Comments on Overfrequency Three Red Sea Standard HP-928

All copper has good heat dissipation, and the fan is very quiet. I have used it for more than a year, and now I will publish it. They didn't say that the motherboard was bent. The motherboard was fixed by six screws on the chassis, and the radiator was between four screws. It would not hurt the motherboard at all. In addition, there was a backplane. In short, I used it well, very satisfied, and suitable for any chassis

The flaw in the beauty is that there are three tubes. If there are four tubes, it will be perfect

It's worth it

I just replaced the CPU with the Phenom II X4 945, 95W model. Use the previous Kyushu Aeolus Beta 400 to press it, and it is found that the noise of the fan is unbearable. After using the overclocking Sanhonghai Premium Edition, the CPU temperature was well suppressed at about 50 degrees, and the fan sound was very, very low, which was very good.
As far as materials are concerned, they are all copper materials, and their thermal conductivity must be higher than that of aluminum. The fan is fixed with good soft nails. It is firmly fixed, and there is basically no noise. It is very cool.

Although it can hold my 945 under normal circumstances, once the CPU runs with full load, such as running minutes, the temperature rises rapidly. After opening the chassis and studying it, a problem was found. When the CPU temperature is very high, the base of the heat sink becomes very hot, but the temperature of the heat sink above is not very high; Especially the top one, the temperature is almost the same as the room temperature. In this way, the wind from the fan passes through the radiator, and the heat carried away is very limited. The reason for this problem is either that the heat conduction effect of the three heat pipes is not good, or that the contact area between the heat pipe and the upper fin is too small to transfer the heat of the heat pipe to the fin.
After a long time, it will be found that all the heat sinks above are locally heated, that is, the places next to the heat pipe will become very hot, while the temperature of the rest is not high.

Generally speaking, this is a superior heat sink, but I think it still needs some changes to deal with the CPU with high heat production. First, replace with better silicone grease, such as A2, to speed up the heat transfer from the CPU surface to the radiator base (pay attention to uniform and not too thick silicone grease, just fill the air on the contact surface between the radiator base and the CPU); The second is to add a fan to the radiator, and use two fans to blow and suck one to accelerate the local heat dissipation on the radiator, so as to achieve better heat dissipation effect.

The boss said to set up a machine. After reading this on the Internet, he felt that it was OK. Referring to the price, the boss bought it back.
The advantage is that it looks very scary. It has a large radiator and a large air volume. Just these two. Large heat sink and high air volume. The new machine is not equipped with anything. I feel the temperature is OK, and it is stable at 24 degrees. And the room temperature is not high, that is, more than ten degrees.

The biggest defect is installation!! I have installed the most laborious cooling fan, using ASUS P8Z77-V LX motherboard, I3-3220CPU, Two bases, the smaller one, but it was very hard to cover one side and press the other side, which failed many times. My colleagues and I dared not press because we felt that the board was deformed several times, because the force was too big. It was about 8MM away from the other bayonet, so the board was deformed and squeaked when pressed. My hand joints were cut three places by the net above the I/O port of the chassis! At last, the colleague was cruel and succeeded. Other disadvantages are hard to say. The muted version feels that the muted effect is average, not as good as expected. If the room is quiet, you can hear the sound of the fan. Then there is some doubt about the heat dissipation performance of the side blowing. The thick base is connected to the layers of chips above, and the fan cannot be adjusted.

If it is similar to my motherboard and CPU, I will change it. It is really hard to install, and I dare not think about taking it off.

1. The white and transparent hydraulic bearing fan is beautiful and quiet.
2. Use all copper heat sink to improve heat dissipation speed.
3. Connect the fan with rubber to reduce the noise of the fan

1. The weight is a little heavy, which is easy to deform the main board. It is better to use the CPU anti deformation strip iron sheet and fan bracket on the back of the main board to ensure that the main board is not deformed.
2. There is a problem with the automatic speed control function of the fan

In general, this fan is worth buying, but it is better to use it on high-end mainboards because there is no CPU anti deformation piece on the back of low-end mainboards, which is prone to deformation

Polish the base, the heat dissipation is very good, and it is better to use two fans

The heat sink should be put on the hand sleeve, otherwise it will be ugly after rust, the weight is OK, not like most people said that the buckle will be black after a period of time, the appearance is a little ugly, the heat sink is too thin, affecting the heat dissipation, and the heat pipes are distributed on both sides, affecting the heat pipe to heat the heat sink.

