resin Colloidal powder What are the uses of? What is the amount added per ton?
Detailed description: bonding mortar Rubber powder consultation Today's price Bonding mortar is made by cement 、 Quartz sand The polymer binder is mixed with various additives through mechanical mixing. Mainly used for bonding Insulation board It is also called polymer insulation board bonding mortar. The bonding mortar is made of high-quality modified special cement and a variety of macromolecular materials and fillers through a unique process, with good water retention and high bonding strength. Main feature 1: It has strong bonding effect with base wall, polystyrene board and other insulation boards. 2： It has good water resistance, freeze thaw resistance and aging resistance. 3： It is convenient for construction and is a very safe and reliable bonding material for thermal insulation system. 4： No sliding and falling during construction. It has excellent weather resistance, impact resistance and crack resistance. It is mainly used for bonding polystyrene board, rock wool board, extruded board and other insulation board inner walls, outer walls and suspended ceilings. 1： Base course requirements: flat, firm, dry and clean. The new plastering layer can be constructed after hardening and drying for at least 14 days (the flatness of the base course is less than 2-5mm/m2). 2： Material preparation: add water at the proportion of 25-30% of the weight of the material (the amount of water can be adjusted according to the base course and climate conditions) until the mixture is evenly mixed. The mixture should be used up within 2 hours. 3： The amount of bonded polystyrene board is 4-5kg/m2. According to the flatness of the wall, the whole surface bonding method or the point frame method are used for bonding the polystyrene board. A: Whole surface bonding: it is applicable to the flat base course whose flatness is required to be less than 5mm/m2. Apply the adhesive on the insulation board with a serrated plasterer, and then glue the insulation board on the wall from bottom to bottom. The board surface is flat, and the board joints are pressed tightly without gaps. B: Point and frame bonding: it is applicable to uneven base course with unevenness less than 10 mm/m2. Apply the adhesive evenly to the edge of the insulation board with a plastering knife, and then evenly distribute 6 bonding points on the board surface. The coating thickness depends on the flatness of the wall. Then stick the board to the wall as above.
The ratio of bonding mortar to water is about 4:1 (weight ratio), until it is evenly mixed. Reference dosage: 4~6kg/m2 base wall must be flat, firm, clean and dry. The loose parts of the coating layer and plastering layer on the wall surface of the base course must be removed. The newly coated plastering layer must be dried and hardened before use. Use a plastering knife to plaster the adhesive paste onto the insulation board, and then evenly rub and paste the insulation board onto the base wall from bottom to bottom. The board surface should be flat, and the board joints should be compacted until there is no gap. The flatness shall be checked with a 2m guiding rule, and there shall be no adhesive between the slab joints. Pasting method: point to edge pasting or strip pasting area ≥ 40% of the whole board area. This product is packed in kraft paper bags, each with a net weight of 40kg. Stored at 5~30 ℃ for 6 months, sunscreen and waterproof, and transported as non dangerous goods. It shall be stored off the ground on the supporting plate to avoid rain wetting and ensure ventilation and dryness. Avoid direct sunlight. Note 1: After mixing the bonding mortar in the mix proportion, the viscosity of the mortar can be adjusted according to the situation of the construction site. 2： The temperature of the construction environment and the base wall shall not be lower than 5 ℃, and the wind force shall be below Grade 5 to avoid construction in rainy days. 3： When pasting the insulation board, it shall be evenly rubbed and pressed, and shall not be pounded and vibrated. 4： Within 48 hours after pasting, the construction of the next process shall not be carried out, and touch, knock and vibration shall be avoided. 5： In case of wind force above level 5 or rainfall, protective measures shall be taken. 6： The mixed mortar shall be used up within 2 hours, and the solidified and hardened mortar shall not be used again. 7： It is forbidden to add sand, cement and other additives on the construction site without permission. Bonding mortar is made of cement, quartz sand, polymer binder and various additives through mechanical mixing. The adhesive mainly used for bonding insulation board is also called polymer insulation board bonding mortar. The bonding mortar is made of high-quality modified special cement and a variety of macromolecular materials and fillers through a unique process, with good water retention and high bonding strength. Main feature 1: It has strong bonding effect with base wall, polystyrene board and other insulation boards. 2： It has good water resistance, freeze thaw resistance and aging resistance. 3： It is convenient for construction and is a very safe and reliable bonding material for thermal insulation system. 4： No sliding and falling during construction. It has excellent weather resistance, impact resistance and crack resistance.
