Handsome, I installed a c12b in the back, and the 11700k silent frequency has dropped from 90 ° to about 75 °, which is still OK!The chassis fan has also been replaced with six rog fans, which has led to the temperature down and the noise coming up. Now the chassis has to be replaced for the 11700k. It's a pit. It's no different from the 10400f frame number. It's vomited...
Like the TA120EX, reflow soldering, Jun hot plate base, full nickel plating, high-performance 14cm fan, and the price is also dozens higher than the TA120. However, from the last two comparison pictures of 140ex and 120ex base heat pipe welding, 140ex is not fully welded, and there are many obvious gaps. 120ex is fully welded, and there is obvious traces of cleaning excess solder. From this point of view,The 140ex is a bit jerry built, and I don't know whether it is an individual case, but how many hidden dangers to the heat transfer efficiency depend on the actual effect of the machine.
It's a good thing. The TS140P was not treasured before. It was second-hand. Later, I regretted that I wanted to get it back, but it basically didn't sell.There are 14 new models, and we hope to have a TA140EX power later.
This thing has been tried on the computer. The silicone grease of mocooling x, with room temperature of 26 and pressure of 5900X and 10900K, is in good condition. It can play with the earlier version of fs140 and the ordinary pa120, and the lag is no more than 2 ℃. It's a surprise for a single tower. The temperature difference on IU will be more intuitive.But I still can't fight FC140. Anyway, I'm too greedy.
There are only 5 heat pipes in total, but there is a clear gap between the main heat pipe in the middle and the copper base. Is this the quality of Limin's products?Do I buy this radiator for more than 200 yuan?
The fan is very large, the heat dissipation effect is good, but the volume is too large to install the graphics card. It is recommended to buy a MATX motherboard to calculate the length
The price is not cheap, but the workmanship is poor. There is a gap between the base and the heat pipe, which will certainly affect the heat conduction efficiency, disappointing!
This fan is really good. The key is that it is small in horizontal volume. I use the ATX standard board. I feel that the use of matx is more coordinated, the air volume is large, and the reflow process is perfect. There is no problem with the i7 11700 that presses me, and the installation is much better than those of the * * sub fans, so there is no danger of bending the pins of the main board.
Good workmanship and texture.The 58X U is too hot. The room temperature is 30 degrees and the game U is 60 or 70 degrees.The 240 water is replaced, and the single tower is convenient for plugging and unplugging the memory, but it also needs certain efficiency. This single tower is a good option
It is good for the people because of its high quality and low price, but can this manual be simpler? Somehow, it's positive and negative... It's really quiet after installation, and the effect is excellent
Say the important thing three times, pay attention to the height of the fan... pay attention to the height of the fan. Because I bought this, I changed the chassis. You know, the height of 156 is really high.
It should be the second time to buy Limin's CPU radiator, which is the 14 # fan model. This model has a small defect. The heat pipe on the base is a little green, commonly known as oxidized!The introduction of the non blocking graphics card still depends on the motherboard. Generally, it will block, but the fixed steel wire of the fan will protrude and just interfere with the graphics card.
The package is complete, and the installation is convenient. The installation plug-in of different platforms is equipped. There is no problem in the installation, and the memory module will not be covered. For the M-ATX motherboard, the solid state disk at the M.2 interface may be slightly covered