It's worth more than 100 yuan, but it needs to be reformed to give full play to the best effect

1. Copper aluminum combination, FIN process, heat pipe direct contact, these technologies are applied well
2. Large heat dissipation area, light weight, no need to worry about main board deformation
3. All platform compatible, easy to install, applicable to all platform entry-level tower radiator
4. It is suitable for CPU with power consumption of about 65 watts, full load heat dissipation without pressure
5. Fan air volume is enough

1. There are only two copper tubes, a little less. The cooling tower has no nickel plating process, so the heat dissipation effect is average, and the CPU with high power consumption cannot be pressed under full load
2. The fan is noisy. Sorry for the name of the silent version
3. The fastener is a little tight, and beginners need to work hard, but it is easy to install it if there are too many fasteners
4. The workmanship is slightly rough, with fast heat absorption and slow heat dissipation, which makes the CPU temperature very unstable. When executing large programs, the temperature fluctuation at 30 degrees is normal, but the temperature returns quickly

Affordable to this price, competitive at the same price. The problem is that the aluminum sheet has less specific heat. The temperature rises too fast and falls faster. It would be perfect if it could be improved

The bottom layer of all copper seems not to be very attractive. It is the only radiator with a relatively low and narrow chassis. It is a good choice for players with a chassis width of no more than 19. The 89W U used to buy a 50 yuan radiator. In summer, when it was 36 degrees Celsius, the format factory was open and the temperature rose 100% gradually until 100 degrees Celsius automatically shut down. After this installation, the CPU was turned on at 32 degrees Celsius, 100 hours and 52 degrees Celsius
I have never tried overclocking. I dare not talk about the installation. It is not hard to imagine. Generally, people with a little manual ability can do it for as long as a special screwdriver for a magnet. It costs 3 yuan. I bought a hardware store. The four corners are spiral springs that can automatically adjust the tightness. It is best to rotate until you feel that it is very difficult to stop screwing. Don't kill yourself. The screwing has its own heat conduction Very garbage. Although it's really dry, it's OK to use a knife to scrape a little on it, because more will definitely be squeezed out to get to both sides of the CPU. Is it heavy enough that others say that chopsticks should be used to support the god horse? As long as the 2-3 screws on the top of the motherboard are tightened, there is no problem. Recently, it may be changed to a game, the fierce V8, and then try the temperature. Of course, the radiator is better The temperature also has a lot to do with the chassis

I feel that there are a little few tubes. If there are four tubes, it will be perfect. The number of buyers is absolutely too many. I don't know whether there are too few tubes or what kind of radiator tube. When the temperature is 38 degrees in summer, I haven't seen it too hot. At most, it is stable. 20-30 degrees? My main board BOSS does not seem to control the speed of the main board. There are four pins whose rotational speed is always around 2000. The noise is not small and the sound is not quiet. I don't know whether it is a problem with the soft pin design or what, but if the rotational speed is 900, there must be no sound

Lafeng is relatively small. Temperature control is good. Try to buy a 147cm high 12cm high fan radiator. No overclocking. This is enough. If it is small, it should also be a problem. It is worth recommending

Taobao bought it for 55 yuan, which was not bad. It was about 40 degrees when it was fully loaded, not more than 45 degrees after overclocking, and the room temperature was 20 degrees. It's still quiet, much better than my previous one.

This is the first time to install such a troublesome AMD fastener. AMD doesn't support side blowing, which makes my top perforated fan cool

Not bad, it's worth it.

The heat dissipation is pretty good. The CPU 4000 of the host computer equipped in 2005 has been under pressure for five years with the original fan. The temperature rises to 100 when you enter the BIOS. As some people say, you can boil eggs. I originally wanted to buy a Beta 400, but there is no such advanced thing in a small place. Wandering in the Electronic City, I suddenly saw a copper tube radiator in an inconspicuous corner. The boss didn't bargain for 75 yuan, hesitated for a turn and then came back to buy it. After going back and installing, the boot temperature is 39 degrees. After playing for a while, the temperature is controlled around 50 degrees, which is still good! Play Call of Duty 6 for a day.

