At the beginning, I heard that x3d heat accumulation was a bit serious, so I chose this fan with 6 heat pipes and 12 cm for heat dissipation. In fact, when I was on the computer, I found that the design to avoid memory was lonely. When I was coming to install the light bar, I could only plug it into slots 3 and 4. At least it could form a dual channel. On the contrary, when I installed the CPU, the temperature could not be changed. The fan could take off directly at 70 degrees,The am4 motherboard can not be installed horizontally. Every time I remove the heat sink, I uproot it. My whole life is contributed by this game.The product and quality itself are good, which means that the design is slightly poor.
The surface is sprayed with ceramic antioxidant, which is a downforce scheme. The base and fins are designed as a whole. The heat pipe and the base are not non direct contact. The combined thickened fins of 6 heat pipes are suitable for steel gun platforms with limited vertical space, but want powerful heat dissipation.
????Finally, I started to deal with it. Is it true that the face value has no words?,The material is very good and the price is cheap. We should stock it up while the event is going on
It's impossible to hold down at all. The main board is seriously hot, and the roast chicken is 100 degrees.The fan is a little better on the contrary, but the standby temperature is lower than that of ordinary use, and the temperature of roast chicken is 100 degrees.The inextricable radiator can only lock 65 watts of power. It's useless!You can't return the goods after using it. The quotation only supports 7 days, and the price will be reduced by 40% in more than a week
The appearance is online and the height is appropriate.It does not affect the heat dissipation armor of the small motherboard.The fan is still a little loud.
Very good. It can provide sufficient heat removal capability in the ITX chassis, but it seems to interfere with the Gigabyte b760i d4. You need to remove the m2 heat dissipation armor under the motherboard to install the heat sink.
The flash scale S400 V2 is used. The processor fan of this chassis is limited to 67mm in height, and the motherboard is usually a quadrangle design, but this fan can be inserted perfectly!!!The mysterious power of the six heat pipes drives the i5 12600K heat treatment, which is completely no problem. Playing the game is completely manageable, but only one thing needs to be noted. This radiator has a limit on the memory height, and can only use DDR5 memory of standard height. The vest can not exceed the height of the memory module, otherwise it will not be installed. It is successfully installed into the ITX chassis, and the RGB light pollution will be lit at a time,It's cool to support Shenguang synchronization
The heat dissipation effect is moderate. The fan has a large air volume, but the fan noise is too loud. 1500 rpm is just like taking off.I plan to buy a cat fan to replace it.Conclusion: Regret.
I searched the website myself. It seems that only this radiator can meet the downforce of 12cm fan and the height of 63cm at the same time. The overall workmanship is also good. The white model also has rgb
Very easy to use!And the heat dissipation capacity is very strong!The only problem is the iron sheet backplane on the back, which is too big. It is a bit top to the electronic components on the back of the motherboard, but I used insulated plastic sheets to separate them!Perfect!Although the height of the hummingbird case is limited to 60mm, the actual measurement shows that this 63mm high radiator can be completely installed!Give everyone a reference!
Very unfriendly to the old models. The lights need to be purchased separately. For the fans that cost one or two hundred yuan, the lights need to be purchased separately
For the new platform, the original motherboard heat sink from a to i is just matched with the x67. The new rog board heat sink is a little high, so I can only replace it with a new heat sink. After a trial, the effect is not much different from that of the x67. I can say 124 has no pressure!!
The radiator of the overclocking three hummingbird 1 I100 PRO chassis is recommended. The chassis is limited to 60mm in height. The HX6200D radiator can be installed in the physical test, without affecting the upper side panel of the chassis
It's a very good downforce cooling fan, but it's a pity that the Beggars' version motherboard I bought doesn't support the colorful light effect of the fan.The installation process is very simple. Even Xiaobai, who installed the machine for the first time, can easily get started. The customer is also very patient in answering questions.
I bought a mechanical master's e24 and the height is limited to 65. It must be that I can only use this radiator card to easily press a 13490. It's still OK and very beautiful
The effect is not bad. It's not bad. The main reason is to look good. It's enough to be handsome. I originally prepared the ITX chassis, but I changed the scheme temporarily. Use it first, and then change it slowly. It's enough anyway hahaha