Comments on Jiuzhou Fengshen Dark Ice 300

The heat dissipation effect is good. The dark blade shooter version used to press i5-4570 and stand by 40 degrees, but it can reach 90 degrees with full load. Now it has replaced the dark ice 300, stood by 25 degrees, and capped with 55 degrees with full load. The noise is low. The fan changes speed intelligently. From 900 RPM to 1300 RPM, I don't feel the noise becomes louder.

It is not convenient to install, the buckle is very tight, and when pressed down, the motherboard is about to break... I plan to replace the E3 1230 V3 recently, and it is not convenient to remove it visually. The price is on the high side. The price of black ice 200 is 40, the price of black ice 300 is 80, and the price of black ice 400 is 100. According to the number of heat pipes, the middle number of 40 and 100 is 70!

Overall, the effect is good, and the price is on the high side.

The motherboard uses P8B75-V, which I use to press the i53470. The sound can be heard only when the ear is attached to the chassis. After playing for three hours, the sword mesh III has a room temperature of 25 degrees, and the CPU temperature is within 40 degrees. It is the best heat sink I have ever used, and it was brought with me before. Some friends said it was not easy to install, but I installed it in three minutes according to the instructions, and there was no problem that other netizens said the fasteners were too tight.

It took a week, but I haven't found it yet.

Large fan, good temperature control, low noise, good choice.

Intelligent temperature control. My A8-3970 has a power of 117 watts, a room temperature of 24 degrees, a standby temperature of 37 degrees, and a game temperature of no more than 50 degrees. The revolution has barely reached 1000. I'm very satisfied~

I haven't found it yet. For children's shoes whose speed cannot be adjusted, you need to go to the smart fan item in the bios to adjust the fan control to active control and 4pin or pwm, which is good~~

Taobao 85 yuan package was mailed, and the radiator was covered with silicone grease, but it is not recommended to use the original factory coating. It is dry and may be scratched during transportation. It is recommended that you go to the Science and Technology City or directly buy high-quality silicone grease online. After applying it, you must scrape it thin. The silicone grease of the overclock III is directly equipped with a scraper. If there is no scraper, I can make it by myself. I cut it by myself using the plastic outer package that contains the memory of the pirate ship. The best effect is to scrape a thin layer, which can completely cover the bottom. Too much or too little is not enough.

4 The heat pipe is very powerful. The AMD platform does not need to remove the main board to achieve side blowing. The heat dissipation effect is good. The room temperature is 26 degrees. The X4 955 does not overclock and stands by 37 degrees. The full load is 50 degrees. It should be completely able to withstand a small overcharge (my chassis is first assassin 1, and fans are installed on the front and back). The noise is not wrong. Personally, I think it is very low

The fastener design is very poor. It is not a downforce type, but a downforce type. If the screw slips, it will be scrapped, which makes people feel insecure. The fastening screw provided is also very short, not beyond the top of the screw hole. I don't understand why the screw is so short since the design is a downforce type fixation

It is suitable for entry-level users to choose, but the thickness of the chassis must be measured before, and there must be more than 160mm space from the CPU to the side cover

I'm using it. The workmanship is excellent. Please pay attention to the size of the case when buying this heat sink. Generally, the case can't be plugged. I won't overclock. I'm a bit rich when buying this. The AMD six core is in standby at 31 ℃, and the room temperature is about 18 ℃.

It is not easy to install the fan. The fan is very large. It is a little loose after being stuck on. The pad with it is not easy to pad the fan. You have to check the position in advance.

The operation is very quiet, and the temperature has also dropped, which is good.

I bought a 12cm fan separately, and two fans can be installed at the front and back, and the heat dissipation effect is better. The four tube heat dissipation is not the same product, and the heat dissipation effect is very good. I used the i5 2320, with the P67 motherboard, and the hidden four times full frequency open 3.7G. The room temperature is 16 degrees, the boot temperature is 37 degrees stable, and the full load is 62 degrees - 65 degrees, which is not bad.

The height is too large. Generally, the chassis is only 14CM-18CM wide. The fan is about 16cm high. It is difficult to install a small chassis.
Secondly, the upper part of the fan is larger than the lower part which contacts the CPU. When installing the fastener, the main board can only be removed before it is buckled. It will be very inconvenient to replace the original fan.

Generally speaking, the air volume is good, and the heat dissipation effect is good. However, the installation of fans is troublesome, especially the replacement of fans. The height is high, and the workmanship is slightly rough. There is no overclocking or cool cooling similar products that look fine.

