The Blizzard T824 air-cooled radiator produced by Kuleng Zhizun is probably the top product of the current air-cooled radiator. It is a double tower structure, equipped with 8 superconducting composite heat pipes, with a fully wrapped copper bottom, and supported by two Mobius fans, it can cope with CPU power consumption up to TDP300W, which is rare in the current air-cooled radiator,The heat sink adopts a rise and fall design for the memory part, which has better compatibility. Of course, the compatibility of mainstream dual platforms can't be said, and the combination with Kuleng's own chassis will complement each other.
Previously, I used the Asaxin 4 from Kyushu to replace the z690 for snow blowing, so I bought this one. It was perfectly installed, and the effect was OK. It's just that this radiator is designed a little strange. It's difficult to remove the middle fan and change the direction. It's totally not from the perspective of DIY players. The external fan can only be installed on one side, because only one side has an installation slot. This is a bad comment,There is no freedom at all. It's OK on the whole. It solves my needs
599 The price is still worth it!I press 7950x to do 3D rendering, long-term overclocking and full load!For the same 90 ° temperature wall, the frequency reduction of air cooling is not more than 0.05Ghz than that of vk 360 water cooling!But the noise really dropped too much, and the water cooling noise made me dizzy!I felt it was very good!It's worth recommending!
There is no problem with the packaging. The opening is defective. It is estimated that the heat sink at the bottom has shifted, and the metal color of the heat pipe has leaked out.The biggest problem is that there is a tolerance. Well, there is a tolerance of about 1.5mm between the bases. As a result, the normal installation screws cannot be screwed on, and it is unavoidable to pad up some of the shims to reach.After installation, the effect is good, and I can tolerate it.
Heat dissipation effect: the standard is 300 for heat dissipation. In fact, it is OK. After all, there are so many copper tubes, but the volume is too large. My chassis is already a server level large chassis, and I feel that the heat dissipation is large????Don't worry about the general chassis. It should be the one in Shangjiuzhou
The appearance is very handsome, and the heat dissipation effect is also very good. The only bad thing is that the buckle of the fan outside is not too tight. There is nothing wrong with other things.
After two sets of 420 water cooling were tried and hamburgers were sandwiched, 7800X3D was pressed to about 70. This air cooling was no worse than 420. Two LCD fans were replaced. The road water cooling was the same, and the real-time temperature could be seen.The cost is more expensive than 420 water-cooling, which is the most expensive of a ship, but it is safe and not afraid of the risk of leakage.
Previously, I couldn't hold 13900k with d15s, so I bought this 8 heat pipe to try. I set a temperature wall of 80 degrees, and the room temperature was 24 degrees. However, the CPU can only reach about 4.6-4.8G when it is fully loaded
It's a mess. What kind of product design? The external fan is not firmly fixed at all, so the mobile chassis falls off. I don't know how to design the snap.
The appearance is domineering. I didn't choose * * *. It was evaluated that the removal of a fan would not affect the heat dissipation efficiency. It is friendly to the memory. The last one I used was Cooma's gtv8, a soaking plate. This one was downgraded without it. It is still quiet. The price is not cheap in air cooling. I can buy a good water cooling at the same price. The main reason is that I can't trust water cooling. I am lazy,Cool air can save you worry.
It's very big. I bought this super large case. It said that the cooling function is very good. It was just assembled and used for a while. There is no noise. It's not bad!It seems that it is OK, but it would be better if the price was lower.
