Factory operation of 25KW diesel generator GT-25TSI High quality, low fuel consumption, low noise, large output power, reliable performance, small size, light weight. Its reliable stability, economy, power, durability and environmental safety are welcomed by users at home and abroad. The Sino Italian joint venture generator set is small in size, light in weight, low in fuel consumption, high in power, reliable in operation and convenient in maintenance. The electronic governor is adopted, with protection functions such as high cooling water temperature, low oil pressure, speed alarm and automatic shutdown.
1. Simple structure, light volume, no vulnerable components, life-long maintenance free. Force reduction machine
2. No heating components, low temperature rise, no energy consumption. Consumption terminal wave low heat 3
3. The voltage waveform is good, and the waveform distortion rate is less than 5% under no load, and less than 3% under load. The quality has low waveform heat. It can be applied to precision electric field stations with high requirements for electric quality.
4. Strong inductive load capacity, capable of dragging inductive load equal to its own capacity.
Factory operation of 25KW diesel generator GT-25TSI How to set battery charging for static generator?
How to regulate the charging of static generator sets?
1。 Charging mode of static generator set.
When charging, the battery should be tightened, and the positive and negative terminals of the charger should be connected with the positive and negative terminals of the battery. There are two ways to charge the battery of the silent generator, one is based on the technical performance of the device and the charging storage of the charging device.
The number of batteries has stopped.
2。 Charging standard of mute generator set.
(1) Initial expenses
Charging refers to the secondary charging of the battery before use. The initial charging current and time of the silent generator shall be strictly in accordance with the manufacturer's regulations. Under normal circumstances, the current of the initial charge should not be too large. Because of the current, the temperature of the electrolyte can be too high or damaged.
Plates and baffles affect the composition of active substances. When the ambient temperature is high, the charging current should be reduced.
(2) Normal charging
Normal charging is to charge the battery after use. Before charging the static generator, carefully check the voltage and electrolyte ratio of the single battery. When the liquid level is lower than the rule specification, it should be added with distilled water in time to stop charging.
The normal charging current shall stop in two stages. The phase of the charging current is 1/10 of the battery capacity. After 10~12h, when the electrolyte is charged into the voltage of a single battery, it is 23~24V. Then the charging current phase is the charging current. stage
The charging current is 1/2 of the level 1 charging current, lasting for 4~6h. If the voltage of a single battery reaches 26~27V, the proportion and voltage of electrolyte will not change within 2h, a large number of bubbles will appear, and the battery will be fully charged.
technical parameter
*、 Product model: GT-25TSI
*、 Rated power KW ：25
*、 Standby power KW ：26
*、 Rated frequency HZ ：50
*、 Rated voltage V ：AC400
*Startup mode: electric startup
*Organization type: silent
*Power factor: 0.8/1.0
*、 mutually number : Three phase
*Fuel model: 0 # summer 、 -10 # diesel
*、 DC output（ V-A） ：12-8.3
*Motor type: excitation motor
*、 Machine oil consumption G/KW.H ：200
*、 working hours H ：12
*Silencing device: mute
Engine parameters
*Engine model: OU-320FTSI
*Cooling mode: water cold
*、 Rated speed r/min ：3000
*Combustion system and cylinder structure: Four cylinder V-type, direct injection engine
*Air intake mode: naturally aspirated
*Oil tank capacity: 32L
*Oil capacity: 2.8L
*、 Overload capacity % ：100
*. Speed regulation mode: mechanical speed regulation
*. Machine configuration: mark accurate
*Insulation grade: F
*Connection mode: rigid connection of taper shaft
Overall appearance and weight noise
Length: 1550mm
Width: 865mm
Height: 1100mm
Net weight of the whole machine: 530/630KG
7m/db(A)3000rpm(min-1)：59-72
Optional:
Industrial mute, remote start, adaptive plateau supercharger, ATS automatic switching device
after-sale service:
One year warranty and lifetime cost maintenance