It is mainly used for bonding polystyrene board, rock wool board, extruded board and other insulation board inner walls, outer walls and suspended ceilings. 1： Base course requirements: flat, firm, dry and clean. The new plastering layer can be constructed after hardening and drying for at least 14 days (the flatness of the base course is less than 2-5mm/m2). 2： Material preparation: add water at the proportion of 25-30% of the weight of the material (the amount of water can be adjusted according to the base course and climate conditions) until the mixture is evenly mixed. The mixture should be used up within 2 hours. 3： The amount of bonded polystyrene board is 4-5kg/m2. According to the flatness of the wall, the whole surface bonding method or the point frame method are used for bonding the polystyrene board. A: Whole surface bonding: it is applicable to the flat base course whose flatness is required to be less than 5mm/m2. Apply the adhesive on the insulation board with a serrated plasterer, and then glue the insulation board on the wall from bottom to bottom. The board surface is flat, and the board joints are pressed tightly without gaps. B: Point and frame bonding: it is applicable to uneven base course with unevenness less than 10 mm/m2. Apply the adhesive evenly to the edge of the insulation board with a plastering knife, and then evenly distribute 6 bonding points on the board surface. The coating thickness depends on the flatness of the wall. Then stick the board to the wall as above. The ratio of bonding mortar to water is about 4:1 (weight ratio), until it is evenly mixed. Reference dosage: 4~6kg/m2 base wall must be flat, firm, clean and dry. The loose parts of the coating layer and plaster layer on the wall surface of the base course must be removed. The newly coated plastering layer must be dried and hardened before use. Use a plastering knife to plaster the adhesive paste onto the insulation board, and then evenly rub and paste the insulation board onto the base wall from bottom to bottom. The board surface should be flat, and the board joints should be compacted until there is no gap. The flatness shall be checked with a 2m guiding rule, and there shall be no adhesive between the slab joints. Pasting method: point to edge pasting or strip pasting area ≥ 40% of the whole board area. This product is packed in kraft paper bags, each with a net weight of 40kg. Stored at 5~30 ℃ for 6 months, sunscreen and waterproof, and transported as non dangerous goods. It shall be stored off the ground on the supporting plate to avoid rain wetting and ensure ventilation and dryness. Avoid direct sunlight. Note 1: After mixing the bonding mortar in the mix proportion, the viscosity of the mortar can be adjusted according to the situation of the construction site. 2： The temperature of the construction environment and the base wall shall not be lower than 5 ℃, and the wind force shall be below Grade 5 to avoid construction in rainy days. 3： When pasting the insulation board, it shall be evenly rubbed and pressed, and shall not be pounded and vibrated. 4： Within 48 hours after pasting, the construction of the next process shall not be carried out, and touch, knock and vibration shall be avoided. 5： In case of wind force above level 5 or rainfall, protective measures shall be taken. 6： The mixed mortar shall be used up within 2 hours, and the solidified and hardened mortar shall not be used again. 7： It is forbidden to add sand, cement and other additives on the construction site without permission. Excellent quality is the absolute truth of the company's statement. The rubber powder with problems will never leave the factory and strictly control the quality of the company's purpose; Good user reputation, good quality, good company philosophy; Deliver the better products to the customers. The company solemnly declares: 1. Sign the product quality guarantee letter and promise that the unqualified products will never leave the factory. 2. Follow up service of product quality within two years, and keep customer service records in archives for 20 years. 3. Due to product quality problems, our company will guarantee, return and replace products to meet customer requirements.