It's just that the vibration is a little high, and the side of the chassis is quite good!

Good temperature control

The heat dissipation effect is pretty good, 965 super 4G is barely enough.
But I give you a piece of advice, that is, the motherboard screws must be good, and it is better to use something to hang the heat sink. The pig motherboard I use is ASUS M5A97pro. Because the screws on the motherboard were not properly tightened and the radiator was not lifted, the motherboard burned a component (according to the manufacturer) due to deformation, but I was not asked to pay after it was repaired.

The radiator is too heavy. You must lift something to reduce the burden on the motherboard. The screws need not be screwed too far. It's OK to change the balance and feel tight. After a period of time, if you are afraid that the heat transfer paste will become loose due to paving, you can screw it again.

The heat dissipation is OK.

The heat dissipation is good (resulting in heavy weight), and my AMDCPU is not more than 52 degrees when fully loaded; The noise is low, and it can't be heard in the dead of night. The sound of the power fan is covered (the sound of the power fan is not loud); It looks beautiful and magnificent, but it is installed in the case.

It's too hard to pretend! Especially for AMD motherboard, the big nut with spring should be tightened but blocked by the heat sink. If it is not tightened, there will be no heat dissipation effect; The four corners of the radiator are also sharp and easy to cut hands. Also, the weight is too heavy.

Users of AMD motherboards are not recommended to purchase and use them. In addition, we should try to lift it, that is, use the power supply or the top of the chassis to share most of the weight.

1. Excellent heat dissipation effect (under ORTHOS one hour copying, the CPU temperature is still stable below 60 degrees, the room temperature is about 27 degrees, and the side panel of the chassis is not opened);
2. The mute control is very good;
3. The fan adopts bolt type, which is easier to install than screw installation (although it is a double-edged knife, it is generally better than screw installation).

1. The extremely evil installation hook (it is also difficult to install without knowing the method, and if you don't know the method, you will be crazy to say that it is a rather failed fastener design);
2. What fan is not 4-pin;
3. The installation direction is not clear. It is obvious that the two directions are not the same, except for double fans. This is a reminder to those AMD children's shoes who don't understand that the fan is said to be in the direction of the graphics card, that is, downward, not upward in the Internet. It should be said that the air duct is blowing upward and discharged through the air outlet under the power supply.

The heat dissipation and mute indicators are very prominent, and the installation mode is very confusing.

The AMD3800+of the old machine has been cool for more than three years. Today, it just retired honorably and replaced with the Red Sea MINI. The same game runs up and down from 48C to 66C. After the Red Sea MINI, it is between 31C and 44C. The heat dissipation performance is quite good and the noise can be ignored. It is very valuable for the radiator at this price. The overclock III is still trustworthy.

The fastener is too tight, so is the standard version of Red Sea. It takes a lot of effort to take it down after going up. The other thing is that this speed is a bit confusing. The introduction said that the maximum fan speed is 2200 rpm. Why is the speed of the AMD3800+always between 4400 rpm and 4500 rpm? I wonder if there is any expert who can give me some advice.

The heat dissipation of the super value CPU at the price of 50 yuan is very good.

P8B75+E3 1230 V2+ASUS GTX650TIB+blade (5 fans), this board seems to block the memory at the horizontal side, so it can only draw air from the bottom of the graphics card. The room temperature is generally between 25 and 33 degrees, and the rotating speed seems to be 2200-2500 before the outdoor (shady, slightly cool) toaster, with the maximum temperature of 56 degrees. It is estimated that the indoor limit temperature (you can stay)+deep roaster should not exceed 70, of course, the chassis fan must be turned on. The noise is also pretty good. This effect is enough. We don't plan to add fans.

The fasteners, even the screws, are saved. There are four plastic snap screws, which look a little hanging. It was very hard to install. I thought the CPU was not installed properly. Only two or three days later, I saw that the snap ring had been seriously deformed. I don't know if I will suddenly fall down

Good cost performance, very good performance, should be the best in the crosswind. If we can fix the screws and add a base plate behind the main board, the ferrule will be more solid and perfect.