Tower type, three heat pipes, 4-wire speed regulating fan, mute.

The boat type fastener is too tight, and it can only be installed with force. After installation, it is necessary to adjust whether the radiator contact surface covers the CPU. The strength of the fixing screws of the original ship type fastener is insufficient, and a slight force may cause the screw torx to be flattened.

Tower type three heat pipe, fan supports 4-wire speed regulation, standby speed is about 1000, room temperature is 27 degrees, CPU temperature is about 37, silent. The silicone grease in the original package has been coated on the radiator, saving the trouble of coating it again. Some people say that the silicone grease in the original package is relatively dry. I think it may be a problem during transportation. I started with it fairly well. The screw of boat type fastener is not strong enough, and the plum blossom of cross screw will be smoothed with a little force.. (I overexerted one of them, and the plum blossom was smoothed... embarrassed.)
In a word, this is a good thing. Although there are some problems that are not problems, it is also related to everyone's installation methods and habits. The price is fairly good, and it is worth it.

Quiet, good temperature control

There are no shortcomings for the time being. Note that after the installation, the radiator base should be pushed to the center of the CPU. Don't mention that the cover is incomplete

The 955 processor I use does not overclock. The Z9 silica gel black ice 300 can hold my 955 at room temperature 28, standby at about 40 degrees, rotating speed at 1100-1200. When the game is running, the rotating speed is above 80%, the room temperature 28 degrees, and the CPU temperature remains at 50 degrees. If it is good to choose overclocking, I will probably choose black ice 400

My u is a pterosaur quad core 955, equipped with a black ice 300. I mainly play stand-alone games. I don't know much about computers, and I can't measure the temperature. However, I feel really good when I use it myself. I touch the chassis, and basically can't feel the temperature. Maybe it is my good personality. The sound I use is also very low. I upgraded from the Velociraptor dual core 250 to the pterosaur 955, so it is very convenient to install it. But it is really big, twice the heat dissipation of the original AMD. My chassis is Onda VX100+, equipped with black ice 300, and barely closed the cover. This is my chassis size 445212450mm, for your reference.

I haven't found it yet

To be honest, this is my first time to distribute products. My culture is not high and my expression ability is limited. I just want to provide some reference for friends who buy heat dissipation products. Overall, it's really good. If the full score is 10, I'll give it 9.5

The package is simple, the main body is small, and three heat pipes are enough.

The installation is not so simple, one screw cannot be screwed in, and the instructions are relatively simple, but it is easy to install it by experienced people. Test your practical ability.

It's not big enough to fit into a smaller case. I ordered a black ice 400, but found it couldn't fit, so I replaced it with a black ice 300. If the cnq is not turned on, at full speed of 1600+rpm, there is noise, but it is acceptable, and the temperature suppression is also good - the silicone grease used is the leftover from the video card radiator I bought a few years ago. It's better to open cnq. Temperature control is worth hundreds of yuan.

After all, it is an entry-level radiator and a three tube tower. The overall workmanship is satisfactory. The 5800K does not overclock or has a good effect. The A85X motherboard enables temperature control and noise control. It has tried 4.2GHz and 2000MHz memory frequencies and is fully silent. Not bad. After 95 and a half hours of Prim,

After testing the memory frequency of 4.5GHz and 2133MHz, the temperature is a little high and the noise is rising.

The entry-level mini tower supports temperature control and has good household effects.

I used it on the AMD FM1 platform to suppress 3870K. The radiator is compatible with the surrounding of the platform.
The simple shape and transparent fins of this radiator enable it to make more effective use of the airflow from the fan. The delicate fins and FIN technology also ensure the firmness of the product in structure. Although CTT technology may be disliked by some netizens, the final performance obtained is commendable. In terms of fans, the black translucent LED blue light Aeolus of Ice Edge has a good reputation. Personally, it would be better if it were replaced with double ball bearings.

It is troublesome to install. You have to remove the main board. It takes considerable force to buckle the fasteners.

In actual use, the radiator of CTT technology has a better cooling effect when the fan is running at a constant speed than when the speed is changing.
Ladies and gentlemen, as long as your chassis can be installed properly, it is worth considering. It has a good cost performance ratio. I'm going to replace my Intel platform with another one.

The previous pressure was 5800K, and the standby temperature was less than 30 degrees. This time it was 3470 degrees, and the standby temperature was also about 30 degrees. I had heard that the third generation of Core was not able to heat up. This temperature was satisfied. Three heat pipes were enough, and they were not as big as the black ice 400. Almost all the middle tower models could be put down, and the automatic speed control was basically maintained at about 900 rpm. Almost no sound could be heard. The heat pipe was in direct contact with the CPU, which was perfect.

