Standard version of blade 1

The appearance is very beautiful, which makes me feel like seeing the Terminator T800. 5 fans (4 fans are turned off without playing games), the air volume is good. Independent fan control The workmanship is also good, which is almost the same as the brand chassis.

Five 12cm fans need to be purchased by yourself. The hard disk power cord, we recommend that you buy an elbow. I didn't connect the hard disk power cord properly due to the back cord, so I burned one. The space on the back panel is a little narrow, and wiring is troublesome. The chassis is slightly larger and heavier. (Sisters think twice)

200 pieces for one chassis, plus 5 12cm fans (20 pieces x 5=100 pieces), about 300 pieces for one chassis The two fans above should be equipped with dust-proof screens. If you buy a fan, you can get a free one. It's not expensive to buy it. It's 1-2 yuan.

I am used to seeing the black chassis every day. My family wanted to get a white or blue one. I originally wanted to get a white version of the Rui A5, but I couldn't get it. As the second choice, I went to the Blade 1 luxury version of this snow suit. Advantages: 1. The appearance is handsome, which is the reason for choosing. 2. The price is relatively cheap, which may cause criticism. However, through visual inspection, the price of chassis with risk control, side penetration, and hot plug hard disk interface is obviously relatively cheap. 3. It is relatively easy to install the fan. The upper cover can be opened directly. The front panel can also take out the dust screen to install the fan and then insert it into many cases. When installing the fan, it is difficult. One by one, you will understand the pain of installing the fan every day. 4. Three solid state drive brackets, a real blockhouse, are very practical. 5. Don't mention the advantages that everyone has

Let's focus on the disadvantages. After all, there are dozens of them installed. I know this chassis very well. If you don't know this chassis, you can leave a message below me. 1. The evil back wiring is really a trick. After walking to Rui A5, which has a perfect wiring of inverted 360, comparing with the few blades in this hole, it is really a test of technology. The space on the back is small, and there are very few places to tie the wire. There is only one channel to tie the wire. If you don't tie the wire, it will be scattered into a pile, which is very ugly. All the wires are tied into the single channel, which is too crowded. This is really tangled. It is necessary to try several times, lay the line horizontally, and use all the non binding holes nearby to tie the line, so as to perfectly cover and route the line. 2. In fact, the workmanship is very ordinary. After all, the iron plate is thin and easy to lose paint. The white side transparent plate is not transparent at all. (Later, the Blizzard version should correct this problem.). 4. The risk control actually said that the chicken ribs are also a big chicken ribs. Anyway, since I installed them, I have never adjusted them and it is still troublesome to install the fan risk control. There is no manual, so I spent half an hour installing and studying them for the first time. 5. The width of the cabinet is a little narrow, and the high fans are just easy to put on. 6. The lighting effect is not good. I have installed all five fans, but they are not half as bright as the renderings, A little disappointed

Since it is so popular, naturally it has its selling point. After all, there is no perfect case. Overall, I feel it's OK to use it, and I can afford the price. Many people say that the lack of dust screen on the top is a disadvantage, and they disagree with this point. The top fan originally blows outward, so the outward direction naturally does not need the dust screen, otherwise the wind force will be affected. The dust screen is installed on the front panel for ventilation, and the dust screen is not installed on the upper panel for ventilation. This design is reasonable

As long as 199, the high tower chassis is designed with thick steel plates, and the layered design of the front panel mesh structure is conducive to heat dissipation. The design interface of the front panel is complete, as well as the fan regulator. The internal structure is also sufficient, and the materials used are very conscientious.

The mesh structure may be easy to enter dust, and should not be used in dusty environment.

The price of 199, the high tower design, and the rich interfaces are not bad.