Interior space: As a designer of sheet metal chassis and a person who has always used Patriot chassis, this time I said that there are basically some problems in the chassis I have used. The design is not reasonable, but the innovation is good... It is recommended to add a partition at the place where the power supply is placed, not to cover it completely, but it is recommended to use a flat roof to put it aside, mainly to isolate the power supply,Increasing the fixation of the power supply can also increase the aesthetics Appearance: The appearance is very beautiful. I also like the white color, but some details are not good. For example, when the chassis fan turns up, the side transparent plate shakes, even when it is tightened, and the switch is also very loose, which makes noise. It is recommended to add damping stickers to prevent vibration, Heat dissipation effect: the chassis should consider more water cooling, and be in good order Workmanship quality: this is not bad, very hard core Product packaging: The accessory box is placed in the mechanical hard disk partition at the bottom, and it is really slow to take out. I took out the box directly after disassembling the box. Although it can be taken out by removing the hard disk partition, it will be somewhat troublesome. No one dares to remove the hard disk cover when inspecting the accessories for the first time On the whole, except for some details, others are really good. If you add damping stickers to accessories, it will be a killer. Unfortunately, there is no chassis, it is still a really fragrant warning. But I think I wrote so much, and no one seems to read it. Feel free, and it's good to be noticed
This case designer is so poor. I didn't expect to buy such anti human products in 2021! 1. The fan position above the processor does not have a fixed position for the fan. It is clear that a 12cm fan can be plugged in. Just punch a hole.(This is absolutely unbearable! As long as you install a computer, you will definitely use this fan bit!) 2. Why does the front fan position bend outward and thicken? The 12cm fan obviously has enough space to be installed on the outside. I installed the fan on the outside and the front cover plate could be covered, but your front cover plate is also air inlet on both sides, and the air inlet of the fan is blocked by the iron plate of the cover plate after being covered.So I bought three thin fans.(When the fan is installed outside, the third long pcie can be used to install the 40g network card) The case of 3.269 is not cheap. Why is the thickness of the plate about the same as that of the 100 yuan class!And even if the side glass is small and ugly, there is no way to open the door!Those who care about these can buy more than a few dozen game pills with high quality. In addition to the advantages of small size and price, the overall evaluation is completely inferior to the next Kai Yuan t1.In particular, I suggest you fire the designer. I bought three more Kai Yuan t1
Internal space: Internal space: The space is OK Workmanship quality: excellent workmanship Heat dissipation effect: heat dissipation generally, especially after 240 water cooling is installed, there is wind resistance in the cold exhaust of the air outlet, high heat, and the heat of the graphics card cannot be discharged Appearance: excellent appearance
Workmanship quality: the thickness of the plate is OK, and the price is affordable! Product packaging: the packaging is also in place, without damage! Support video card hoisting, very good!
Disdain it. The case is made of iron. Look at the thickness of the old case at home and then look at this. It's light in the hand. I think the water pump will be withdrawn if it is not suitable on the road.The highlight of this case is the vertical layout, which can save a lot of space. The front panel can place a cold exhaust of about 360, and the rear can also be 360 after visual inspection. Because the graphics card is placed vertically, the water pump and water tank can be placed. The height of the case is close to 450, and it is just good to put it in the cabinet. Let's have a look at the photos after installation
Very good. The original chassis is a little noisy.The new one is much quieter.Wait for Series 40.Install the graphics card vertically, without damaging the card, and the air duct can be connected back and forth.The price is also cheap, the workmanship is very good, very heavy.
The chassis is pretty good. The overall effect is very good after pasting the sticker. Just a reminder, if the video card is over 32cm.The following mechanical hard disk bit must be removed
The only thing I'm not satisfied with is that there is no front USB – c Everything else is OK At first, I was worried that two 3060 Raptors could not be put in. I thought there were two more 3-slot cards. They were all OK. At the bottom, it was still possible to install a piece of machinery through visual inspection The space is enough
Internal space: not big or small Workmanship quality: the workmanship is not bad, the quality is not bad Heat dissipation effect: the chassis has good heat dissipation, and this air duct is amazing Appearance: the appearance is really beautiful The mechanical hard disk of this case is too high. It's a bit troublesome to put it on the bottom after removing it. There is no screw position
Workmanship quality: Workmanship is worth the price. The bottom of the switch is too narrow. If you can install a fan, you can't add a cold exhaust, Internal space: the lower part of the switch is too narrow. It can be installed with a fan, but not with a cold exhaust, Appearance: It would be better if there was a power cover plate with another hole. The power supply line of the motherboard cannot be handled.
Figure 1: Compared with the Patriot Aurora E20, the height is about the same, the thickness is about 1cm more, and the depth is about 3Cm more.Figure 2: This bar shaped hole is changed into a wavy one.Figure 3 Figure 4: What are these two holes for? Your hands can go in
Internal space: very large, no problem installing the motherboard. Workmanship quality: the quality is unknown, and it is very heavy to lift. Appearance: Very good appearance, but there are too few colors.
Internal space: It's a bit exaggerated to see others say that the back line is "rich and redundant". It's just enough for the normal installation of independent single graphics cards, but it's hard to do so.Later, it should be noted that SATA data cables cannot be bent, and straight data cables should be prepared in advance. Workmanship quality: I think it is acceptable and cost-effective.
Internal space Workmanship quality: good workmanship and strong steel.Both USB interfaces on the front panel are USB 3.0, which is quite unexpected Heat dissipation effect: OK, the side glass is a little hot when playing large games, and it will be evaluated after a period of time Appearance: simple and elegant Product packaging: foam and plastic bag inside for protection
Internal space: excellent Workmanship quality: 8 points Appearance: excellent Heat dissipation effect: excellent Product packaging: excellent Although the video card is upright, it will not bend the video card, but it will affect the appearance and the chassis duct
Internal space: large, but module power supply is also required Workmanship quality: I feel very good Heat dissipation effect: five 1800 rpm fans, the power supply fans also face inward, max! Appearance: Not bad, simple black and white, and a router on it is enough for heat dissipation
It's really a beautiful case, but the redundant power cords are stacked together. It looks really messy at a certain angle Internal space: large space, high utilization rate Workmanship quality: how does the plate feel Heat dissipation effect: I added 5 fans, which may be the RX590 graphics card. The temperature of other hardware is too high, but it is much better than the previous chassis
