, they can close or adjust to the energy saving state. When they return home, they can open it again to make heat quickly, which greatly reduces the use cost of customers.
3. Energy consumption of Haihua heating products
How to understand energy consumption
① Energy consumption, generally speaking, is the power consumption, which is equal to the heat dissipation of the house;
② The heat dissipation of the house refers to the heat lost through the house from the heating equipment;
③ The heat dissipation is only related to the thermal insulation condition of the house itself and the temperature difference between indoor and outdoor, and has nothing to do with the wall heating system;
④ The energy consumption of wall heating products in energy-saving residential buildings will be significantly lower than that in non energy-saving residential buildings (more than 50% lower);
⑤ Due to the different outdoor temperature values, the energy consumption of each month is also quite different. For example, January is generally a cold winter, when the energy consumption of wall heating system is relatively high, the calculated energy consumption should be the average value of the whole heating cycle.
⑥ For residential buildings that meet the national energy conservation standards, when the system is in normal use, the building area is 100 square meters, the indoor temperature is set at 16-18 degrees, and the average monthly electricity charge in a winter is 700-800 yuan (the electricity price is based on an average of 0.5 yuan per degree);
What is energy-saving residence and how to standardize the use of wall heating
① Simple judgment method for residential buildings conforming to the national building energy conservation code: the external wall of the house is insulated, window Household Double insulating glass Windows (the national building energy conservation code has been enforced since 2005);
② Generally, houses without external wall insulation, non double glass windows, very high floors, old bungalows, large glass curtain walls, etc. can be regarded as non energy-saving houses;
③ The temperature set at the initial opening shall be set at 18 ℃, and shall be used until the thermostat automatically stops, so as to eliminate the cold radiation from the four walls and the top floor of the room; The internal wall heating system works at full load during this period, and the energy consumption is relatively high; After that, the system can be used normally;
④ . Because the internal wall is generally without insulation, the heat will be lost from the room with wall heating turned on to other rooms, so a single room in the house uses wall heating, and the overall energy consumption is higher than that of the previous year; If the house is located at the top, bottom or side of the whole building, or the adjacent residential buildings are uninhabited, the energy consumption will be significantly higher, and the energy consumption of individual residential buildings or bungalows will be higher;
⑤ In normal use, it is generally recommended to set the energy-saving temperature at 16 ℃ - 18 ℃. If the temperature is set high, the indoor and outdoor temperature difference will be increased, and the year-on-year energy consumption will also increase significantly.
4. How to use more energy saving
Behavioral energy saving (energy saving 10-30%):
① . In the morning room, open the curtains in the daytime to receive solar heat, and close the curtains in the cloudy and evening days to reduce heat loss (significant energy saving of 20-30%);
② . Since opening windows for ventilation will lose a lot of heat in a short time, and the energy consumption will increase significantly, it is recommended to close the doors and windows when opening the wall heating, try to reduce the number of times of opening windows for ventilation, and close the door when people enter and exit;
③ If there are not many family members, it is recommended to close or lower the wall heating in the unattended area after falling asleep, and try to use the Chaoyang room;
④ When there is no one in the room or you leave, you can turn off or set the temperature value at 8 ℃ to insulate the house. When you return, you can turn on or restore the normal temperature value. It is recommended to use an intelligent temperature controller for automatic control.
Increase thermal insulation measures (can significantly save energy by 30-50%):
① . Double thick curtains with reflective layer should be installed indoors. If possible, it is recommended to stick glass reflective film on the glass or nail a layer of transparent plastic paper outside the window at the same time;
② Check and replace the sealing strips of doors and windows to ensure the sealing of doors and windows and reduce heat loss. If possible, replace the windows with double insulated glass plastic steel windows;
③ Install thermal insulation materials on the internal and external walls of the house to improve the thermal insulation effect of the wall;
④ For buildings with very high floors or flat roofs, it is recommended to add suspended ceilings and thermal insulation layers in the suspended ceilings to improve the thermal insulation effect of the roof.
5. What is the ratio for general home installation?
For general household installation, the actual heating area of the house is calculated according to the power ratio of 100-120 watts per square meter. For rooms with small space such as bedrooms and study, the power ratio can be about 100 watts per square meter (calculated according to the heating area, the heat preservation is relatively good), The space with large glass sliding doors or windows (relatively poor thermal insulation effect) in large places such as the living room and dining room is 120 watts per square meter. For example, the actual heating area of a house with a building area of 140 square meters that meets the national standard of building energy efficient residence is about 90-100 square meters, In this way, the whole house is full and only about 20-25 walls are warm. The overall installation cost is very cost-effective.
