Multi platform CPU heat sink, pure copper material design, three 6mm heat pipes, direct contact with the CPU, more obvious heat dissipation, 9cm temperature controlled fan
It's hard to find the picture. I will tell you that you should touch the grounded metal discharge before installing it, so as not to damage the electronic devices by static electricity.The radiator of the Red Sea is very thin and easy to scratch[Detailed]
It's OK to install it like this. I also installed it like this. It has been used for nearly a year. The temperature is very stable. I installed an additional pci exhaust fan
It must be blowing to the back of the chassis. It is better to fan at the back price.Heat dissipation installation picture (click to see the larger picture)
All copper has good heat dissipation, and the fan is very quiet. I have used it for more than a year, and now I will publish it.They didn't say that the motherboard was bent. The motherboard was fixed by six screws on the chassis, and the radiator was between four screws. It would not hurt the motherboard at all. In addition, there was a backplane. In short, I used it well, very satisfied, and suitable for any chassis
Disadvantages:
The flaw in the beauty is that there are three tubes. If there are four tubes, it will be perfect
I just replaced the CPU with the Phenom II X4 945, 95W model.Use the previous Kyushu Aeolus Beta 400 to press it, and it is found that the noise of the fan is unbearable.After using the overclocking Sanhonghai Premium Edition, the CPU temperature was well suppressed at about 50 degrees, and the fan sound was very, very low, which was very good.As far as materials are concerned, they are all copper materials, and their thermal conductivity must be higher than that of aluminum.The fan is fixed with good soft nails. It is firmly fixed, and there is basically no noise. It is very cool.
Disadvantages:
Although it can hold my 945 under normal circumstances, once the CPU runs with full load, such as running minutes, the temperature rises rapidly.After opening the chassis and studying it, a problem was found.When the CPU temperature is very high, the base of the heat sink becomes very hot, but the temperature of the heat sink above is not very high;Especially the top one, the temperature is almost the same as the room temperature.In this way, the wind from the fan passes through the radiator, and the heat carried away is very limited.The reason for this problem is either that the heat conduction effect of the three heat pipes is not good, or that the contact area between the heat pipe and the upper fin is too small to transfer the heat of the heat pipe to the fin.After a long time, it will be found that all the heat sinks above are locally heated, that is, the places next to the heat pipe will become very hot, while the temperature of the rest is not high.
Summary:
Generally speaking, this is a superior heat sink, but I think it still needs some changes to deal with the CPU with high heat production.First, replace with better silicone grease, such as A2, to speed up the heat transfer from the CPU surface to the radiator base (pay attention to uniform and not too thick silicone grease, just fill the air on the contact surface between the radiator base and the CPU);The second is to add a fan to the radiator, and use two fans to blow and suck one to accelerate the local heat dissipation on the radiator, so as to achieve better heat dissipation effect.
The boss said to set up a machine. After reading this on the Internet, he felt that it was OK. Referring to the price, the boss bought it back.The advantage is that it looks very scary. It has a large radiator and a large air volume.Just these two. Large heat sink and high air volume. The new machine is not equipped with anything. I feel the temperature is OK, and it is stable at 24 degrees.And the room temperature is not high, that is, more than ten degrees.
Disadvantages:
The biggest defect is installation!!I have installed the most laborious cooling fan, using ASUS P8Z77-V LX motherboard, I3-3220CPU,Two bases, the smaller one, but it was very hard to cover one side and press the other side, which failed many times. My colleagues and I dared not press because we felt that the board was deformed several times, because the force was too big. It was about 8MM away from the other bayonet, so the board was deformed and squeaked when pressed. My hand joints were cut three places by the net above the I/O port of the chassis!At last, the colleague was cruel and succeeded.Other disadvantages are hard to say. The muted version feels that the muted effect is average, not as good as expected. If the room is quiet, you can hear the sound of the fan. Then there is some doubt about the heat dissipation performance of the side blowing. The thick base is connected to the layers of chips above, and the fan cannot be adjusted.
Summary:
If it is similar to my motherboard and CPU, I will change it. It is really hard to install, and I dare not think about taking it off.