Starting from No. 170 on 7.2, it is not difficult to install the Intel motherboard, and it will be done in 15 minutes.
Actual measurement: The room was sunny in the afternoon, and the room temperature was estimated to be 30 degrees. It was hot, but the radiator performed very well. The I5 OC 3.6 fan speed was 1800, and the temperature was controlled at about 39-42. Very good.

The current sound is a common problem. When I turn on the air conditioner, the CPU stands by 30 degrees, the fan rotates at 1700, and the current sound appears. But when the BIOS turns off the intelligent temperature control, the current sound disappears when the fan runs at full speed. A friend said that there was no current sound when plugged into the 3PIN interface, because 3PIN does not support intelligent temperature control, and the fan will automatically run at full speed. It doesn't matter. If you have the same problem, remember to take regular care of the fan.

The summary is good. Although there are flaws, it is still acceptable.

Strong heat dissipation performance, suitable for high heat CPU. The Cool Pioneer used in my chassis has a standby of 25 degrees in a 20 degree environment. It uses the i7 2600 default 3.4G frequency to fully load the CPU, and only 35 degrees after 15 minutes. Very good noise control. It can also achieve a certain mute effect when the fan is running at full speed

The installation process on the installation manual is all illustrated without text description, so it is difficult to understand what it means. It was successfully installed after carefully reading the manual for more than half an hour. The weight of small radiators is a little larger than that of ordinary ones (of course, compared with those of heavyweight radiators, the weight is a piece of cake)

On the whole, if you can fully understand the illustrations in the instructions and successfully install them (the instructions are difficult to understand), the cost performance of this radiator is quite high, and it is suitable for people with strong hands-on skills to purchase

My i5 760 starts at 21 degrees, standby at 23~24 degrees, and plays at 45 degrees for a large single machine. I have tested it, and it drops back to 23 degrees within 10 minutes (the room temperature is 10 degrees). It starts at 160 degrees in mid January. I wonder how the heat dissipation capacity is in summer? I thought that the side panel of the chassis might not be covered. After installation, I found that there was still a small space (my chassis is an ordinary Jinheda 8205B). The pure copper heat sink, which is connected to the CPU, is a bit fake. It should be aluminum (laymen don't understand why that small piece should be made of aluminum. Aluminum has a large specific heat capacity?)

It's a bit heavy. After installation, it is recommended to lay the chassis flat. The price is a little high. The original is not a double fan (this seems not a disadvantage)

A good radiator, a good choice for middle end players

My I3-530 original fan, 1200-1500 rpm (room temperature 10-20 ℃), the temperature is about 20 ℃, and in winter it is 10-20 ℃. Just started this fan, CPU fan 10-12 degrees, very powerful (room temperature 10-20 degrees)

I don't know how to adjust the speed. It's troublesome. It's 2000 rpm, and the sound is not muted. The original fan is not muted yet. I don't know how to do it

Fairly good, heat dissipation, I don't know how to set the speed. I hope the master can send a detailed method of speed setting.

Good heat dissipation, quite quiet. My Yilong 2 Quad Core 955 is 43 degrees when it is in standby, less than 55 degrees when it plays games, and the revolution control is also good, about 1300 revolutions when it is about 50 degrees.

The installation is troublesome, and the player needs some hands-on ability. It would be better if the backplane could increase the contact area with the motherboard.

It is suitable for middle and high-end players to choose and buy. Now you can get it online for 150 yuan, and the cost performance is obvious.

1. Four rubber brackets are used between the fan and radiator to effectively reduce fan noise.
2. The heat pipe has a good heat dissipation capacity. With the original Intel PE5200 fan, the CPU temperature has been around 60 degrees. Today, the Red Sea mini version is used, and it has dropped to 37 degrees!
3. The overall workmanship was very good.
4. Cheap price

1. The connection process between the base and the mainboard is hard, which will cause damage to the snap of the base
2. The connection between the heat sink and the base is weak and needs to be strengthened.
3. The fan is smaller than the standard version, and the workmanship is also poor.

For the heat pipe radiator with only 65 yuan, the Red Sea mini version is definitely the first choice for beginners!