There is still noise when running under full load. The fasteners are not very easy to install.

I have no other requirements for the radiator, as long as it can cool down and be quiet.

Amd 965 The original fan can't stand the noise of the original 635 fan. The noise of the original 635 fan can't stand the temperature. The standby temperature is more than 60 degrees. The 400 heads that were supposed to be on the black ice 400 are too big. The chassis is too big. Just X east activity 69 starts with the black ice 300, standby 45, full load 57, not overclocking enough

The fastener is a little wasteful, and the heat pipe is factory felt. It has advantages and disadvantages, and it is also convenient

69 It's worth it

The workmanship is good. The base and the motherboard are well combined, very firm, and the heat dissipation is also very good. My original Q8200 radiator needs more than 40 seconds in standby. After installing this, it has an immediate effect, reducing about 10 degrees.

The fastener is not easy to install, and it is difficult to fix the buckle.

When installing, please be sure to know the layout of the components on your motherboard. For example, my motherboard Gigabyte P43 needs to rotate the fan base before installing. Otherwise, the two buckles will be blocked by the North Bridge chip heat sink. Finally, it needs a little skill to press the buckles. Be bold and careful.

E3 1230 V2 standby 30, full load 55, room temperature 19 degrees, with one chassis fan turned on, in summer, all chassis fans turned on and then well coated with silicone grease, the full load should be below 60. Very good. Installation is very simple.

It conflicts with the side panel fan of the white version of Warcraft V8, so the fan of the side panel of the chassis has to be replaced elsewhere. However, this is the reason for the chassis, not the reason for the radiator. I like the large radiator. It looks comfortable.

It is an excellent choice for matching E3 1230 V2. Low is not enough, high waste.

I bought it in Zhengzhou 90, AM3 255 u, and the original radiator stood by 42 degrees after 800 revolutions. When I installed this 800 revolutions stand by 32 degrees, the heat dissipation is very good, the materials are solid, the workmanship is good, and the sound is quiet.

The reserved holes of the base screws were not tapped, which made it difficult to install. Three of the screws were directly damaged. I went to buy a 3mm tap and four sets of 3mm long screws. After tapping, I tightened the screws and added more nuts than the original ones. I don't worry about the screws coming loose any more. It's a once and for all!

The overall cost performance ratio is good, and installation requires a certain amount of hands-on ability.

I want to build a cheap small game console when I install it, so I don't plan to invest too much on the platform. I think I have some experience in online shopping, so I bought a 6-core 640T and a 880GZ board from Yingtai. It is said that I can open the core with one click. It's OK to try it. Another ASUS GTX650 was found on the forum. Only the new one was bought by Xuanbing 300. After a simple test, the installation was very successful. The one button nuclear opening was normal. The heat dissipation efficiency of the S300 was also very strong. The noise of turning on the temperature control and LOL fan was basically within the acceptable range.

When the CPU copy is done separately, the fan will work fully, and the noise is obvious

Low cost performance, high heat dissipation efficiency

Good workmanship, good heat dissipation, quiet, moderate weight.

It is recommended to take the motherboard out of the chassis during installation, otherwise it is difficult to install. The installation is very fast, and it is very suitable for AMD U's.

A8-3870 processor, ASUS F175PRO motherboard. After replacing this U, ASUS has its own temperature control display U temperature 33, which is 10 degrees less than AMD's own heat dissipation. There is no warning of exceeding 60 when running minutes, and the maximum display temperature is 46 Very quiet. In the dead of night, I only heard the sound of the chassis fan and the hard disk reading. I was very satisfied.

Today, I just bought Gigabyte GA870A UD3 VS AMD955. It is said that AMD has a huge heat, so I spent 100 dollars to buy this radiator. The AMD 955 exceeds 3.5 standby temperature by 30 degrees, and the AID64 reproduces the machine for 30 minutes by a maximum of 51 degrees, which makes the temperature lower than my 3770. The average temperature of the SF3 wind freeze S126 used in the 3770K is about 5 degrees higher than this. I really think it's good to change to Z77 MPOWER one day! We strongly recommend you to buy

Among the 100 yuan, the price performance ratio is the highest. As for the appearance, it is average. After all, every price is worth every product. If you add a fan, it will be perfect. Hehe

Great, you deserve it! Due to the stability of the test, the board is still on the outside. The pictures will not be uploaded, but will be loaded into the chassis first