To Rui Wrath Ship DX7

The design does not need screws. The four doors are easy to assemble and disassemble. The appearance is good and the price is affordable

The space for the back line is too small and there are few holes on the back, so the original long line and hard line can't be used. The integrated water-cooled line of 240mm and above should not be considered. If it is put in, it will block the memory and it is troublesome to disassemble and assemble. The keys have collapsed, the panel slot has collapsed, and the side mounted LED can easily block the optical drive

High end players don't need to consider this chassis. Ordinary players can consider it if they want to save money and go to the whole tower

The full tower has enough space to install a lot of things, and there are two non removable hard disk bits, which actually eliminates the need for plug-in cables Back space is OK It is possible to install 8 fans and 2 light strips. There are indeed many accessories. There is an LED fan control on the upper part, but only 3 fans can be controlled. The number of three gears of the hub has not been tested

Although the back space is large, the location is unreasonable, and the CPU power supply cannot be passed through the back cable There are enough fan positions but no dust-proof measures. The three fans are all big holes. Don't tell me about dust-proof measures. And the button part has collapsed after two or three months of use, and the fan speed is not adjusted to the maximum when there is a current sound. I don't know why I feel very sad that there is no dust-proof net. Except for the power supply, there is a plastic film attached to the factory. It says that no fan should be installed. Don't tear the 500 chassis. There are too few details There is also the side transparent and flush one, but it has to be said that it is too small and the color of the board itself is too dark. The eight LED fans can't feel it! Can't feel the brightness

The chassis side view and fan are the highlights and weaknesses

Only large space and many slots, others... I don't know what my friends think about buying the whole tower at this price...

1. In terms of workmanship, because it is cheap, there are many quality control problems. The right leg of the chassis head is crooked, and the same problem still exists after a friend changes the goods. The hard disk bracket is skewed. Rubber walking holes and water-cooling holes are easy to fall off. 2. There are many problems in the design. First, the CPU power supply position does not provide a wiring hole position, which can only be accessed from the hole position on the upper right side of the motherboard. Second, because LED light strips are laid in the middle of the front and rear parts of the chassis, and the side plates are designed to separate the front and rear, the hard disk bit wiring needs to cross the chassis bottom, and the official light strips are short, which cannot cover the entire light strip slot. Third, the SSD bit is located next to the optical drive bit, and the hard disk power supply line is easily not long enough. The mechanical hard disk bit and SSD bit need to pull two power supply lines to install normally, otherwise the length is not enough, and the SSD is installed with the back facing outward, resulting in the SATA line snap in the internal test, which is troublesome to disassemble and assemble. The lowest mechanical hard disk bit is close to the hard disk slot, and the hard disk power supply line may not be bent, resulting in installation failure. Fourth, the tool free design is not comprehensive. Although the front and side panels on both sides of the chassis support tool free, it is extremely difficult to manually tighten them. The PCI slot screws cannot be tool free. Fifth, the fan hub is located at the power key of the chassis. If the fan cable is not long enough, it will be a tragedy. Sixth, the front baffle of the optical drive bit will fall off as soon as you touch it. Seventh, I forced the cover when the space for backplane wiring was tight. Eighth, it would be better if the power supply bit had a baffle. 3. When a friend bought the fan in Tmall store, he needed to install the fan on his own, and there was no expansion screw or long strip screw of the fan. He only gave ordinary screws, and the fan mounting port had no thread. The seller said that he would directly use the screw to make the screw port. I was also convinced that the fan could kill people.