The power failure of Little Swan washing machine may be caused by the following reasons:
1. Power failure: first, check whether the socket of the washing machine works normally. You can try to plug other appliances into the same socket to see whether they can be used normally.If other appliances cannot be powered on, the problem may be the socket or power supply line.
2. Fuse disconnection: Each washing machine is equipped with a fuse to protect its internal components.If the washing machine suddenly turns off, the fuse may be disconnected.You can open the panel of the washing machine, find it next to the control board and check whether the fuse is in good condition.
3. Switch fault: If the above two points are all correct, the switch of the washing machine may be faulty.At this time, it is necessary to remove the panel and carefully check and test whether each switch assembly works normally.
4. Supplier quality problems: although rare, sometimes new products have quality problems.If you are sure that all the above steps are correct and no part is damaged during the replacement process, please contact the Cygnet after-sales service center for consultation and repair.
In short, when the Little Swan washing machine is not powered on, you can first check whether the socket and fuse work normally, and then check whether the switch assembly is faulty.If there are no problems above, it is recommended to contact professional maintenance personnel for further diagnosis and repair.
Reasons for the power failure of the automatic washing machine: the washing machine is powered off due to the power failure of the external plug or damage;The power line of the washing machine is disconnected, causing the whole machine not to be powered on;The fuse of the washing machine is blown, so that the washing machine is not powered;The power circuit of the computer board is damaged, resulting in no power operation;The washing machine circuit connection line has an open circuit fault;Solutions for the above fault conditions: carefully check whether the external drain plug is normal and whether there is any damage to the power supply;Check the break point of the washing machine power line, reconnect or replace the new power line;Replace the safety pipe of the washing machine;Replace the computer program control board according to the original model to ensure its normal operation;Check the internal connection wire of the washing machine, connect it in time if there is a break, and conduct insulation treatment.
Dear friends, you can call the after-sales customer service number of Little Swan or provide the WeChat service number of Little Swan to make an appointment with them, so that the after-sales service can conduct on-site confirmation, analysis and maintenance, which is very convenient.
1. The first reason is to check whether the socket has power. After the washing machine is plugged into the power socket, press the power switch, and the operating panel of the washing machine should be on.If it doesn't light up, the circuit or fuse is burned out.
2. The second reason is that the leakage protection is activated due to water leakage on the circuit or other reasons, resulting in no power supply to the washing machine. It is recommended to unplug the power supply and take it to the after-sales or electrical maintenance station to check the problem.
3. The third reason is that the power cannot be connected.Cause and how to do: Automatic power-off function. If the power switch is pressed, the power switch will jump up and reset immediately. The power switch may be damaged, so the power switch should be replaced;The power supply is directly controlled by the computer board. If the power supply cannot be connected, the keys may be stuck or the computer board may be damaged;The computer board may be affected by water or moisture due to improper use by the user, which may cause the computer board to malfunction due to short circuit. Once the power is turned on, the reset coil of the power switch will be instructed to cut off the power. At this time, the computer board should be replaced.
4. The fourth reason is to first check whether the power supply is normal, which is an external fault.If the computer board is normally protected by water ingress or moisture, the internal of the computer board is short circuited. Remove the board to see where there is a burned part in the power supply. If it is badly burned, replace the board.
5. The fifth reason is whether the tap is open.
6. The sixth reason is that the motor plug-in wire is in poor contact or the motor is damaged.
1. The first reason is to check whether the socket has power. After the washing machine is plugged into the power socket, press the power switch, and the operating panel of the washing machine should be on.If it doesn't light up, the circuit or fuse is burned out.
2. The second reason is that the leakage protection is activated due to water leakage on the circuit or other reasons, resulting in no power supply to the washing machine. It is recommended to unplug the power supply and take it to the after-sales or electrical maintenance station to check the problem.
3. The third reason is that the power cannot be connected.Cause and how to do: Automatic power-off function. If the power switch is pressed, the power switch will jump up and reset immediately. The power switch may be damaged, so the power switch should be replaced;The power supply is directly controlled by the computer board. If the power supply cannot be connected, the keys may be stuck or the computer board may be damaged;The computer board may be affected by water or moisture due to improper use by the user, which may cause the computer board to malfunction due to short circuit. Once the power is turned on, the reset coil of the power switch will be instructed to cut off the power. At this time, the computer board should be replaced.
4. The fourth reason is to first check whether the power supply is normal, which is an external fault.If the computer board is normally protected by water ingress or moisture, the internal of the computer board is short circuited. Remove the board to see where there is a burned part in the power supply. If it is badly burned, replace the board.
5. The fifth reason is whether the tap is open.
6. The sixth reason is that the motor plug-in wire is in poor contact or the motor is damaged.
Reasons for power failure of automatic washing machine: one The washing machine is not powered because the external plug is not powered or damaged; two The power line of the washing machine is disconnected, causing the whole machine not to be powered on; three The fuse of the washing machine is blown, so that the washing machine is not powered; four The power circuit of the computer board is damaged, resulting in no power operation; five The washing machine circuit connection line has an open circuit fault; Solutions for the above faults: one Carefully check whether the external plug is normal for power supply and whether there is any damage. Power on or replace it in time; two Check the break point of the washing machine power line, reconnect or replace the new power line; three Replace the safety pipe of the washing machine; four Replace the computer program control board according to the original model to ensure its normal operation; five Check the internal connection wire of the washing machine, connect it in time if there is a break, and conduct insulation treatment.
